Tim Garringtons WRC V8, Engines back in and bulk heads nearly completed! 03/05/11
#202
Part of the Furniture
![Default](https://passionford.com/forum/images/icons/icon1.gif)
will be using rose joint for lower mount and remake top mount to take original
column fixing
#203
Lucifer II - 666
Thread Starter
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Looking amazing Tim! I'll pop over later in the week mate
![](https://passionford.com/forum/images/smilies/roi.gif)
#204
How much! I`ll have it!
Join Date: Nov 2007
Location: Cumbria
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Wink Wink! Nice choice of engine there chap ![](http://i768.photobucket.com/albums/xx323/v8ndy/24102009142.jpg)
Great looking project, I did try it for size in the 206`s engine bay and thought this could fit! But it was already destined for the TVR
![](http://i768.photobucket.com/albums/xx323/v8ndy/24102009142.jpg)
Great looking project, I did try it for size in the 206`s engine bay and thought this could fit! But it was already destined for the TVR
Last edited by v8ndy; 07-05-2011 at 09:35 PM.
#205
PassionFord Post Whore!!
iTrader: (2)
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Slowed down a bit a s ive been helping m8's out with there project's
![Big Grin](https://passionford.com/forum/images/smilies/icon_biggrin.gif)
But ive started to mod my loom's at the mo and im gonna have to finish them off before i can prep it for paint , Guess ill have to pull my finger out
![Wink](https://passionford.com/forum/images/smilies/icon_wink.gif)
Enjoying back working on it with no stress to finish it
![Big Grin](https://passionford.com/forum/images/smilies/icon_mrgreen.gif)
Would love a V8 monster in the front of it real envious of you and your build
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
#206
Part of the Furniture
![Default](https://passionford.com/forum/images/icons/icon1.gif)
nice set up you have ,what size is the kenne bell s/c? and what transmision you going to run
#207
Advanced PassionFord User
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Just read this thread from start to finish. Amazing! this is you when you have had a disk removed, What were you capable of when fully fit. Stunning work Tim.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
Last edited by jonfoc; 08-05-2011 at 09:56 AM.
#208
How much! I`ll have it!
Join Date: Nov 2007
Location: Cumbria
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
![](http://i768.photobucket.com/albums/xx323/v8ndy/Tvr/20100531_001.jpg)
Last edited by v8ndy; 08-05-2011 at 06:57 PM.
#209
Part of the Furniture
![Default](https://passionford.com/forum/images/icons/icon1.gif)
small update
pedal box in place
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar002.jpg)
with dash for test fit
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar003.jpg)
need to make lower column extension so got 2 rack pinions from my local rack re conditioners and some bar
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar005.jpg)
ground of teeth to end up with shaft to insert into bar
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar008.jpg)
drilled into end of bar and drilled through sides for welding
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar006.jpg)
pressed ends in both ends ready for welding
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar007.jpg)
shaft with new uj's had top joint made with STD upper part with lower to fit splines
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar013.jpg)
more updates end of week
i'm trying to get car somewhere near so can take to ford fair but we will have to see how things go?
pedal box in place
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar002.jpg)
with dash for test fit
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar003.jpg)
need to make lower column extension so got 2 rack pinions from my local rack re conditioners and some bar
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar005.jpg)
ground of teeth to end up with shaft to insert into bar
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar008.jpg)
drilled into end of bar and drilled through sides for welding
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar006.jpg)
pressed ends in both ends ready for welding
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar007.jpg)
shaft with new uj's had top joint made with STD upper part with lower to fit splines
![](http://i1002.photobucket.com/albums/af148/timbhp/16maycar013.jpg)
more updates end of week
i'm trying to get car somewhere near so can take to ford fair but we will have to see how things go?
Last edited by timbhp; 16-05-2011 at 08:23 PM.
#211
PassionFord Post Whore!!
iTrader: (2)
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Nice work ![Big Grin](https://passionford.com/forum/images/smilies/icon_biggrin.gif)
Are you extending the colum back to make up for moving the seat back?
Gonna be a nice tight fit down the side of the clutch pedal with that beefy gearbox there ay?
![Big Grin](https://passionford.com/forum/images/smilies/icon_biggrin.gif)
Are you extending the colum back to make up for moving the seat back?
Gonna be a nice tight fit down the side of the clutch pedal with that beefy gearbox there ay?
#213
Part of the Furniture
![Default](https://passionford.com/forum/images/icons/icon1.gif)
yes have repositioned column but still have adjustable column so got a bit more adjustment if reqd
and moved pedal box back,
the pedals are not that cramped with work boots on still loads of room so all should be good
#215
Part of the Furniture
![Default](https://passionford.com/forum/images/icons/icon1.gif)
small update
pedal box mounted but tunnel was wrong shape and made foot position uncomfortable so reshaped
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate007.jpg)
column in place so can make up mounts
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate013.jpg)
i will use rose joint for lower steering column mount so need to make mounting point so cut and folded sections ready for welding
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate009.jpg)
clamped together
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate010.jpg)
getting a few bits together
1300 bhp + fuel pump and filter
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate020.jpg)
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate019.jpg)
escort mirror image expansion tank made for me by pro alloy they are also making me another tank for other side for charge cooling system so will have one each side
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate025.jpg)
tilton 3 in 1 unit to feed master cylinders
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate022.jpg)
just a few of the hose ends needed for all fluids
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate023.jpg)
a few stainless exhaust components so i can finish exhaust system
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate018.jpg)
offered pro alloy fuel tank tray in position so can work out mounting for it
pedal box mounted but tunnel was wrong shape and made foot position uncomfortable so reshaped
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate007.jpg)
column in place so can make up mounts
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate013.jpg)
i will use rose joint for lower steering column mount so need to make mounting point so cut and folded sections ready for welding
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate009.jpg)
clamped together
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate010.jpg)
getting a few bits together
1300 bhp + fuel pump and filter
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate020.jpg)
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate019.jpg)
escort mirror image expansion tank made for me by pro alloy they are also making me another tank for other side for charge cooling system so will have one each side
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate025.jpg)
tilton 3 in 1 unit to feed master cylinders
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate022.jpg)
just a few of the hose ends needed for all fluids
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate023.jpg)
a few stainless exhaust components so i can finish exhaust system
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate018.jpg)
offered pro alloy fuel tank tray in position so can work out mounting for it
![](http://i1142.photobucket.com/albums/n609/timsescortv81/24mayupdate014.jpg)
#217
Lucifer II - 666
Thread Starter
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Thread / built ended. Due to ill health.
If you would like to purchase the car or any substantial parts from it please PM Tim, he is a gold member and will have for sale adverts up soon.
Thanks for viewing, thread now closed.
If you would like to purchase the car or any substantial parts from it please PM Tim, he is a gold member and will have for sale adverts up soon.
Thanks for viewing, thread now closed.
Thread
Thread Starter
Forum
Replies
Last Post
ekjim
General Car Related Discussion.
6
17-08-2015 08:57 PM
Gadget
Ford Escort RS Cosworth
1
14-08-2015 07:19 AM
Gadget
Ford Sierra/Sapphire/RS500 Cosworth
0
13-08-2015 08:19 PM
CabrioTurbo
General Car Related Discussion.
1
01-08-2015 11:04 AM