ZAKSPEED ESCORT 4x4 500+HP (328mm rear discs machined rear spoiler profiles here )
#1962
Your a non-commissioned officer in the royal navy, leadership trained, a leader of men, a Submariner etc etc and you cant even control one man and his grinder.
#1965
Thread Starter
PassionFord Post Whore!!
iTrader: (1)
Joined: Jun 2008
Posts: 6,302
Likes: 3
From: Sunny Devon
you making it in carbon?? yourself? vacuum resin infusion or wet lay?
it could have been worse, you could have come back to a pile of body panels that was once a car and a bin full of used grinder discs
Your a non-commissioned officer in the royal navy, leadership trained, a leader of men, a Submariner etc etc and you cant even control one man and his grinder.
it could have been worse, you could have come back to a pile of body panels that was once a car and a bin full of used grinder discs
Your a non-commissioned officer in the royal navy, leadership trained, a leader of men, a Submariner etc etc and you cant even control one man and his grinder.
as for the other two comments absolute class
#1971
Thread Starter
PassionFord Post Whore!!
iTrader: (1)
Joined: Jun 2008
Posts: 6,302
Likes: 3
From: Sunny Devon
been busy to night nearly got the floor finished
i have also cut some more holes in the inner sills which will be flared too.
just got to make new kick panels to finish it all off .
i have also cut some more holes in the inner sills which will be flared too.
just got to make new kick panels to finish it all off .
Last edited by andy escos; 15-02-2011 at 08:21 PM.
#1977
Thread Starter
PassionFord Post Whore!!
iTrader: (1)
Joined: Jun 2008
Posts: 6,302
Likes: 3
From: Sunny Devon
Yes not much left until i can seal up underneath and get some stone guard on then its ready for primer,i still got to make some chassis mount engine mounts and fit my pedal box before i can paint it with top coat though.
#1979
Thread Starter
PassionFord Post Whore!!
iTrader: (1)
Joined: Jun 2008
Posts: 6,302
Likes: 3
From: Sunny Devon
if i have worked it out right then i have enough room down the side of the gear box on the n/s to get a good size silencer & the prop is high enough in the tunnel i should be able to run the exhaust pipe under the prop with out it being below the floor
#1993
Thread Starter
PassionFord Post Whore!!
iTrader: (1)
Joined: Jun 2008
Posts: 6,302
Likes: 3
From: Sunny Devon
done a bit more to night cut out the hand brake mount hole out
then i rolled the car over so i can fully weld all the new floor & tunnel also got to make a new gear box x member 7 mount the centre prop support .
richie dared me to do an up date so here it is lol
and for those who keep asking about the body kit here is a quick peek
then i rolled the car over so i can fully weld all the new floor & tunnel also got to make a new gear box x member 7 mount the centre prop support .
richie dared me to do an up date so here it is lol
and for those who keep asking about the body kit here is a quick peek
#1998
Thread Starter
PassionFord Post Whore!!
iTrader: (1)
Joined: Jun 2008
Posts: 6,302
Likes: 3
From: Sunny Devon
thats the idea ian i got to trim the floor back but leave tags down both sides so i can put rivnuts in & bolt a closing panel on making it totally flat tying into the front spoiler/sump guard ,then leading into the rear diffuser.it will also have a lip going down the running boards so i can fix a rubber strip hope fully giving some sort of ground effect .