Track saphhire
#241
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
I sold the stage 3 rear beam and took a standard beam and arms over to scs to get one of there beams,Then with standard style rear arms I at least can fit the bladed a/r/b links and have somewhere the weld the brackets to the arms
Mounted the oil cooler to the n/s space behind the bumper and routed the pipe work up nice
And have been pissing about with a celica breather system that just need a bracket or two to fit nice and a -10 fitting welded on to suit the three pipes on a cossie
Pic on celice st165
Will need to be painted after welding but will fit nice
Mounted the oil cooler to the n/s space behind the bumper and routed the pipe work up nice
And have been pissing about with a celica breather system that just need a bracket or two to fit nice and a -10 fitting welded on to suit the three pipes on a cossie
Pic on celice st165
Will need to be painted after welding but will fit nice
Last edited by Brettski mk2; 10-06-2011 at 02:44 PM.
#242
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
Need to get the drain bung moved on the bottom to the side and one more -10 fitting welded on but it fits ok
mounted the filter housing and cooler
Anyone able to tell me what size the fittinf is in the turbo? turbo side is 1/8 NPT and the hose side I think is bsp but ....?
mounted the filter housing and cooler
Anyone able to tell me what size the fittinf is in the turbo? turbo side is 1/8 NPT and the hose side I think is bsp but ....?
#244
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
Hi Ronnie
The bolts are these m14x70mm 12.9
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=300367077302&ssPageNam e=STRK:MEWAX:IT
m14 with 14mm hole Rod ends
http://cgi.ebay.co.uk/M14-Female-RH-HIGH-PERFORMANCE-Rose-Joint-14mm-ROD-END-/380276945917?pt=UK_CarsParts_Vehicles_CarParts_SM& hash=item588a45b3fd
And my mate made me some spacers up keeping the steering arms the same angle as the lower arm...may need to tweek the spacer hight
The bolts are these m14x70mm 12.9
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=300367077302&ssPageNam e=STRK:MEWAX:IT
m14 with 14mm hole Rod ends
http://cgi.ebay.co.uk/M14-Female-RH-HIGH-PERFORMANCE-Rose-Joint-14mm-ROD-END-/380276945917?pt=UK_CarsParts_Vehicles_CarParts_SM& hash=item588a45b3fd
And my mate made me some spacers up keeping the steering arms the same angle as the lower arm...may need to tweek the spacer hight
Last edited by Brettski mk2; 21-05-2011 at 07:54 PM.
#246
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
Hi its nealy finished mate
He needs a rad and rear brake pads,fit the front bumper,bleed brakes up,fit the extaust new front wheel bearings that sort of stuff
He is a bit slow now ...and hes so close to finishing it
He needs a rad and rear brake pads,fit the front bumper,bleed brakes up,fit the extaust new front wheel bearings that sort of stuff
He is a bit slow now ...and hes so close to finishing it
#247
PassionFord Post Whore!!
iTrader: (17)
Join Date: May 2004
Posts: 5,618
Likes: 0
Received 0 Likes
on
0 Posts
Hi Ronnie
The bolts are these m14x70mm 12.9
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=300367077302&ssPageNam e=STRK:MEWAX:IT
m14 with 14mm hole Rod ends
http://cgi.ebay.co.uk/M14-Female-RH-HIGH-PERFORMANCE-Rose-Joint-14mm-ROD-END-/380276945917?pt=UK_CarsParts_Vehicles_CarParts_SM& hash=item588a45b3fd
And my mate made me some spacers up keeping the steering arms the same angle as the lower arm...may need to tweek the spacer hight
The bolts are these m14x70mm 12.9
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=300367077302&ssPageNam e=STRK:MEWAX:IT
m14 with 14mm hole Rod ends
http://cgi.ebay.co.uk/M14-Female-RH-HIGH-PERFORMANCE-Rose-Joint-14mm-ROD-END-/380276945917?pt=UK_CarsParts_Vehicles_CarParts_SM& hash=item588a45b3fd
And my mate made me some spacers up keeping the steering arms the same angle as the lower arm...may need to tweek the spacer hight
cool, thanks for the links mate, RE the spacers are they tapered to fit into the arm on the hub?
love the car by the way
#248
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
I have the alloy uprights and the bolt on arms have M14 hole in so just tapered the top to allow the rod end the move
I ll get a pic of the spacer soon
I ll get a pic of the spacer soon
#251
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
Got the front all on now and it can stay on this time and orded a new wind screen,the dash is off to autoflock for flocking next week.
