180Mph / 500Hp Capri - Dyno plot + video.
#1
180Mph / 500Hp Capri - Dyno plot + video.
After disapointment last night with the thread vanishing, here are the details of the 180mph Capri.. (in the wet I may add)
HUGE CONGRATULATIONS to Nik, Mark, Jim, Keith and all involved in the build.
503.6 BHP @ Flywheel
485 Ft/LB @ Flywheel
430.6 BHP @ The Wheels
414 FT/LB @ The Wheels
http://www.youtube.com/watch?v=x3ZFexeqEaQ
HUGE CONGRATULATIONS to Nik, Mark, Jim, Keith and all involved in the build.
503.6 BHP @ Flywheel
485 Ft/LB @ Flywheel
430.6 BHP @ The Wheels
414 FT/LB @ The Wheels
http://www.youtube.com/watch?v=x3ZFexeqEaQ
Last edited by Luca; 23-09-2008 at 07:54 PM.
#6
I've found that life I needed.. It's HERE!!
Join Date: Oct 2007
Location: Straight outta Essex
Posts: 1,081
Likes: 0
Received 0 Likes
on
0 Posts
Fuckin hell!! 180mph!! My capri 2.8 is as unstable as fuck at about 115-120!
Congratulations, give the man with the granite potatoes a big cigar!!
Congratulations, give the man with the granite potatoes a big cigar!!
Trending Topics
#12
I've found that life I needed.. It's HERE!!
luke have you seen much of tonys big block v8 capri i saw it once think it made around 400hp under 4000rpm on the jkm rollers not seen it for while so sure it should be making over 1000hp by now
#13
10K+ Poster!!
Colin its very difficult to compare AVA wheels figs to DD ones.
from what I can gather any car that has been ran on AVA will see a lower wheel fig to a DD but will probably get a fly fig higher than you might expect.
from what I can gather any car that has been ran on AVA will see a lower wheel fig to a DD but will probably get a fly fig higher than you might expect.
#16
1st to 200 without NOS
iTrader: (2)
After disapointment last night with the thread vanishing, here are the details of the 180mph Capri.. (in the wet I may add)
503.6 BHP @ Flywheel
485 Ft/LB @ Flywheel
430.6 BHP @ The Wheels
414 FT/LB @ The Wheels
http://www.youtube.com/watch?v=x3ZFexeqEaQ
503.6 BHP @ Flywheel
485 Ft/LB @ Flywheel
430.6 BHP @ The Wheels
414 FT/LB @ The Wheels
http://www.youtube.com/watch?v=x3ZFexeqEaQ
Doesn't the car sit at funny angle on those rollers though.
#25
Thanks for the nice comments guys
I'm still buzzing from the experience even now
As well as Mark Shead's great engine build and mappingI would also like to acknowledge the great work done to the car by JKM Performance in Portsmouth who handled virtually the entire build.Thanks Jim (and Keith) you did me proud!!
ps.The above credit is not an advert,after all we've been through with the Capri they never want to see another old Ford ever again!!!!!!
Nick
I'm still buzzing from the experience even now
As well as Mark Shead's great engine build and mappingI would also like to acknowledge the great work done to the car by JKM Performance in Portsmouth who handled virtually the entire build.Thanks Jim (and Keith) you did me proud!!
ps.The above credit is not an advert,after all we've been through with the Capri they never want to see another old Ford ever again!!!!!!
Nick
#26
Passionford Thread Killer
iTrader: (8)
Thanks for the nice comments guys
I'm still buzzing from the experience even now
As well as Mark Shead's great engine build and mappingI would also like to acknowledge the great work done to the car by JKM Performance in Portsmouth who handled virtually the entire build.Thanks Jim (and Keith) you did me proud!!
ps.The above credit is not an advert,after all we've been through with the Capri they never want to see another old Ford ever again!!!!!!
Nick
I'm still buzzing from the experience even now
As well as Mark Shead's great engine build and mappingI would also like to acknowledge the great work done to the car by JKM Performance in Portsmouth who handled virtually the entire build.Thanks Jim (and Keith) you did me proud!!
ps.The above credit is not an advert,after all we've been through with the Capri they never want to see another old Ford ever again!!!!!!
Nick
What axle setup are you running? Im doing a yb capri atm and have an atlas with quaife lsd and shafts (t34, grey ect.) and I dont know if its man enough for the job?
p.s well done, very nice.
#27
Correct Rich,GT3076.82
Incidentally the DD rolling road calculated flywheel figure was only 3bhp different to the figure measured on the Norris engine dyno on the same boost.........
Incidentally the DD rolling road calculated flywheel figure was only 3bhp different to the figure measured on the Norris engine dyno on the same boost.........
#31
Loader,your axle should be fine
Mine survived 170 1/4 mile blasts at well over 300bhp and so far so good with the new engine,with just uprated shafts and a tightened up diff
Actually standard shafts were fine until I fitted sticky track day tyres
Mine survived 170 1/4 mile blasts at well over 300bhp and so far so good with the new engine,with just uprated shafts and a tightened up diff
Actually standard shafts were fine until I fitted sticky track day tyres
#32
10K+ Poster!!
iTrader: (4)
After disapointment last night with the thread vanishing, here are the details of the 180mph Capri.. (in the wet I may add)
HUGE CONGRATULATIONS to Nik, Mark, Jim, Keith and all involved in the build.
503.6 BHP @ Flywheel
485 Ft/LB @ Flywheel
430.6 BHP @ The Wheels
414 FT/LB @ The Wheels
http://www.youtube.com/watch?v=x3ZFexeqEaQ
HUGE CONGRATULATIONS to Nik, Mark, Jim, Keith and all involved in the build.
503.6 BHP @ Flywheel
485 Ft/LB @ Flywheel
430.6 BHP @ The Wheels
414 FT/LB @ The Wheels
http://www.youtube.com/watch?v=x3ZFexeqEaQ
so this was done on an engine dyno and r/r and made same power ? so this is genuine proof that in your car you have exactly 17 % trans losses proven buy r/r and engine dyno.
#36
Advanced PassionFord User
Join Date: Jul 2004
Location: hants
Posts: 1,588
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the nice comments guys
I'm still buzzing from the experience even now
As well as Mark Shead's great engine build and mappingI would also like to acknowledge the great work done to the car by JKM Performance in Portsmouth who handled virtually the entire build.Thanks Jim (and Keith) you did me proud!!
ps.The above credit is not an advert,after all we've been through with the Capri they never want to see another old Ford ever again!!!!!!
Nick
I'm still buzzing from the experience even now
As well as Mark Shead's great engine build and mappingI would also like to acknowledge the great work done to the car by JKM Performance in Portsmouth who handled virtually the entire build.Thanks Jim (and Keith) you did me proud!!
ps.The above credit is not an advert,after all we've been through with the Capri they never want to see another old Ford ever again!!!!!!
Nick
well done nick makes all the work worth while
i hear you had a panic on the night before