where have you mounted your..
14-06-2008, 10:10 PM
#3
BANNED
BANNED
Join Date: Nov 2005
Location: stockton
Posts: 3,112
Likes: 0
Received 0 Likes
on
0 Posts
normaly the return to the tank is from bottom but some are from the side do you have any pic's to help people figure it out
Last edited by blacky.; 15-06-2008 at 10:41 AM.
14-06-2008, 10:14 PM
#5
had a good few hours on it last weekend, got the ex manifold on properly now, and got the rollers back from being machined. reassembled them and the complete inlet is now back on.
need to get a few bolts etc before i can refit the boost pipes.
went to pirtek today to see about hose/ittings but they were shut
still got a bit to do mind, need to cut out the metal for the seat mounts and chip has very kindly offered to come round and do some welding, i just need to get the metal etc.
still dont know what to do about the rear beam, turns out i have 4i hubs and the cossy brakes dont fit, and it also has a 4x4 beam/diff/and shafts and i was royally conned by some mug off here...
or am i the mug?
lol
anyway, other than that, i need to sort out the oil/water and brake plumbing, make up the dash for the stack stuff, fit the adj tcas and comp struts, refit the car loom
and then it will be off to promethius for engine/rest of the car wiring.
i still need to get a 3 bar map sensor, gel battery, hydro handbrake, all the fittings for the vac side
and then of course have it mapped and run in...
not much then
need to get a few bolts etc before i can refit the boost pipes.
went to pirtek today to see about hose/ittings but they were shut
still got a bit to do mind, need to cut out the metal for the seat mounts and chip has very kindly offered to come round and do some welding, i just need to get the metal etc.
still dont know what to do about the rear beam, turns out i have 4i hubs and the cossy brakes dont fit, and it also has a 4x4 beam/diff/and shafts and i was royally conned by some mug off here...
or am i the mug?
lol
anyway, other than that, i need to sort out the oil/water and brake plumbing, make up the dash for the stack stuff, fit the adj tcas and comp struts, refit the car loom
and then it will be off to promethius for engine/rest of the car wiring.
i still need to get a 3 bar map sensor, gel battery, hydro handbrake, all the fittings for the vac side
and then of course have it mapped and run in...
not much then
Trending Topics
14-06-2008, 10:21 PM
#8
couple of months i reckon!!
ive been sayin that for ages but i had to spend 5 week in manchester training for the new job and weekends were dedicated to the wife and littleun (well, 2 weekends were trailering the car to pro alloy and hayward and scott lol)
and last weekded was the first time id had a chance to do anything on it and i made some good progress, so kinda getting in the swing of things again
its just a pain in the ass with my driving being quite and uphill slope, as the garage is tiny its a right cunt getting the car in and out to work on
ive been sayin that for ages but i had to spend 5 week in manchester training for the new job and weekends were dedicated to the wife and littleun (well, 2 weekends were trailering the car to pro alloy and hayward and scott lol)
and last weekded was the first time id had a chance to do anything on it and i made some good progress, so kinda getting in the swing of things again
its just a pain in the ass with my driving being quite and uphill slope, as the garage is tiny its a right cunt getting the car in and out to work on
Thread
Thread Starter
Forum
Replies
Last Post
rsguy
General Car Related Discussion.
44
29-09-2015 03:29 PM
DavidK
Ford Sierra/Sapphire/RS500 Cosworth
1
27-09-2015 02:55 PM
Andypandy260
General Car Related Discussion.
1
23-09-2015 10:28 PM