would anyone use EA to map a fresh yb to 400bhp???

 

I wouldn't go to anyone but Karl Norris.

 

I have no experience with EA but my advice is DO NOT settle for second best for the sake of a few hundred miles!

I drove to London from Scotland to have my management system fitted.

 

can of worms

 

Well and truely opened then??!!!!!!!!!!!!

 

i'll put the kettle on...............wheres them hobnobs

 

Should not be a can of worms at all.

All the best tuners have got good cars out there doing the biz.

The ones that havent aint that good, simple as.

 

Based on no personal experience, just entirely on posted threads
( so 100% accuracy is not guaranteed )

But seen quite a few posts by unimpressed customers, many who had work carried out by other employees and not Paul Hills himself.

But every tuner has at least one critic, so try and go with the best rep' even if it means a few extra miles

 

i have used them!!! so have some of my mates.lets just say i wont " I WONT BE GOING THERE AGAIN"

 

why wont you go back again???
Prices??
knowledge??
service??

 

Hence why im going to be making the trip up to Blackpool from Derby to see Stu....see/hear bugger all said against him and MSD but many thumbs up's seen on here, so cant argue with that in an age when people are quite happy to moan when something aint right but seem forgetfull when alls perfect

 

wouldnt take my push bike to EA, never mind a cossie

 

Melted engines?

 

External Wastegates mounted on EGR pipes anyone? .. Oh and my saff ( previously mapped by EA) running 9% C.O on greens? ... In a word, NO!!

MSD By a mile, worth the distance for peace of mind, simple as.

 

ok chaps point taken. will give groove a call in the morning.
thanks for the info

 

DAMN !!!

Just booked my Grifter in there for a puncture repair

 

You want to be careful, they will probably put the tyre valve in wrong, and end up running the tyre at 300Psi, just like someones brand new engine .. Then not pay for the damage and lie about the fitting session, and say that you told them to mount the valve like that, so there

 

What engine would that be Wil?

 

Evenin' Ian, fancy seeing you here ..

Not sure about the engine, think it was only about 10k's worth of nigh-on indestructable spec YB.. (Unless you run 50psi of course.....)

 

52psi actually........enough for that Grifter bike tyre?

 

lets just say im doing another rebuild!!

 

Even for my stylish whitewalls ????

 

I had to do one as well.........funny that, what a coincidence. We must have both been unlucky....

 

Ok.....60 psi it is then sir.......

 

yeh i wasnt best pleased,my mates skyline went bang 2!

 

Take it to joe at GSMOTOSPORT in collier row

 

Yours, mine and a mates skyline engine?....got to be just a coincidence. He couldn't have fucked anyone elses engine surely?

 

He VERY nearly done mine with the state of the map he gave it!

 

I use McCain chips......20 mins 180 degree's in the fan assist......splash of red.....bob on

 

I used MSD TWICE and the chips, they supplied TWICE, did not work TWICE.
I went to get the problem sorted at EA, with 100% success, now it runs perfect.
On a lighter note MSD did give me a full refund without hesitation, but a full mapping sessions was mentioned, even though it didn't need it at this level(stage three).
I can only say when I went, that PAUL, was confident the MSD chip was NOT to blame, until after exhausting all other avenues this was changed, the MASSIVE hole in the power band dissapeared before my eyes, despite all being set up according to the sheet supplied by MSD, I now run a EA chip, but going Emerlad ECU anyway as w/m is a load of crap compared with newer stuff, and on a cost/function basis it certainly is.
tabetha

 

Harvey Gibbs.

 

hi,i've had a complete engine rebuild by them.i've never ever found any problems with them.they are down to earth people iv been getting my car mapped there for the last 18 months with very good results running a paul hills chip and the service iv experienced from paul and his staff have been second to none

 

ea reckon a crack amal valve isnt a problem too. and thats just a small part of a few mates problems

 

oops

 

ive seen your car on other forums mate! looks cool, what happened to it?

 

He tried mapping it!

Cheers, you on XRtwo forum?

 

ive used them. cars ran well since 2005