C&B's 350bhp CVH RST BREAKING - See for sale section
#81
![Default](https://passionford.com/forum/images/icons/icon1.gif)
I started assembling the Cylinder Head today. This process is very time-consuming, but cannot be rushed. This is what was done......
![Name: HeadBuild001.jpg
Views: 656
Size: 45.1 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146397d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild001.jpg)
Once the Valve is fitted, the 'Installed height' is measured and adjusted using Shims......
![Name: HeadBuild002.jpg
Views: 641
Size: 43.6 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146398d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild002.jpg)
.....before fitting the Valve Stem Oil Seals......
![Name: HeadBuild003.jpg
Views: 820
Size: 46.7 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146399d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild003.jpg)
Then the Double Valve Springs are fitted with the Special Retainers.......
![Name: HeadBuild004.jpg
Views: 651
Size: 66.8 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146400d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild004.jpg)
![Name: HeadBuild005.jpg
Views: 636
Size: 62.9 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146401d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild005.jpg)
![Name: HeadBuild006.jpg
Views: 635
Size: 56.4 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146402d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild006.jpg)
![Name: HeadBuild007.jpg
Views: 647
Size: 76.6 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146403d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild007.jpg)
![Name: HeadBuild008.jpg
Views: 644
Size: 77.5 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146404d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild008.jpg)
I have also prepared the Block and Main Bearing Caps ready for the next installment.
![Name: HeadBuild001.jpg
Views: 656
Size: 45.1 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146397d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild001.jpg)
Once the Valve is fitted, the 'Installed height' is measured and adjusted using Shims......
![Name: HeadBuild002.jpg
Views: 641
Size: 43.6 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146398d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild002.jpg)
.....before fitting the Valve Stem Oil Seals......
![Name: HeadBuild003.jpg
Views: 820
Size: 46.7 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146399d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild003.jpg)
Then the Double Valve Springs are fitted with the Special Retainers.......
![Name: HeadBuild004.jpg
Views: 651
Size: 66.8 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146400d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild004.jpg)
![Name: HeadBuild005.jpg
Views: 636
Size: 62.9 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146401d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild005.jpg)
![Name: HeadBuild006.jpg
Views: 635
Size: 56.4 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146402d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild006.jpg)
![Name: HeadBuild007.jpg
Views: 647
Size: 76.6 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146403d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild007.jpg)
![Name: HeadBuild008.jpg
Views: 644
Size: 77.5 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146404d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headbuild008.jpg)
I have also prepared the Block and Main Bearing Caps ready for the next installment.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Smokin](https://passionford.com/forum/images/smilies/icon_smokin.gif)
#82
PassionFord Post Whore!!
Join Date: May 2003
Location: Isle of Wight
Posts: 4,723
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Christian is that something you should to every cylinder head when rebuilding it?
Might be a good thing to do to mine when I get it back, where would you get the shims from?
Might be a good thing to do to mine when I get it back, where would you get the shims from?
#86
![Default](https://passionford.com/forum/images/icons/icon1.gif)
We are trying to fit in building this engine with the fact that we have little time to spare at the moment!!
The crank is now fitted.
Once the block was thoroughly cleaned and blown out with a High Pressure Airline, including all the Oilways etc, the crank was thoroughly cleaned and again, the Oilways were blown through.
The Main Bearings were then cleaned to remove any treatment that was applied to them at the factory and they were laid into place. The Main Caps were then put on to check that the Groove's lined up. Once this was all satisfactory, the Caps were removed and the Crank put into place, after which the Main Caps were fitted.
The Bearing Tolerances are checked using 'Plastiguage'......
![Name: CrankFitting001.jpg
Views: 628
Size: 59.5 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146405d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-crankfitting001.jpg)
The Main Caps are all Torque'd down in 2 stages.......
![Name: CrankFitting002.jpg
Views: 617
Size: 80.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146406d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-crankfitting002.jpg)
....before the whole assembly is dismantled to check the Tolerance.......
![Name: CrankFitting003.jpg
Views: 605
Size: 69.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146407d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-crankfitting003.jpg)
......using the Chart.
![Name: CrankFitting004.jpg
Views: 630
Size: 42.8 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146408d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-crankfitting004.jpg)
The End Float of the Crank was also checked using a DTI.
![Name: CrankFitting005.jpg
Views: 610
Size: 38.9 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146409d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-crankfitting005.jpg)
Hopefully the weekend should see the Pistons in place.
