PassionFord - Ford Focus, Escort & RS Forum Discussion

Notices
General Car Related Discussion. To discuss anything that is related to cars and automotive technology that doesnt naturally fit into another forum catagory.

Pf01 vs Pf09

Thread Tools
 
Search this Thread
 
Old 06-12-2018, 08:54 PM
  #1  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default Pf01 vs Pf09
Any differences to each other ? Only my mapper has told me to get a PF09 as my PF01 doesn't show closed throttle ?

this was the message i got ...

The pf01 has a switch which shows open circuit with closed throttle so that's not going to work unfortunately. The pf09 is the one we need. Ie any other 0 to 5v sensor.


I'm sending him a PF09 so he can carry on ..on Saturday when he's back from Scotland.
Rsmat is offline  
Reply Like
Old 06-12-2018, 09:41 PM
  #2  
Adam-M
PassionFord Post Troll
 
Adam-M's Avatar
 
Join Date: Feb 2014
Location: Scotland
Posts: 3,120
Received 315 Likes on 288 Posts
Default
Yeah mate they are 0-5v but they work opposite to each other, one will be 5v at idle going down to 0v the other starts at zero.

i take it the simtek can’t work with a pf01?
Last edited by Adam-M; 06-12-2018 at 09:42 PM.
Adam-M is offline  
Reply Like
Old 06-12-2018, 09:45 PM
  #3  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default
Originally Posted by Adam-M
Yeah mate they are 0-5v but they work opposite to each other, one will be 5v at idle going down to 0v the other starts at zero.

i take it the simtek can’t work with a pf01?

ah got ya mate that's why then ..and yea it's the simtek I've had fitted ..won't work with the PF01 then
Rsmat is offline  
Reply Like
Old 06-12-2018, 09:47 PM
  #4  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default
So swapping the outer wires round like when you got L8 on a l6 loom not work mate ?
Rsmat is offline  
Reply Like
Old 06-12-2018, 10:01 PM
  #5  
Adam-M
PassionFord Post Troll
 
Adam-M's Avatar
 
Join Date: Feb 2014
Location: Scotland
Posts: 3,120
Received 315 Likes on 288 Posts
Default
I’m pretty sure spwapping the wires only enables you to run a pf09 on a 2wd loom and vise versa. If your stuck I could dig out my pf09 and meet your mapper up here so he’s got it.
Adam-M is offline  
Reply Like
The following users liked this post:
Rsmat (06-12-2018)
Old 06-12-2018, 10:08 PM
  #6  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default
Ah got ya ..so it's deffo the pf09 I need then ..I'm pretty sure he's mapping a car at Andy Gallaghers mate ..mega thanks for the offer but I've just posted one out for him to area 52 ..top man Adam really appreciate it mate
Last edited by Rsmat; 06-12-2018 at 10:12 PM.
Rsmat is offline  
Reply Like
Old 06-12-2018, 10:13 PM
  #7  
Adam-M
PassionFord Post Troll
 
Adam-M's Avatar
 
Join Date: Feb 2014
Location: Scotland
Posts: 3,120
Received 315 Likes on 288 Posts
Default
I can imagine it being frustrating being held back by something like that, yeah I know he does Andrews mapping and he more that likely passes through my town on the way to AG.

Hope you get get it sorted bud
Adam-M is offline  
Reply Like

Trending Topics

Old 06-12-2018, 10:13 PM
  #8  
markk
10K+ Poster!!
iTrader: (2)
 
markk's Avatar
 
Join Date: May 2003
Location: Lancs
Posts: 10,638
Received 104 Likes on 96 Posts
Default
Its because the PF01 goes open circuit at idle. Useless to any ecu other than Weber setup.
markk is offline  
Reply Like
The following users liked this post:
Rsmat (06-12-2018)
Old 06-12-2018, 10:55 PM
  #9  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default
Originally Posted by markk
Its because the PF01 goes open circuit at idle. Useless to any ecu other than Weber setup.

cheers Mark that makes sense mate
Rsmat is offline  
Reply Like
Old 06-12-2018, 10:57 PM
  #10  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default
Originally Posted by Adam-M
I can imagine it being frustrating being held back by something like that, yeah I know he does Andrews mapping and he more that likely passes through my town on the way to AG.

Hope you get get it sorted bud

Yea it's cool mate ..Steve let me know and I'm in no rush for car as I'm flat out at work so works in my favour tbh ..I'm going DWB after Xmas etc so it will be redundant then the TPS
Rsmat is offline  
Reply Like
Old 07-12-2018, 06:19 AM
  #11  
Caddyshack
10K+ Poster!!

 
Caddyshack's Avatar
 
Join Date: Mar 2013
Location: Guildford
Posts: 10,841
Received 1,031 Likes on 944 Posts
Default
I think I have one you can borrow


Just seen above that you have one and an offer but mine is here if you need them
Last edited by Caddyshack; 07-12-2018 at 08:11 AM.
Caddyshack is offline  
Reply Like
Old 07-12-2018, 08:16 AM
  #12  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default
Originally Posted by Caddyshack
I think I have one you can borrow


Just seen above that you have one and an offer but mine is here if you need them

thanks Toby mate ..top offer .hopefully the one I have sent works ..I'm.sticking the DBW TB on after Xmas ..I think the old cosworth stuff is a pain now a days
Rsmat is offline  
Reply Like
Old 07-12-2018, 02:05 PM
  #13  
Adam-M
PassionFord Post Troll
 
Adam-M's Avatar
 
Join Date: Feb 2014
Location: Scotland
Posts: 3,120
Received 315 Likes on 288 Posts
Default
DBW does seem the way forward that’s what I’m going mate
Adam-M is offline  
Reply Like
The following users liked this post:
Rsmat (07-12-2018)
Old 07-12-2018, 02:09 PM
  #14  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default
Originally Posted by Adam-M
DBW does seem the way forward that’s what I’m going mate

yea I've got all the bits .. would have fitted before mapping but I didn't want to take the inlet off to have altered to fit DBW this side of Xmas .
Rsmat is offline  
Reply Like
Old 07-12-2018, 03:02 PM
  #15  
Caddyshack
10K+ Poster!!

