E5 MDS 4x4 saph re-build . . . for sale . . .
#526
10K+ Poster!!
iTrader: (1)
Join Date: May 2003
Location: Lancashire
Posts: 12,748
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by NEEDFORSPEED
Originally Posted by philram
just read all 14 pages... your doing some great work mate
yes home made my bro did it for me. nice welding eh!
#534
PassionFord Post Troll
Thread Starter
shaped (bent! lol) the dipstick tube to clear the breather and made a fresh bracket painted everythin and bolted to the hose clip sounds dodgy but will be fine
#535
PassionFord Post Troll
Thread Starter
bought an adapter for my oil pressure sender to put inline of the oil feed line for turbo as it wont fit streight into the block cos of the breather but had to use adapters and i forgot about the oil pressure switch for light. and looked so messy so decided to make one to fit both and to look much better. may polish it.
just need to tap the ends and the correct thread for the switch, cant find them anywhere!
just need to tap the ends and the correct thread for the switch, cant find them anywhere!
#537
PassionFord Post Troll
Thread Starter
while i was at my brothers this wkend the engineer next door was nice enough to tap the fitting then i polished it and finished it off. hoses all made up fits spot on just going to make a nice little bracket to hold it. polished the pressure senser aswel
its the little bits that take the time!
its the little bits that take the time!
#538
PassionFord Post Troll
Thread Starter
got a load done today.
sump arrived from mike r, whoever mike uses charged Ł40 to sand blast it and an extra Ł50 to drill some holes and weld the threaded bosses on! didnt think it would of cost that much would of got it done myself lol.not his fault anyway very good service from him.
got everything painted & built up on trolley
note the freshly painted floor and walls ready for the build up lol even got a heater and 'art work' on the wall
started makeing the hoses for the breather aswel if you can see. bit of a twat cutting it as the angle grinders at work so i used a hack saw!
box and diff, everything on etc just waiting for an exchange rack then i cant go any further with it really until my manifold turns up, promised this week
got a new spigot bearing to go in
sump arrived from mike r, whoever mike uses charged Ł40 to sand blast it and an extra Ł50 to drill some holes and weld the threaded bosses on! didnt think it would of cost that much would of got it done myself lol.not his fault anyway very good service from him.
got everything painted & built up on trolley
note the freshly painted floor and walls ready for the build up lol even got a heater and 'art work' on the wall
started makeing the hoses for the breather aswel if you can see. bit of a twat cutting it as the angle grinders at work so i used a hack saw!
box and diff, everything on etc just waiting for an exchange rack then i cant go any further with it really until my manifold turns up, promised this week
got a new spigot bearing to go in
#549
PassionFord Post Troll
Thread Starter
Originally Posted by Matt Baxter
awesome work
when do you want it finished by?
when do you want it finished by?
#552
PassionFord Post Troll
Thread Starter
well got the twat of a clutch sorted! when i put the box on it was only for picture purpose
it was sat 10mm off the box (another miss measure) lol so i had to further modify the slave cylinder base. some pics standard part welded up and 3 holes tapped for the tilton slave and the end cut off
turned the middle shim up a further 10mm and that was enough. fitted new o rings in the slave at the same time so i know it will be fine
it was sat 10mm off the box (another miss measure) lol so i had to further modify the slave cylinder base. some pics standard part welded up and 3 holes tapped for the tilton slave and the end cut off
turned the middle shim up a further 10mm and that was enough. fitted new o rings in the slave at the same time so i know it will be fine
#555
Wahay!! I've lost my Virginity!!
Join Date: Mar 2007
Location: GLOUCESTER
Posts: 68
Likes: 0
Received 0 Likes
on
0 Posts
Engine looks amazing mark Done a lot of work on the shell, wont be long now but its so f*****g cold everything takes longer Has your manifold turned up yet?
#556
OMG mark cars gonna be amazing you better take me for a spin in it!!!!!, well done mate you done a great job with that engine just makes me miss mine even more! , but for now no more toys for me i got to make my baby son priority. I wanna try call in see you all works a nightmare they got me doin 2-12 saw gilby other day but was only quick i never asked how he was doin with m old saph? anyway i will have to call by to see for my self i guess! anyway keep up the good work
#557
PassionFord Post Troll
Thread Starter
at last the manifolds arrived from norway. just need to cut the flange off for external wastegate and bolt the tial one on and weld a bung in for egt sensor then take it with front pipe to get ceramic coated. gives you so much more room from the head than 2wd manifold or even 4x4 so im happy. placed a t35 on just for picture purposes!!
and one of the minker roll bar/compression strut setup. just need to get new rose joints for them
and one of the minker roll bar/compression strut setup. just need to get new rose joints for them