My Texaco 3door Cosworth
30-06-2009, 11:35 PM
#45
Compensation Specialist
Thread Starter
iTrader: (1)
Join Date: Feb 2009
Location: Bury St Edmunds
Posts: 1,149
Likes: 0
Received 0 Likes
on
0 Posts
ok had a fair bit of work done.
Texaco graphics came off and Nathan @ I-Tuned who does all fabrication work and is a work of art knocks spots of Haywood and Scott and at a better price.
hes starting to put a bit of livery on my car and hes finished my twin exhaust system which is 4" all the way through. so anyone want custom work done give him a bell say stuart sent you. you wont be dissapointed
Texaco graphics came off and Nathan @ I-Tuned who does all fabrication work and is a work of art knocks spots of Haywood and Scott and at a better price.
hes starting to put a bit of livery on my car and hes finished my twin exhaust system which is 4" all the way through. so anyone want custom work done give him a bell say stuart sent you. you wont be dissapointed
01-07-2009, 12:07 AM
#47
Compensation Specialist
Thread Starter
iTrader: (1)
Join Date: Feb 2009
Location: Bury St Edmunds
Posts: 1,149
Likes: 0
Received 0 Likes
on
0 Posts
dont know yet mate will be doing the starting map end of week, hopefully ok but we have another long box on standby just in case which can go down centre
01-07-2009, 12:25 AM
#51
no unfortunately, it has a 4 inch down pipe which splits into 2x 2 1/2" that go round each side of the gearbox
then come to meet at a massive split box in the centre of the car, then they both turn around the coner and face out with a big box each side before they exit under the side skirt
then come to meet at a massive split box in the centre of the car, then they both turn around the coner and face out with a big box each side before they exit under the side skirt
01-07-2009, 12:50 PM
#53
10K+ Poster!!
Very impressive exhaust, iirc the BTCC cars had a recessed floor where the side exit sat so it tucked up nicely although to be fair they don't sit that bad on yours as it is.
Good work from that company though, very tidy
Good work from that company though, very tidy
01-07-2009, 06:29 PM
#63
Compensation Specialist
Thread Starter
iTrader: (1)
Join Date: Feb 2009
Location: Bury St Edmunds
Posts: 1,149
Likes: 0
Received 0 Likes
on
0 Posts
no cutting needed at all thats the good thing it has quik release vbands in 3 places for ease of taking it off.
the end pipe goes under kit.
not too sure on the old exhaust yet mate will give you first refusal when i decide to most likely be weekend
the end pipe goes under kit.
not too sure on the old exhaust yet mate will give you first refusal when i decide to most likely be weekend
,awesome car stu,and love that exhaust .quality workmanship
06-10-2009, 09:01 PM
#77
Long awaited Update
Got it started today after fitting new custome fuel setup etc etc.
it fired straight up on base map which was setup for a completely wrong setup.
and suprisingly the exhaust is really quiet and really suprise. Tabetha and I need to have a play about with Map to get the running well enough to run it in. also need to setup the electrics to the stack dash.
will get pics up asap!
Got it started today after fitting new custome fuel setup etc etc.
it fired straight up on base map which was setup for a completely wrong setup.
and suprisingly the exhaust is really quiet and really suprise. Tabetha and I need to have a play about with Map to get the running well enough to run it in. also need to setup the electrics to the stack dash.
will get pics up asap!
