what bhp and torque figures for a t4??? (now results & graph)
#43
like iv said mate not trying to piss on your fireworks or put your car down but it isnt 448 bhp yet..and if it was you would piss past your mate and fuckoff up the road..going by where its at at the mo it will do about 470 al mapped at 32 psi
#44
how can a rolling road give you power readings from flywheel and wheels with calculating it?
i have to phone back tomorrow and speak to the guy who did it for him to explain.
#45
the guy on the phone at motorscope where my car was doen has just told me both power's are correct to 1bhp so it must be my gearbox or diff,
how can a rolling road give you power readings from flywheel and wheels with calculating it?
i have to phone back tomorrow and speak to the guy who did it for him to explain.
how can a rolling road give you power readings from flywheel and wheels with calculating it?
i have to phone back tomorrow and speak to the guy who did it for him to explain.
#47
10K+ Poster!!
iTrader: (21)
Something is quite clearly a miss there mate, go elsewhere
To be honest, if MSD has told you it is 450bhp and it's all ok, I would believe them!!
Done the same when Karl set ours up, he said "It is 350bhp and 350ft/lb torque, plus or minus 5 each way, on both"
As above if he's telling you it is your gearbox or diff, you're getting fobbed off
To be honest, if MSD has told you it is 450bhp and it's all ok, I would believe them!!
Done the same when Karl set ours up, he said "It is 350bhp and 350ft/lb torque, plus or minus 5 each way, on both"
As above if he's telling you it is your gearbox or diff, you're getting fobbed off
#48
Cake lover!
iTrader: (3)
My car made 385bhp at the wheels and 455bhp at the fly, this works out at roughly 18% for transmisson losses. Your car at 342bhp works out at about 404bhp with the same losses. Mine was done on a dyno dynamics hub dyno.
I have never been confident in dastek rollers since i went to a RR day a few years back and all the cars were making well over what they did else where.
Also your torque is way down on what mine is, but like you said the mapping isnt finished yet so there may be more to come. Aslong as you enjoy it thats all that matters.
I have never been confident in dastek rollers since i went to a RR day a few years back and all the cars were making well over what they did else where.
Also your torque is way down on what mine is, but like you said the mapping isnt finished yet so there may be more to come. Aslong as you enjoy it thats all that matters.
#52
10K+ Poster!!
iTrader: (4)
My car made 385bhp at the wheels and 455bhp at the fly, this works out at roughly 18% for transmisson losses. Your car at 342bhp works out at about 404bhp with the same losses. Mine was done on a dyno dynamics hub dyno.
I have never been confident in dastek rollers since i went to a RR day a few years back and all the cars were making well over what they did else where.
Also your torque is way down on what mine is, but like you said the mapping isnt finished yet so there may be more to come. Aslong as you enjoy it thats all that matters.
I have never been confident in dastek rollers since i went to a RR day a few years back and all the cars were making well over what they did else where.
Also your torque is way down on what mine is, but like you said the mapping isnt finished yet so there may be more to come. Aslong as you enjoy it thats all that matters.
dastek are good with a good operator. my skyline came in at 14 % losses in rwd mode same as my cos trans losses 2wd.
#54
yeah but thats wrong...you wont get a rwd in the land that only looses 14%your skyline would have more losses than a cossie due to having transfer box etc...
#56
thats exactly what iv read and learnt with our rollers..think the 4wd cossies normaly come out between 20-22% though but evos and skylines are around 24%..cheers danny
#57
saff is working!!!...atm
iTrader: (1)
Join Date: May 2006
Location: fishburn sex shop...co.durham
Posts: 8,984
Likes: 0
Received 0 Likes
on
0 Posts
but u forgot to say the percentage lost goes down the more power u have.......after all it's the same parts that lose the power on a 200bhp car and a 400bhp car for example........
#58
#60
well if thats true b13 jus should have less losses not more,hes works out ove 22%..they say once youve got more power moving the same parts you may experience less losses but its so small it never realy shows..danny
#64
10K+ Poster!!
iTrader: (4)
try this........ http://www.pumaracing.co.uk/POWER3.htm read the "true loss" bit
thats a good read and validates my thoughts of 14 % losses as he quotes 12 - 14 % on a 300 - 500 bhp car.
trans losses are always over exagerated and it seems logical to me that the % will decrease as the power increases.
if a 1000 bhp skyline lost 22 % at all 4 wheels it would have 780 bhp at the wheels now surely anyone with a ounce of sense realises that is just bullshit.
#65
10K+ Poster!!
iTrader: (4)
skyline has 60 more bhp, skyine at equal power would have higher % loss so skyline does have higher % losses at any given power.
as for nothing at 14 % ever are you trying to tell me a 2000 bhp rwd car only has 1720 bhp at the wheels ?
or an 8000 bhp dragster would loose 1120 bhp ........ errrr no
Last edited by scoooby slayer; 14-09-2009 at 08:15 PM.
#66
skyline has 60 more bhp, skyine at equal power would have higher % loss so skyline does have higher % losses at any given power.
as for nothing at 14 % ever are you trying to tell me a 2000 bhp rwd car only has 1720 bhp at the wheels ?
il eat my own finger if it would loose 280 bhp !
as for nothing at 14 % ever are you trying to tell me a 2000 bhp rwd car only has 1720 bhp at the wheels ?
il eat my own finger if it would loose 280 bhp !
#67
10K+ Poster!!
iTrader: (4)
how do you explain b13 jus car loosing so much thro trans on same rollers as yours???a skyline box will have bigger losses than a cossy box fact yet the rollers gave the same losses???i take it you have low ratios too??on your dyno plot it says you only get 13.?mph to every k in 4th..so your car only does 100 mph at 7.5k in 4th??them rollers are wrong,maybe not the wheel fig but transmission is wrong!!iv had cossies from std to 600bhp and even at 600 bhp they still loose 16-17%so yes that 2000 bhp car will be 1720 bhp after losses cos the box he uses will be bigger and stronger..like your liner box is bigger and stronger than a t5...
never noticed the speed before must of not been calibrated to machine for speed. i have a previous run in the skyline with different turbos in 4wd and that still only had 18.6 % losses, still with dastek but no speed per rpm even indicated, i think rob must not bother with the speed bit.
tweenie rob has been mapping and r/r skylines for years so im confident the figures are as close as they can be on a r/r. tweenies a legend.
as for b13 jus result his wheel figure must be pretty close but fly massivly over exagerated for some reason ?
at the end of the day wheel figures are all that really matter as the power we actually get to the road.
Thread
Thread Starter
Forum
Replies
Last Post
nicodinho
Ford Non RS / XR / ST parts for sale.
6
07-10-2015 12:56 PM
DavidK
Ford Sierra/Sapphire/RS500 Cosworth
1
27-09-2015 02:55 PM