The crank is now fitted.
Once the block was thoroughly cleaned and blown out with a High Pressure Airline, including all the Oilways etc, the crank was thoroughly cleaned and again, the Oilways were blown through.
The Main Bearings were then cleaned to remove any treatment that was applied to them at the factory and they were laid into place. The Main Caps were then put on to check that the Groove's lined up. Once this was all satisfactory, the Caps were removed and the Crank put into place, after which the Main Caps were fitted.
The Bearing Tolerances are checked using 'Plastiguage'......
![Name: CrankFitting001.jpg
Views: 628
Size: 59.5 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146405d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-crankfitting001.jpg)
The Main Caps are all Torque'd down in 2 stages.......
![Name: CrankFitting002.jpg
Views: 617
Size: 80.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146406d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-crankfitting002.jpg)
....before the whole assembly is dismantled to check the Tolerance.......
![Name: CrankFitting003.jpg
Views: 605
Size: 69.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146407d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-crankfitting003.jpg)
......using the Chart.
![Name: CrankFitting004.jpg
Views: 630
Size: 42.8 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146408d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-crankfitting004.jpg)
The End Float of the Crank was also checked using a DTI.
![Name: CrankFitting005.jpg
Views: 610
Size: 38.9 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146409d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-crankfitting005.jpg)
Hopefully the weekend should see the Pistons in place.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
#90
PassionFord Post Troll
Join Date: Apr 2004
Location: Kent
Posts: 2,865
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
![Clap](https://passionford.com/forum/images/smilies/9c-clap.gif)
Christian, why do you use shims under the valve stem oil seal?
Does that not lift the valve stem oil seal up higher causing contact between the spring retainer and the seal when the valve is on full lift?
I see no use for them other than compressing the springs a further 0.5mm.
Don't mean to sound as though i'm "Nit-picking", its a genuine querry as i'm thinking of changing some of my cam gear.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
Matt.
#92
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Originally Posted by zvhturbo
![Clap](https://passionford.com/forum/images/smilies/9c-clap.gif)
Christian, why do you use shims under the valve stem oil seal?
Does that not lift the valve stem oil seal up higher causing contact between the spring retainer and the seal when the valve is on full lift?
I see no use for them other than compressing the springs a further 0.5mm.
Don't mean to sound as though i'm "Nit-picking", its a genuine querry as i'm thinking of changing some of my cam gear.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
Matt.
HTH.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
#93
Advanced PassionFord User
Join Date: May 2003
Location: Workin on the car , or workin the missus
Posts: 2,442
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
good work fella ,
i wish i had the time to start my new one , might pull my finger out at the end of the year and have it done for brunters ,
i want 161mph ,
Hat off tho mate , 1600 8 valve , outstanding .
i wish i had the time to start my new one , might pull my finger out at the end of the year and have it done for brunters ,
i want 161mph ,
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
Hat off tho mate , 1600 8 valve , outstanding .
#95
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Today, we finally got the Pistons in, after Filing and Fitting the Piston Rings (which is a very time-consuming task!!). Here you can see the block with the Oil Pump in place and the Head Gasket on........
![Name: HeadGasketOn.jpg
Views: 662
Size: 99.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146410d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headgasketon.jpg)
![Name: HeadGasketOn002.jpg
Views: 633
Size: 76.8 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146411d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headgasketon002.jpg)
Then the Head was laid on......
![Name: HeadOn.jpg
Views: 623
Size: 76.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146412d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headon.jpg)
.....and the Head bolts fitted and Torque'd down......
![Name: HeadBoltsIn.jpg
Views: 599
Size: 77.7 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146413d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headboltsin.jpg)
Then the new Head > Exhaust Studs were fitted.....
![Name: HeadExhaustStuds001.jpg
Views: 607
Size: 77.1 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146414d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headexhauststuds001.jpg)
![Name: HeadExhaustStuds002.jpg
Views: 622
Size: 68.7 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146415d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headexhauststuds002.jpg)
I also did a bit more painting and need to order some bits from Ford, but it is really starting to take shape. The Baffled Sump is ready to fit, this will go on tomorrow or Saturday, as will the Exhaust Manifold and Turbo.
I have also just had my Inlet/Injector Plate/Rocker Cover and Fuel Rail back from being Painted. I'm not sure if I am going to post pics of that though, at this stage. Suffice to say, I am VERY pleased with how it has come out.
