PassionFord - Ford Focus, Escort & RS Forum Discussion
Adapter on top of coleys
Adapter on top of coleys
0 2015/08/06 10:51:21
Mondeo adapter (to try) and tilton that arrived today from competition supplies
Mondeo adapter (to try) and tilton that arrived today from competition supplies
0 2015/08/05 08:03:47
Tilton with Mondeo adapter plate
Tilton with Mondeo adapter plate
0 2015/08/05 08:01:53
0 2015/08/03 12:33:00
0 2015/07/19 08:46:29
0 2015/07/19 08:46:18
0 2015/07/19 08:46:10
0 2015/07/12 11:38:27
A pic to show my hero sideways style
A pic to show my hero sideways style
0 2015/07/10 04:38:43
0 2015/06/22 12:27:16
Just took this from the 3ft front to back side of the tank, it gives you some idea of their size
Just took this from the 3ft front to back side of the tank, it gives you some idea of their size
0 2015/05/29 09:57:33
Rubbish iPad pic
Rubbish iPad pic
0 2015/05/29 09:55:53
I think this should go here too
I think this should go here too
0 2015/05/14 10:54:10
Here you can see the cleaned strut tops
Here you can see the cleaned strut tops
0 2015/05/11 07:25:37
Polished strut brace now clears all of the engine
Polished strut brace now clears all of the engine
0 2015/05/11 07:24:38
old vs new (std 4x4 cossie)
old vs new (std 4x4 cossie)
0 2015/05/05 04:54:58
Adam, these are MT motorsport 300mm rears using saph 4x4 std calipers (rebuilt)
Adam, these are MT motorsport 300mm rears using saph 4x4 std calipers (rebuilt)
0 2015/05/05 04:53:11
Rear box made as a replica of the original T16, it is upside down in the pic so the exit is actually on the passenger side of the car.
Rear box made as a replica of the original T16, it is upside down in the pic so the exit is actually on the passenger side of the car.
0 2015/05/05 03:31:46
0 2015/04/28 03:38:59
0 2015/04/26 05:00:55
I did a vry quick primer and repaint on the bay as was keen to get the engine back in, it can go to a body shop when the engine is rebuilt
I did a vry quick primer and repaint on the bay as was keen to get the engine back in, it can go to a body shop when the engine is rebuilt
0 2015/04/26 04:59:42
Atleast the diff cover looks good and should not break!
Atleast the diff cover looks good and should not break!
0 2015/04/26 04:58:51
Here you can see the crack under the bolt at the top of the bell housing....thoughts? I want to run the car to make sure everything else works but how long would this hold even with gentle use? 500ftlb is a lot of twist!
Here you can see the crack under the bolt at the top of the bell housing....thoughts? I want to run the car to make sure everything else works but how long would this hold even with gentle use? 500ftlb is a lot of twist!
0 2015/04/26 04:57:12
pipework to feed the pump under the car
pipework to feed the pump under the car
0 2015/04/08 05:38:53
pump under the car on anti vibration mounts
pump under the car on anti vibration mounts
0 2015/04/08 05:37:59
reservoir in boot, this will be trimmed professionally
reservoir in boot, this will be trimmed professionally
0 2015/04/08 05:36:57
Here it is zoomed in on Turbo boost instead of revs...the image on the camera is not sharp but in real life it is a crisp tft touch screen
Here it is zoomed in on Turbo boost instead of revs...the image on the camera is not sharp but in real life it is a crisp tft touch screen
0 2015/04/03 07:46:13
0 2015/04/03 07:42:36
Here you can see it against the rest of the dash flocked in red
Here you can see it against the rest of the dash flocked in red
0 2015/04/03 07:41:26
0 2015/04/03 07:40:40
0 2015/04/03 07:39:48
Here is the front prop from skyline matched to the cossie front prop for mock up purposes, I dropped it off with Propshaft services in Feltham....proper old skool workshop, they think both props will be ready by the end of this week.
Here is the front prop from skyline matched to the cossie front prop for mock up purposes, I dropped it off with Propshaft services in Feltham....proper old skool workshop, they think both props will be ready by the end of this week.
0 2015/03/30 07:18:01
Quick coat of paint before dyna mat (fatmat)
Quick coat of paint before dyna mat (fatmat)
0 2015/03/30 07:16:56
Tunnel welded in, seam sealed and ready for paint.
Tunnel welded in, seam sealed and ready for paint.
0 2015/03/30 07:15:41
Tunnel is in and painted, I am using rubber to seal the gear stick hole over the shifter. I will then dynamat (fat mat) and then cover the whole floor in a rubber "decoupler" to stop any vibrations.
Tunnel is in and painted, I am using rubber to seal the gear stick hole over the shifter. I will then dynamat (fat mat) and then cover the whole floor in a rubber "decoupler" to stop any vibrations.
0 2015/03/30 07:12:37
Caddy 20v Turbo with Electric opening cover, lowered on coilovers and axle flip with big disc conversion all round and full respray.
Caddy 20v Turbo with Electric opening cover, lowered on coilovers and axle flip with big disc conversion all round and full respray.
0 2015/03/19 05:32:11
30mm dia for centre push
30mm dia for centre push
0 2015/03/17 10:01:40
centre push 28.5 ish diameter internal
centre push 28.5 ish diameter internal
0 2015/03/17 10:00:27
I had to take the seats out to do the cutting and welding so I thought I would stick a pic up. These are retrimmed RS Turbos, they have heated seat backs and bases. The Door Trims are done the same but with red carpet at the bottoms to mimic the T16 door cards from the 205.
I had to take the seats out to do the cutting and welding so I thought I would stick a pic up. These are retrimmed RS Turbos, they have heated seat backs and bases. The Door Trims are done the same but with red carpet at the bottoms to mimic the T16 door cards from the 205.
0 2015/03/02 03:59:33
another angle, you can see the big brakes in this pic too.
another angle, you can see the big brakes in this pic too.
0 2015/02/02 02:26:17