Peugeot 205 with 4wd cosworth engine and running gear.
#2081
10K+ Poster!!
My car will be much lighter and will not get anywhere near the abuse of regular pod launches. I doubt my 2.2 will produce any more torque as I will not run much over 600bhp.
#2082
PassionFord Post Troll
Not sure mate I asked him he told me front and rear quaffe mate oppligger 6 speed seq mark will now he's tuned it
#2083
**RS COSWORTH**
Jons was the first efr cossie I been in was running 500bhp+. That's what got be believing how good they could drive setup right.
#2084
10K+ Poster!!
It might have the stronger 3.9 and if he has 3.9 rear diff then no need for drop gears...I do not know how much stronger the 3.9 is over 3.6...I think Jay referred to the 3.6 as "chocolate"
#2085
PassionFord Post Troll
Good to know they do it in a 3.9 I won't need drop gears then r+d aswell?
#2087
cossie fan (unluckerly)
Did you go in it with a 9180 on it? I really need go in one with the big turbo. The same engine spec is going in mine bar a few differences
Last edited by ajamesc; 16-05-2018 at 04:16 PM.
#2088
**RS COSWORTH**
#2089
PassionFord Post Whore!!
Mark
#2090
1st to 200 without NOS
iTrader: (2)
Hi, I have a quaife ATB 3.6 in the front with strengthening plate, plus I use the 2 support brackets to help support it on the block....bara said that the weak point is the crown wheel and pinion...if it breaks I will stick a 3.9 R&D in it and add drop gears to the oppliger box.
#2091
10K+ Poster!!
Never mind, if I break the cwp, the atb should be fine to sell on and I will buy a big diff.
#2093
PassionFord Post Troll
Ahmed tried to switch me on to that engine instead of the cossie said it makes lots of torque very easily
#2094
10K+ Poster!!
That’s a lovely Engine, loved by many people and makes the right noises.
The following users liked this post:
visa_broke (17-05-2018)
#2096
10K+ Poster!!
Bum, I let an rnd go as thought my box would need to come apart
#2097
10K+ Poster!!
Nice set of billet pulleys arrived, I will post up the other ones Mark sent me (Thank You)
#2098
10K+ Poster!!
T45 WRC cradle to MK spec. Nice to see it in the car. I cannot wait to drive it.
#2100
10K+ Poster!!
I am having the T45 one that I posted up, I think this one is used for the Mock Up as the location points are all the same...will check with Mark though.
#2101
10K+ Poster!!
The one in the last pic was just the mock up Marc. How’s your car doing? Not seen you on here for a while.
#2103
10K+ Poster!!
#2105
10K+ Poster!!
My props have already been done but with a brand new tunnel and new gearbox mount we need to make sure then1 inch extra is catered for...also my shell is already non standard so 22 cm shorter.
#2106
10K+ Poster!!
Boot floor is largely staying, will have a hump to allow exhaust to pass over cradle, Mark has chopped out the little coil over boxes and repaired the arch ready to chop out for the massive WRC turrets. You can see the pick up points where the cage will meet cradle mounts.
#2108
10K+ Poster!!
T45 cradle taking shape, Mark has made a lot of Gucci mods to allow the diff to come out easily. Supra diff plug n play
I love the little lugs here to hold the diff
#2109
**RS COSWORTH**
Looking very good. Have you decided on what colour it's all going including the car.
#2110
10K+ Poster!!
I think car will stay red, I will strip anything left underneath and have that body colour and then powder coat things like the cradle in (most likely) black.
#2111
PassionFord Post Troll
Nice mate
The following users liked this post:
Caddyshack (26-05-2018)
#2112
Advanced PassionFord User
I have had stuff powder coated in the past but I'm not sure i'd do it again, on another forum I'm on people was finding stones etc would damage the powder coat and let water get underneath and rust. I need to start looking into getting an alternative coat of something again when I start doing the 944.
#2113
10K+ Poster!!
I think you do need to be certain the powder is good. I spoke to my painter and he said powder was harder wearing than paint. Interested if there are other options.
I don’t mind re-doing every so often I suppose.
I don’t mind re-doing every so often I suppose.
#2114
**RS COSWORTH**
2 pack epoxy primer over powder coating underside compents.
The following users liked this post:
Caddyshack (26-05-2018)
#2116
10K+ Poster!!
iTrader: (9)
The fiesta is good, took it for its MOT last saterday, first time its been driven since I took it to my wedding last August !
May end up putting it up for sale as I never use it and see what happens but it will be big money so who knows
#2117
10K+ Poster!!
I think you will regret selling it, just wait for life to settle down. I regret a few sales, I sold through lack of use but would use a lot more now. Use it more and you will love it, change anything that annoys.
The following users liked this post:
Caddyshack (27-05-2018)
#2119
10K+ Poster!!
A bit of the cage has gone in to tie up the cradle mounts, the square bars are just bracing whilst the floor is out.