![Name: HeadGasketOn.jpg
Views: 662
Size: 99.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146410d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headgasketon.jpg)
![Name: HeadGasketOn002.jpg
Views: 633
Size: 76.8 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146411d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headgasketon002.jpg)
Then the Head was laid on......
![Name: HeadOn.jpg
Views: 623
Size: 76.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146412d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headon.jpg)
.....and the Head bolts fitted and Torque'd down......
![Name: HeadBoltsIn.jpg
Views: 599
Size: 77.7 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146413d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headboltsin.jpg)
Then the new Head > Exhaust Studs were fitted.....
![Name: HeadExhaustStuds001.jpg
Views: 607
Size: 77.1 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146414d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headexhauststuds001.jpg)
![Name: HeadExhaustStuds002.jpg
Views: 622
Size: 68.7 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146415d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-headexhauststuds002.jpg)
I also did a bit more painting and need to order some bits from Ford, but it is really starting to take shape. The Baffled Sump is ready to fit, this will go on tomorrow or Saturday, as will the Exhaust Manifold and Turbo.
I have also just had my Inlet/Injector Plate/Rocker Cover and Fuel Rail back from being Painted. I'm not sure if I am going to post pics of that though, at this stage. Suffice to say, I am VERY pleased with how it has come out.
![Content](https://passionford.com/forum/images/smilies/content.gif)
![Smokin](https://passionford.com/forum/images/smilies/icon_smokin.gif)
#104
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Originally Posted by Freddy_mercury_magic
Christian and Beccy, is there a reason why you havent taken pictures of the inlets side of the head
or can we not see it?
Also how hard is taking a cvh head apart
Thanks Radleigh![Big Grin](https://passionford.com/forum/images/smilies/icon_biggrin.gif)
![Confused](https://passionford.com/forum/images/smilies/icon_confused.gif)
or can we not see it?
Also how hard is taking a cvh head apart
![Confused](https://passionford.com/forum/images/smilies/icon_confused.gif)
Thanks Radleigh
![Big Grin](https://passionford.com/forum/images/smilies/icon_biggrin.gif)
![Wink](https://passionford.com/forum/images/smilies/icon_wink.gif)
As for taking a CVH head apart, it isn't really hard as long as you know what you are doing, but takes a while.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
Originally Posted by zvhturbo
Looking good chaps
How comes youv'e not gone for a wire rung block and lower compression if your looking to run big boost
??
![Clap](https://passionford.com/forum/images/smilies/9c-clap.gif)
How comes youv'e not gone for a wire rung block and lower compression if your looking to run big boost
![Confused](https://passionford.com/forum/images/smilies/icon_confused.gif)
Infact, it is Low Compression, but not really sure what makes you think it isn't??
![Wink](https://passionford.com/forum/images/smilies/icon_wink.gif)
#111
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Originally Posted by Tony Turbo
Originally Posted by Christian and Beccy
Hoping to plonk it back in the hole over the weekend.
Fantastic news mate
![Clap](https://passionford.com/forum/images/smilies/9c-clap.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
Originally Posted by Lee @ Fusion
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
beat me to it
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Wink](https://passionford.com/forum/images/smilies/icon_wink.gif)
#114
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Update time!!
After a slight alteration to the Downpipe as it sat a little low, I wrapped it with Heatproof Wrap. The smaller of the 2 Bosses is for Exhaust Gas Temperature and the larger one is for the Lambda Sensor (We run a Wideband Sensor in there for mapping and eventually the Omex will require a sensor in there permanently).
![Name: Downpipe001.jpg
Views: 611
Size: 135.9 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146416d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-downpipe001.jpg)
![Name: Downpipe002.jpg
Views: 622
Size: 131.5 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146417d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-downpipe002.jpg)
![Name: Downpipe003.jpg
Views: 598
Size: 104.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146418d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-downpipe003.jpg)
The Wrap is a Double layer where is runs close to the Alternator and Starter Motor and continues to just beyond the Driveshafts.......
![Name: Downpipe004.jpg
Views: 617
Size: 72.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146419d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-downpipe004.jpg)
![Name: Downpipe005.jpg
Views: 625
Size: 66.9 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146420d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-downpipe005.jpg)
More to follow........
After a slight alteration to the Downpipe as it sat a little low, I wrapped it with Heatproof Wrap. The smaller of the 2 Bosses is for Exhaust Gas Temperature and the larger one is for the Lambda Sensor (We run a Wideband Sensor in there for mapping and eventually the Omex will require a sensor in there permanently).
