stickers how do i go about doing them
17-02-2004, 09:35 PM
#1
stickers how do i go about doing them
As above my s1 has had a full respary any need a put the tranceferes on 
whots the best way to do this as i want to get them right 
Has anyone done any on a s1 in the pasted 
whots the best way to do this as i want to get them right Has anyone done any on a s1 in the pasted
18-02-2004, 10:41 AM
#3
Originally Posted by BlackS2
Get a bodyshop to do it mate, then u can blame them if they fuck it up, lol
18-02-2004, 12:14 PM
#4
Get a Sign writing place to do it as they always have someone who goes round car show rooms and businesses putting them up.
Don't do it yourself as everywhere you go you'll get someone point out that they aren't straight or they have a bubble in there etc.
Don't do it yourself as everywhere you go you'll get someone point out that they aren't straight or they have a bubble in there etc.
18-02-2004, 12:48 PM
#5
Originally Posted by cliff6732000
Get a Sign writing place to do it as they always have someone who goes round car show rooms and businesses putting them up.
Don't do it yourself as everywhere you go you'll get someone point out that they aren't straight or they have a bubble in there etc.
Don't do it yourself as everywhere you go you'll get someone point out that they aren't straight or they have a bubble in there etc.
22-02-2004, 06:11 PM
#7
Hello mate done two, one 1600i and 0ne S1.
Clean all traces of wax off panel. Mix up some soapy water, I used washing up liquid. Wet the area of the car you are applying to. Get someone to hold one end of the transfer, you hold the end first being applied. The soapy water enables you to slide it around to get position correct before it sticks. Once in place, hold the end you are going to start with, so as it don't move. Use a credit card or new filler spreader, rubbers good, make sure no sharp edges and squegy the water towards the end of the transfer. It's really easy, but take your time with it. Go over the squegy process several times, the first time is the worst because you have to be careful not to crease it and to get any bubbles out. That's how proffessionals do it.
Clean all traces of wax off panel. Mix up some soapy water, I used washing up liquid. Wet the area of the car you are applying to. Get someone to hold one end of the transfer, you hold the end first being applied. The soapy water enables you to slide it around to get position correct before it sticks. Once in place, hold the end you are going to start with, so as it don't move. Use a credit card or new filler spreader, rubbers good, make sure no sharp edges and squegy the water towards the end of the transfer. It's really easy, but take your time with it. Go over the squegy process several times, the first time is the worst because you have to be careful not to crease it and to get any bubbles out. That's how proffessionals do it.
Trending Topics
22-02-2004, 08:41 PM
#8
thers lots of diffrent ways .i put me own on me s1
i put masking tape at the top of the stripe when i was
happy that they were straitght. then lifted up the stripe
with tape still in place and peeled back the backing paper.
and presto
i put masking tape at the top of the stripe when i was
happy that they were straitght. then lifted up the stripe
with tape still in place and peeled back the backing paper.
and presto
the S1 is in essex at mum and dad and i have'nt got the engine back yet 
Thread
Thread Starter
Forum
Replies
Last Post
RB26DETT
General Car Related Discussion.
17
27-05-2016 11:26 AM
borboyous
Cars for Sale
6
22-08-2015 11:17 AM