Jim Galbally

Well, after some initial "issues" caused by the supplied wiring digram having the V6 firing order wrong the important bits of my new ECU loom were complete

so we fired her up, AND SHE RUNS!!!!!

woohoo!!!!

cold start is... erm... shit but once she got up to about 20degrees it's happily idle (needs the IWSCV enabling tho, base idle alone aint quite enough)

even did a bit of mapping, she was running very rough, so we took a few ms out of the idle injction site and she ran smooth as a baby's bum i'm now an expert mapper

anyway, she should be ready to pick up next saturday (sun at latest) and i can'twait to drive her with the new ECU, just bliping the throttle at idle is SOOOO much more responsive than it is as standard, hopefully she'll be a bit more lively now


now, do i get her mapped ASAP or do i leave it a bit longer and get the cams fitted 1st (but risk not having the car mapped for the ring)

hmm...

darren.cudd

whats you had fitted then jimbo?

Jim Galbally

Emerald M3DK

AlexF

lovely!

who fitted that for you?

Alex

GARETH T

map it asap,, you dont wanna fuck your engine mate

Jim Galbally

gareth, it comes with a base map from emerald for the V6, but i doubt it'kll be perfect.

i'm thinking of just turning closed loop on and driving it like that till i get the cams in, THEN getting it mapped (as if i get it mapped before the cams i'll need to get it mapped AGAIN afterwards)

Alex,

cossie4i (off here)'s brother Mark he's done LOADS of wiring work on the 24v so was the best choice

GARETH T

do you still travel to swansea? because if you like i could trim the fuel for you if you get stuck

JohnnyB

good lad now the tweaking starts

Munch

nice one

luke89

iTrader: (1)

nice one jim

Jim Galbally

gareth, ive got wideband myself (LM1+XD1 also ECU displays wideband output on live screen, just doesnt have an "autotune" function), but i dont i really want to DIY map (ie "ooh, its rich, ill take some fuel out") especially as i wont have detcans etc!

and no i dont travel to swansea no more

xr4x4rs

iTrader: (5)

cool

what did you do with your old loom mate

Jim Galbally

sprinkled holy water on it then burnt it

the loom was the MAIN reason for upgrading, it was a COMPLETE state!

here you can see the main ECU plug complete with scotchlocked wires (which were linking to the old 2.0 ECU plug!) some twisted together, and just generally, A MESS:


the pic doesnt nearly come close to showing how bad the wiring on my car was

now its all lovely and new and done properly

xr4x4rs

iTrader: (5)

dam lol

was gona ask if you wanted it but if its that bad ill leave it lol
still havnt got a loom yet and im doing the conversion in 2 weeks



does it mater what loom i have aslong its out of a 24v?

Jim Galbally

speak to barry at XR4i spares down in southend (try yell.co.uk for an address) i know he's got a loom, and he doesnt charge topboss prices

dave cos4x4

iTrader: (5)

better to get it mapped before the trip.

can you not get the cams in first then mapped?

Jim Galbally

dave, i gotta take the cams down to kent, get the done (circa 1 week and 300quid) then get the car booked in to have them fitted (few hundred?), then get the car booked in for mapping (200) etc.

oh, and i've got about 500quid to last me a month. (work f**ked up my overtime)

so, if i get all the car stuff done, i cant afford to eat

but i think i'll live dangerously this month and get it all sorted, as next month i get paid 2 lots of overtime, so i'll be minted i might try and extend one of my loans for another 1K, that way i can get it all done in time

Jay,

iTrader: (4)

nice one jim uv joined the standalone crew



cheers jay

Jim Galbally

i'm on hold to egg at the moment, i recon 1.5k should be enough to get the basics done

for the money ive spent on my car i coulda built a 500+bhp esccos

My List of jobs to get done befoer the ring:

1)Buy + Fit Cams
Paint camcovers+plenum
Clean engine bay

2) Change Wheel Bearing
Fit GrpA Fuelpump
Change fuelfilter
Fit new brakes
Fit adjustable TCAs
Fit/Refit silicon hoses

3) Rewire fuel pump
Rewire Alternator
Rewire starter

4) Get wheel welded +refurbed + replace with my bet one!

5) Get the suspension setup

altho thinking about it, thats kinda the only jobs that need doing... ever. after that the car will have NO faults or old niggly bits!!!!!! imagine owning a perfect car! (bugger ive just remembered i need my door repainted coz the paints gone manky, so 99% perfect car...)

dave cos4x4

iTrader: (5)

hope you get it all done for the ring trip Jim.

cars can cost a lot of money sometimes.

cossie4i+

iTrader: (15)

Well done to my little Brother

Hope your pleased Jim.

