Escort RST Zetec Turbo Build - UPDATE 02/07/11 - Bodywork/pedal box
He always does mate, treats them like they were his own!
06-05-2011, 05:46 PM
#127
I've found that life I needed.. It's HERE!!
Thread Starter
iTrader: (1)
Join Date: Mar 2009
Location: Portsmouth
Posts: 1,377
Likes: 0
Received 0 Likes
on
0 Posts
Small Update,
Now got a Corbeau Revolution seat and got the Vipec management that was on the engine i bought, thanks to Liams as got it for a very good price
Apart from that not alot of progress has been made.
Now got a Corbeau Revolution seat and got the Vipec management that was on the engine i bought, thanks to Liams as got it for a very good price
Apart from that not alot of progress has been made.
07-06-2011, 07:47 PM
#133
I've found that life I needed.. It's HERE!!
Thread Starter
iTrader: (1)
Join Date: Mar 2009
Location: Portsmouth
Posts: 1,377
Likes: 0
Received 0 Likes
on
0 Posts
Small Update.
Not much done as of late. Got a bit done today thought, thought i would tackle some of the bodywork. Loz (Danster76's mate) is doing all the main bodywork like arches sills etc but i gave some of the small stuff ago. Not welded long and never done any bodywork before so here it goes!! Few pics.
Plated the hole for the loom as it now goes through the wheel arch.
Then tackled the rot at the rear of the drivers side floor pan.
Thats as far as i got this evening will finish off during the week.
Not much done as of late. Got a bit done today thought, thought i would tackle some of the bodywork. Loz (Danster76's mate) is doing all the main bodywork like arches sills etc but i gave some of the small stuff ago. Not welded long and never done any bodywork before so here it goes!! Few pics.
Plated the hole for the loom as it now goes through the wheel arch.
Then tackled the rot at the rear of the drivers side floor pan.
Thats as far as i got this evening will finish off during the week.
02-07-2011, 03:24 PM
#135
I've found that life I needed.. It's HERE!!
Thread Starter
iTrader: (1)
Join Date: Mar 2009
Location: Portsmouth
Posts: 1,377
Likes: 0
Received 0 Likes
on
0 Posts
Right then bit of an update!
Car went off to Loz for the welding. Hes done the drivers side so far, inner and outer rear arches and the sill. Sorry about the poor pics off the iphone.
Old arches cut out.
New arches fitted!
Loz having a cracking time!!
Also this was waiting for me after work yesterday, just trial fitted in there looks the part!!
Thats it for now, the other side should be done by next weekend.
Car went off to Loz for the welding. Hes done the drivers side so far, inner and outer rear arches and the sill. Sorry about the poor pics off the iphone.
Old arches cut out.
New arches fitted!
Loz having a cracking time!!
Also this was waiting for me after work yesterday, just trial fitted in there looks the part!!
Thats it for now, the other side should be done by next weekend.
05-09-2011, 04:56 PM
#145
I've found that life I needed.. It's HERE!!
Thread Starter
iTrader: (1)
Join Date: Mar 2009
Location: Portsmouth
Posts: 1,377
Likes: 0
Received 0 Likes
on
0 Posts
Studabear - Not 100% sure if your running a standard BC box but when running a FRS box you have to chop both inner wings (LH and RH). Also im going dry sump so i need all the room i can get!!
Jonny - Yeh slowly getting there, lost alot of intrest at the moment due to getting back into my cycling but once the bad weather is here ill crack on with it again. Defo get yours finished mate! From what i remember i was a nice little spec?
Jonny - Yeh slowly getting there, lost alot of intrest at the moment due to getting back into my cycling but once the bad weather is here ill crack on with it again. Defo get yours finished mate! From what i remember i was a nice little spec?
05-09-2011, 04:58 PM
#146
I've found that life I needed.. It's HERE!!
Thread Starter
iTrader: (1)
Join Date: Mar 2009
Location: Portsmouth
Posts: 1,377
Likes: 0
Received 0 Likes
on
0 Posts
Davey Saff - No real progress if im honest, brought a roll over jig so just need to weld it up and get the car over so i can restore the underside. Apart from that brought a mint 1600i front ARB.
05-09-2011, 05:04 PM
#147
id finished the grey track car long ago,
but my long term 16v turbo(moonstone) with smoothed bay and peddle box etc....aint gunna be finished, ive far too much on me hands atm so will have to let that go to a good home
wrap up in the cold and get it finished i cant wait to see yours done
but my long term 16v turbo(moonstone) with smoothed bay and peddle box etc....aint gunna be finished, ive far too much on me hands atm so will have to let that go to a good home
wrap up in the cold and get it finished i cant wait to see yours done
05-09-2011, 05:22 PM
#148
I've found that life I needed.. It's HERE!!
Thread Starter
iTrader: (1)
Join Date: Mar 2009
Location: Portsmouth
Posts: 1,377
Likes: 0
Received 0 Likes
on
0 Posts
id finished the grey track car long ago,
but my long term 16v turbo(moonstone) with smoothed bay and peddle box etc....aint gunna be finished, ive far too much on me hands atm so will have to let that go to a good home
wrap up in the cold and get it finished i cant wait to see yours done
but my long term 16v turbo(moonstone) with smoothed bay and peddle box etc....aint gunna be finished, ive far too much on me hands atm so will have to let that go to a good home
wrap up in the cold and get it finished i cant wait to see yours done
Thread
Thread Starter
Forum
Replies
Last Post
Cameron
General Car Related Discussion.
14
09-08-2015 06:28 AM