 
Caddyshack's Avatar
 
Join Date: Mar 2013
Location: Guildford
Posts: 10,841
Received 1,031 Likes on 944 Posts
Default
I want individual throttles on mine but to go dbw I either need to find that driver for my vipec or swap to emtron and I don’t fancy another about turn and buy again.
Caddyshack is offline  
Reply Like
Old 07-12-2018, 03:23 PM
  #16  
Adam-M
PassionFord Post Troll
 
Adam-M's Avatar
 
Join Date: Feb 2014
Location: Scotland
Posts: 3,120
Received 315 Likes on 288 Posts
Default
Originally Posted by Rsmat
yea I've got all the bits .. would have fitted before mapping but I didn't want to take the inlet off to have altered to fit DBW this side of Xmas .

what thorttle body and pedal did you go for?
Adam-M is offline  
Reply Like
Old 07-12-2018, 05:17 PM
  #17  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default
Mk7 fiesta pedal and Audi A4 TB mate
Rsmat is offline  
Reply Like
Old 07-12-2018, 05:21 PM
  #18  
Adam-M
PassionFord Post Troll
 
Adam-M's Avatar
 
Join Date: Feb 2014
Location: Scotland
Posts: 3,120
Received 315 Likes on 288 Posts
Default
Originally Posted by Rsmat
Mk7 fiesta pedal and Audi A4 TB mate
Is that throttle body the same bolt pattern as a cossie one?
Adam-M is offline  
Reply Like
Old 07-12-2018, 09:03 PM
  #19  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default
Yea according to Andy it is mate ..have you seen the vid he's put on FB today with the simtek set up on a board working the TB and everything ?
Rsmat is offline  
Reply Like
Old 07-12-2018, 09:14 PM
  #20  
Adam-M
PassionFord Post Troll
 
Adam-M's Avatar
 
Join Date: Feb 2014
Location: Scotland
Posts: 3,120
Received 315 Likes on 288 Posts
Default
Originally Posted by Rsmat
Yea according to Andy it is mate ..have you seen the vid he's put on FB today with the simtek set up on a board working the TB and everything ?
Good stuff mate I’ve got the one off a 1.8 20vt which is a direct fit (MarkK’s recommendation) I’m assuming yours will be the same part

Did see the video it’s an impressive package especially for the money
Adam-M is offline  
Reply Like
The following users liked this post:
Rsmat (07-12-2018)
Old 07-12-2018, 09:59 PM
  #21  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default
Originally Posted by Adam-M


Good stuff mate I’ve got the one off a 1.8 20vt which is a direct fit (MarkK’s recommendation) I’m assuming yours will be the same part

Did see the video it’s an impressive package especially for the money

yea that's the one mate bolts straight up same as A4 TB then ..Yea lot of spec for the money the simtek is.
Rsmat is offline  
Reply Like
Old 15-12-2018, 01:01 PM
  #22  
Rick
15K+ Super Poster!!

 
Rick's Avatar
 
Join Date: May 2003
Location: Stockport, Cheshire
Posts: 15,885
Received 17 Likes on 17 Posts
Default
Don't use either, the are both ancient, The advantage of standalone is you can use modern cheap sensors.
Rick is offline  
Reply Like
The following users liked this post:
Rsmat (16-12-2018)
Old 23-12-2018, 02:08 PM
  #23  
Rsmat
300+

Thread Starter
iTrader: (2)
 
Rsmat's Avatar
 
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes on 516 Posts
Default
Originally Posted by Rick
Don't use either, the are both ancient, The advantage of standalone is you can use modern cheap sensors.

used a PF09 for now ..working perfect ..switching to DBW in 2019
Rsmat is offline  
Reply Like
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Pf09 / pf01
timsrs
Ford Sierra/Sapphire/RS500 Cosworth
8
08-05-2016 06:43 PM
Is a RED PF09 TPS the same as a BLACK PF09?
boXXer
Technical help Q & A
3
16-04-2011 03:13 PM
Pf01 and Pf09 Throttle Position Sensors
JokerDisco
Technical help Q & A
5
18-08-2009 10:30 AM
Which is Better PF01 or PF09 TPS?
Ryan
General Car Related Discussion.
1
30-12-2006 12:18 PM
Best place to buy a TPS PF01 quick & cheap???
Disabled Account
General Car Related Discussion.
2
24-01-2005 06:08 PM
Back to Subforum
General Car Related Discussion.
View Next Unread
Escort cabriolet MK4 slow wipers and slow electric windiws




Advanced Search
Quick Reply: Pf01 vs Pf09


Reply Closed Thread Share
Forum Jump

All times are GMT. The time now is 06:18 PM.