![Name: Downpipe001.jpg
Views: 611
Size: 135.9 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146416d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-downpipe001.jpg)
![Name: Downpipe002.jpg
Views: 622
Size: 131.5 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146417d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-downpipe002.jpg)
![Name: Downpipe003.jpg
Views: 598
Size: 104.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146418d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-downpipe003.jpg)
The Wrap is a Double layer where is runs close to the Alternator and Starter Motor and continues to just beyond the Driveshafts.......
![Name: Downpipe004.jpg
Views: 617
Size: 72.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146419d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-downpipe004.jpg)
![Name: Downpipe005.jpg
Views: 625
Size: 66.9 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146420d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-downpipe005.jpg)
More to follow........
![Smokin](https://passionford.com/forum/images/smilies/icon_smokin.gif)
#116
![Default](https://passionford.com/forum/images/icons/icon1.gif)
I have opted for a slightly different Inlet Manifold. There were a number of different reasons for this. It was very hard to adapt it to fit. The Throttle Body mounting had to be completely altered and adjusted to point at a more appropriate angle........
![Name: InletManifold001.jpg
Views: 640
Size: 102.9 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146422d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-inletmanifold001.jpg)
![Name: InletManifold002.jpg
Views: 613
Size: 160.4 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146423d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-inletmanifold002.jpg)
Obviously, with the lack of Inlet Crossover Pipe, I could then use a boggo CVH Rocker Cover.......
![Name: RockerCover002.jpg
Views: 786
Size: 90.4 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146424d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-rockercover002.jpg)
![Name: InletManifold001.jpg
Views: 640
Size: 102.9 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146422d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-inletmanifold001.jpg)
![Name: InletManifold002.jpg
Views: 613
Size: 160.4 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146423d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-inletmanifold002.jpg)
Obviously, with the lack of Inlet Crossover Pipe, I could then use a boggo CVH Rocker Cover.......
![Name: RockerCover002.jpg
Views: 786
Size: 90.4 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146424d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-rockercover002.jpg)
![Content](https://passionford.com/forum/images/smilies/content.gif)
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
#118
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Here is the engine in place and 95% finished. I just have a few loose ends to tie up.
I started to fabricate a Throttle Cable bracket today and have an Inlet Pipe on its way from Pro Alloy. I also have a remote Fuel Pressure Regulator to fit.
![Name: EngineBay001.jpg
Views: 635
Size: 85.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146425d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-enginebay001.jpg)
![Name: EngineBay002.jpg
Views: 633
Size: 93.3 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146426d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-enginebay002.jpg)
Here you can see the Injector mounting and the spangly wiring loom braiding. Man, that was time consuming!!
![Name: EngineBay003.jpg
Views: 610
Size: 97.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146427d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-enginebay003.jpg)
Hoping to turn the key over the weekend.....
I started to fabricate a Throttle Cable bracket today and have an Inlet Pipe on its way from Pro Alloy. I also have a remote Fuel Pressure Regulator to fit.
![Name: EngineBay001.jpg
Views: 635
Size: 85.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146425d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-enginebay001.jpg)
![Name: EngineBay002.jpg
Views: 633
Size: 93.3 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146426d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-enginebay002.jpg)
Here you can see the Injector mounting and the spangly wiring loom braiding. Man, that was time consuming!!
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Name: EngineBay003.jpg
Views: 610
Size: 97.2 KB](https://passionford.com/forum/attachments/restorations-rebuilds-and-projects/146427d1502131792-c-and-b-s-350bhp-cvh-rst-breaking-see-for-sale-section-enginebay003.jpg)
Hoping to turn the key over the weekend.....
![Content](https://passionford.com/forum/images/smilies/content.gif)
![Big Grin](https://passionford.com/forum/images/smilies/icon_mrgreen.gif)
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
#119
www.ctuceilings.co.uk
Join Date: May 2003
Location: Kent
Posts: 9,370
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
SEXUAL!!!
Liking it alot. Finally all those MONTHS of hard work on that inlet manifold have payed off. I remember you starting that when my other engine was still being mapped
Looks the bollox mate, and to do it all yourself.......
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
Liking it alot. Finally all those MONTHS of hard work on that inlet manifold have payed off. I remember you starting that when my other engine was still being mapped
![Surprised](https://passionford.com/forum/images/smilies/shocked.gif)
![Big Grin](https://passionford.com/forum/images/smilies/icon_mrgreen.gif)
Looks the bollox mate, and to do it all yourself.......
![Smokin](https://passionford.com/forum/images/smilies/icon_smokin.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)