Highest torque figure from a Zetec turbo?
25-04-2012, 10:37 AM
#1
Highest torque figure from a Zetec turbo?
Lee at Devil Developments has just mapped Alex ST's car after the head lifted at Central Day. You may have seen the car at the show:
Well Lee has just mapped it to 2 BAR on the GTX30 turbo, using M12 head studs and it's made 488 lbft of torque along with 542 bhp!
Is this the highest torque figure for a Zetec now? I know Paul Johnson had more power but can't recall his torque figure?
Mental car anyway, can't wait to see it perfrom.
Well Lee has just mapped it to 2 BAR on the GTX30 turbo, using M12 head studs and it's made 488 lbft of torque along with 542 bhp!
Is this the highest torque figure for a Zetec now? I know Paul Johnson had more power but can't recall his torque figure?
Mental car anyway, can't wait to see it perfrom.
25-04-2012, 10:53 AM
#3
1/4 mile beasty!!!!
Some impressive power there!!! Did it do any other damage when the head lifted at central day? Should do some good times !!
What's the full spec of the car?
What's the full spec of the car?
25-04-2012, 11:03 AM
#5
Regular Contributor
Join Date: May 2010
Location: London
Posts: 277
Likes: 0
Received 0 Likes
on
0 Posts
Dan rolling road's always make the car look leggy, normally by about 1000 rpm, but on the road it ain't laggy at all!
Yep fingers crossed it should pull some decent times, need to spend some money on suspension now I think! Get some custom coilovers made up!
25-04-2012, 11:06 AM
#6
Dean - Sure Alex can fill in the blanks but 2.1 Zetec, low comps/steel rods, balanced crank, Pace dry sump set up, ported head, Area Six inlet, Devil Developments manifold, GTX30.76 turbo, KMS management, Airtec intercooler and rad, MTX Focus RS gearbox, AP Racing 6-pots.
No other damage, M12 head stud conversion by Lee and back on the dyno!
Next to a M10 ARP:
No other damage, M12 head stud conversion by Lee and back on the dyno!
Next to a M10 ARP:
Last edited by XRT_si; 25-04-2012 at 11:07 AM.
25-04-2012, 11:11 AM
#7
Post Whore
iTrader: (1)
Join Date: Sep 2007
Location: Chingford
Posts: 7,037
Likes: 0
Received 0 Likes
on
0 Posts
Well done Alex...worth all the effort..Bring it Saturday I want a go please...
Trending Topics
25-04-2012, 08:07 PM
#12
Regular Contributor
Join Date: May 2010
Location: London
Posts: 277
Likes: 0
Received 0 Likes
on
0 Posts
26-04-2012, 01:29 PM
#19
Regular Contributor
Join Date: May 2010
Location: London
Posts: 277
Likes: 0
Received 0 Likes
on
0 Posts
26-04-2012, 05:15 PM
#25
Regular Contributor
Join Date: May 2010
Location: London
Posts: 277
Likes: 0
Received 0 Likes
on
0 Posts
Is superflow some sort of race fuel then?
and LOL @ simon, i like that picture lol!
Chip, i dont think it needs to go on the rollers any time soon, so im just going to drive it around for a bit and enjoy it, and just upgrade bits and pieces for now. And go to a few rolling road days lol!
and LOL @ simon, i like that picture lol!
Chip, i dont think it needs to go on the rollers any time soon, so im just going to drive it around for a bit and enjoy it, and just upgrade bits and pieces for now. And go to a few rolling road days lol!
26-04-2012, 06:38 PM
#27
Regular Contributor
Join Date: May 2010
Location: London
Posts: 277
Likes: 0
Received 0 Likes
on
0 Posts
27-04-2012, 09:30 AM
#29
YES I KNOW I CANT SPELL
Join Date: Mar 2008
Location: chingford e4
Posts: 5,271
Likes: 0
Received 0 Likes
on
0 Posts
Is superflow some sort of race fuel then?
and LOL @ simon, i like that picture lol!
Chip, i dont think it needs to go on the rollers any time soon, so im just going to drive it around for a bit and enjoy it, and just upgrade bits and pieces for now. And go to a few rolling road days lol!
and LOL @ simon, i like that picture lol!
Chip, i dont think it needs to go on the rollers any time soon, so im just going to drive it around for a bit and enjoy it, and just upgrade bits and pieces for now. And go to a few rolling road days lol!
Thread
Thread Starter
Forum
Replies
Last Post
