sounds good mate can you still remember how to get here ,hope your back gets better soon

 

slight change of plans i was going to run with no interior heater to keep the clean looks of the engine bay but i have now decided to put it in any how so out with the grinder again & cut a bit out again

 

dude seriously lol!!!

your fab work lookd great!!! leave it alone!!!

 

cheers tev it did look good but not very practical though but it will look good again though, as i will make a cover to hide the heater motor like my old one .

 

fair play dude with all the effort you have put in best to do it right,

 

Could you not have just worn a jacket?

 

yeah just a couple of treatments at a chiropractor and i shall be fighting fit again lol.

pm your address and i'll google it and shall find it no prob's mate.
cheeRS

 

thanks china

it would of been easier but i like a challenge,apart from that i just love cutting steel out

 

you have pm mate.

 

 

Haha yeah there is some thing addictive about the way the 1mm discs cut.

 

cutting with a stihle saw,a addictive deffo when its a saff

 

Andy you just love cutting but your right to do it mate

 

your right there mate if it means i got to cut certain stuff out so it is better then i will do it fortunately i think that is it

 

received and understood.
God bless google earth lol. See u sunday.

 

see the grinders been out while i been away andy ,still it is becoming better in the long run

 

new heater recess in & welded up






heater out of the way of engine now




and here is one of my new inner roof plates ready to go back in

 

looking superb mate.

dont drink to much guiness or it'll all be wonky lol

 

Very nice mate nice work as all ways

 

Good work as always Andy

 

thanks ronnie i do some of my best work with a beer in me lol

thanks ian
cheers marc

 

Great work there as always Andy and beer too

I like the look of the pressed holes, what did you use for that? I remeber when you cut them out you said you needd to get the press part to finish them.

 

thanks dan
here is the link for the cutter & the flare tool
http://www.frost.co.uk/images/produc...large/9120.jpg
http://www.frost.co.uk/

in the search pane type in flare.

 

tomorrow i will be spot welding the inner roof frame work back in & i might start putting some filler in the inner flitch

 

Thanks Andy

 

looks sweet that andy

 

only to glad to help if i can dan

thanks graham

 

arh looks like its turned a corner and being put back together now, no more grinding? lol

heater matrix area look ace mate

 

thanks mate i think all the grinding is done now so it should be progressing forward from now on in .

 

Bloody hell have you not finished this yet lol.Top work mate.

 

like i keep on saying lol


cant rush perfection can you andy !!




looking good mate

 

Your telling me!!!

 

no not yet glenny there is no point rushing it because i would only rip it apart next year to do it again even better

your right there mate it takes as long as it takes to get it looking right

all right then dougie yours should be like a new shiny penny when you get yours back mate . one day lol

 

Spot on work on the motor as usual mate, really looking forward to getting something done on mine in the near future.
Got my garage home now and hopefully get the base laid for it in a couple of weeks then it's full steam ahead on the P100.

 

thanks mate ,did you get one of those flat pack garages

 

i finally started to put some filler on to smooth out every thing before paint



smoothing the top mounts idea i pinched off gav diamond

 

Looking Good Andy

 

thanks dave

 

Wooohooo construction rather than destruction.

Getting there mate. Will be good to see it finally going back together.

Might even use it next year

 

looks good andy!!! really glad to see some filer going on!!