Steve.

Jim Galbally

steve, we were both jumping for joy when she started and ran

Dan

cossie4i+

iTrader: (15)

You coming over again today Jim ?

How long did it take to sort out the injectors were round the wrong way ?

If so i will get my White 24v XR4i out to show you

Steve.

BillyCabrio

iTrader: (1)

Jim,

I know a nice little garage in Sidcup that give you a hand fitting all that if you need it

https://passionford.com/forum/viewto...845&highlight=

Myself, Lennie, Tony Turbo, TheBishMan all use them

Oh and well done on finally getting ya loom sorted fella

And as for getting ya suspension set-up........GL Coachworks in Sidcup, they are doing mine on the cabbie and Kier's mk1 Escort as we both have adjustable set-up's and they do 4 wheel tracking/alignment

PM B.A.R. mate, you won't regret it

Jim Galbally

ok nice one i'll get on the blower to both

gonna give EGG another ring today, after 58mins on hold lastnight i gave up

mark_24v_wiring

iTrader: (1)

Ok so there was a few problems with the supplyed wiring diagram being a little how shall we say WRONG!!!!!!!

But we got there in the end and i did actually find the correct diagram in amongst all the paper work late last night too but hey it was already sorted

As Jim says the engine seams to rev very quickly if a little bit rich but we sorted that on the idle and had her ticking at about 850rpm smooth as a baby's bum lol now it just need a good mapping session.

Got a few thing left to do today like get the wideband o2 sensor linked up to the ecu and ill sort the fuel pump wiring and the starter too as that seams to have a mind of its own and it will be run up to a proper temp today to make sure the fans work etc then i suppose i had better put the dash back in or maybe i should leave it all on display

What you recon Jim??? ha ha ha ha ha ha

XR4x4RS
As Jim said speek to Barry at the XR4I Spares centre i think he has a spare loom can contact him on 01375672641

The photo Jim posted of his loom really dont do it justice it was a total loss who ever did the wiring in the first place didnt do it very well (yes im being nice can think of a few bad words to say about it !!) If Barry dont have one i may have a spare here but ill have to have a look Failing that get a standalone and ill make you a loom up

Jim Galbally

welcome to passionford mark

now, GET BACK IN THE GARAGE AND FINISH MY CAR

mark_24v_wiring

iTrader: (1)

Errr hmmmm Im thinking abot it lol

Tell you what ill let you know how well she goes down the road later when i Drive it like i stole it LOL ok ok so im joking i may wait for you to come down next week or i may not hmmm maybe we should have a vote who recons i shold drive the car to see what it goes like LOL LOL

That will teach you to make demmands LOL

Jim Galbally

git

anyway, cheque for 1.5K turning up on wednesday, thank you Halifax

ok, so if i'm getting the car back next weekend, i can book the car in for work next week

Garage19

I seem to remember Dave Walker mapping a Cossie 24v that one of his mates had put in a dodgy cortina. It was boggo stock but with better exhaust (and no air flow meter? Do they have one?) and made 230 bhp.

Not bad really. I reckon you could be knockin on the door of 250 bhp wth some cams.

gearboxman

More responsive?
Nice one. If you need any more road tests done, just let me know Jim

Jim Galbally

lol @ bernie

cossie4i+

iTrader: (15)

Fans now work via ECU

Fuel pump rewired

Steve.

cossie4i+

iTrader: (15)

Jim,

Your nearside hose to the rad is not done up and the hose clip is shafted

Steve.

Jim Galbally

steve, i actually know about that, it popped off once, but seems to stay on nicely one of the "to-do" jobs is to get all the hoses re-fitted properly and with new clips

heard from mark earlier, aparently all thats left is to put the dash back together

having trouble with the LC-1 (wideband controller) tho, however ive just been reading and re-reading the manual and ive come across some things to sugest it'll need a bit more seting up before it works properly, but its no biggie, just means it needs to be plugged into the laptop and set up

cossie4i+

iTrader: (15)

Can i have that hose that fits on the plenum elbow please

Steve.

Jim Galbally

yes, WHEN MY NEW ONE TURNS UP FROM MIKE

cossie4i+

iTrader: (15)

Thank You

Steve.

James-W

Cool bro.
You fitting a supper dooper charger or you decided agaist that?