Reyland Focos. Shes got her new clothes on!!04/07/09
08-06-2008, 07:25 PM
#401
Andy and the lads have done a stunning job on this, the paints not quite there yet, still a few finishing touches to be added...............................
I'll let the pics do the talking
Bonnet and side reps on
Shiney new Pro Alloy fuel cell and enough 'quip to settle the national debt
Got the flocked dash in too(Cheers Doug
aka Garage19) and trial fitted one of the seats we may be using
started to route the fire extinguisher system too
I'm tackling the loom on Wednesday, cause I've been sunning myself in Blackpool all weekend and avoiding any hard graft
so I'll put some more pics up then
Enjoy 
I'll let the pics do the talking
Bonnet and side reps on
Shiney new Pro Alloy fuel cell and enough 'quip to settle the national debt
Got the flocked dash in too(Cheers Doug
aka Garage19) and trial fitted one of the seats we may be usingstarted to route the fire extinguisher system too
I'm tackling the loom on Wednesday, cause I've been sunning myself in Blackpool all weekend and avoiding any hard graft
so I'll put some more pics up then
Enjoy
08-06-2008, 11:18 PM
#410
Thats where the filler cap was, welded it up but lost the line a bit when it was painted, so its being re-done
Twins There's most likely gonna be a set of better seats in there before it hits a track, just using these to see a more complete car, makes you think you've got less work to do when there's more bits bolted in!!
Coley cheers mate
Twins There's most likely gonna be a set of better seats in there before it hits a track, just using these to see a more complete car, makes you think you've got less work to do when there's more bits bolted in!!
Coley cheers mate
10-06-2008, 08:56 AM
#416
Virgin
Join Date: Jun 2008
Location: Eindhoven, The Netherlands
Posts: 12
Received 0 Likes
on
0 Posts
My my, what a project that has been! I'm new here, but am amazed at the projects people take on. What I have done and will be doing is peanuts compared!
Great project!
Great project!
14-06-2008, 12:42 AM
#423
Too many posts.. I need a life!!
iTrader: (3)
Join Date: Sep 2007
Location: wirral / nottingham
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
think its going to be this week paul the engine all goin well will be in place next saturday nite so if the car is painted an engine in we will put up the pics next weekend
Last edited by f6cus; 14-06-2008 at 07:36 AM.
14-06-2008, 04:20 PM
#426
Too many posts.. I need a life!!
iTrader: (3)
Join Date: Sep 2007
Location: wirral / nottingham
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
yer its nearly done mate got the reyland hydraulic clutch cylinder fitted today and few other parts done engine in next saturday afternoon got to go to reyland saturday mornin to pick me brakes and new gearbox up plus loads of other things
28-06-2008, 06:14 PM
#433
Too many posts.. I need a life!!
iTrader: (3)
Join Date: Sep 2007
Location: wirral / nottingham
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
engine and box are in its back on wheels and the front end built up pics will be up in abit didnt take many its been one of them days had a twat of a time getting the old spigot bearing out an it went down hill from there 
28-06-2008, 08:22 PM
#435
Update time!.........................
Spanky new Tremec TKO600 gearbox from Martoon With a fancy new centre push hydraulic clutch fitted, forgot to take any pics of it though
So Martoon could you stick a pic up please?
Bolted to the engine ready for fitting, after swearing at the spigot bearing for 3 hours
And the YB has a new home
Slight mod to the floor to let the gear stick through (done with a hacksaw for now Pics when its tidied and done properly
Should have some more piccies and progress tomorrow, the diffs fitted in the beam, just got to modify the diff hanger to get it to fit
Get the prop in, mod the gearbox mount to finalise that, wire it all up, fit the brakes and its done!
nearly
Spanky new Tremec TKO600 gearbox from Martoon
With a fancy new centre push hydraulic clutch fitted, forgot to take any pics of it thoughSo Martoon could you stick a pic up please?
Bolted to the engine ready for fitting, after swearing at the spigot bearing for 3 hours
And the YB has a new home
Slight mod to the floor to let the gear stick through (done with a hacksaw for now
Pics when its tidied and done properlyShould have some more piccies and progress tomorrow, the diffs fitted in the beam, just got to modify the diff hanger to get it to fit
Get the prop in, mod the gearbox mount to finalise that, wire it all up, fit the brakes and its done!
nearly