I have orded a SCS 6 degree beam so when I get that it will be rolling!!!
I need check straps on all 4 corners as when you jack the car up the shocks hang to low and try to pull the front drive shafts out
bit of Carbon
I have orded a SCS 6 degree beam so when I get that it will be rolling!!!
I need check straps on all 4 corners as when you jack the car up the shocks hang to low and try to pull the front drive shafts out
bit of Carbon
#257
Too many posts.. I need a life!!
#260
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
Got the dash flocked by Raj at autoflock looks well
Had to make a new pas pump feed pipe because the grp A roll bar hit the ford one!
And got a full coner built up and sorted
Had to make a new pas pump feed pipe because the grp A roll bar hit the ford one!
And got a full coner built up and sorted
#265
Wahay!! I've lost my Virginity!!
Nice
Nice project !! What Shocks are you using ?
Have the ahmed bayjoo/scs rear beam better clearance that adrenaline ? or what is the problem for change from adrenaline stage 3 to scs ?
Best Regards
Have the ahmed bayjoo/scs rear beam better clearance that adrenaline ? or what is the problem for change from adrenaline stage 3 to scs ?
Best Regards
#266
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
adrenaline stage 3 needed modifications to the body and I don't think the trailing arm are strong enough,there strong enough not to brake just twist and flex in the corners
hth
#271
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
I,m up to my neck in suspension problems now fucking car and nearly want to break it!!
Ohlins shocks are to long so need to lower the car over them to get the shock travel right just as tony from "tcs" told me I would understand what you mean now tony
So I now have to cut the newly painted suspension turrets off and raise them up. should I go wrc top mounts of weld a ring in to the turret and still use the grp a top mount! ....how do you calculate the amount you need to raise them by ...help"Tony"
Fooking hate this car now and when its finished I will thrash the fooking thing round ford fair like a rally stage!!!!kill hate kill hate!!!!laying rubber until I'm told off
Ohlins shocks are to long so need to lower the car over them to get the shock travel right just as tony from "tcs" told me I would understand what you mean now tony
So I now have to cut the newly painted suspension turrets off and raise them up. should I go wrc top mounts of weld a ring in to the turret and still use the grp a top mount! ....how do you calculate the amount you need to raise them by ...help"Tony"
Fooking hate this car now and when its finished I will thrash the fooking thing round ford fair like a rally stage!!!!kill hate kill hate!!!!laying rubber until I'm told off
#273
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
I have the grp a top mounts
I will cut the top off neat and weld a ring in lift the mount up so the bonnet just clears them
Last edited by Brettski mk2; 11-09-2011 at 08:11 AM.
#274
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
Got told to day that you can get the shocks shortened? anyone had it done. The shocks are irish tarmac so long but stiff.If I use them at my required ride hight I have bugger all travel
Have we got any set up exsperts on here then??
Have we got any set up exsperts on here then??
#277
aka Turbosailorboy
iTrader: (5)
Hi Brett, these are the top mounts You dont want to ask how much they are
As for choice of suspension.......well the current Koni/Ahmed combi are going to have to go in favour of something like B.A.D or similar. Depends if i go to billet uprights on the front as well
Don't make them too big or you will need AG Focus style holes in the bonnet
#278
Too many posts.. I need a life!!
Thread Starter
iTrader: (3)
Join Date: Nov 2009
Location: suffolk
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
Hi Brett, these are the top mounts You dont want to ask how much they are
As for choice of suspension.......well the current Koni/Ahmed combi are going to have to go in favour of something like B.A.D or similar. Depends if i go to billet uprights on the front as well
Don't make them too big or you will need AG Focus style holes in the bonnet
As for choice of suspension.......well the current Koni/Ahmed combi are going to have to go in favour of something like B.A.D or similar. Depends if i go to billet uprights on the front as well
Don't make them too big or you will need AG Focus style holes in the bonnet
Pm me the price??
#279
aka Turbosailorboy
iTrader: (5)