Plastic Welding
#1
15K+ Super Poster!!
Thread Starter
Join Date: May 2003
Location: Southampton
Posts: 18,589
Likes: 0
Received 0 Likes
on
0 Posts
Plastic Welding
Any tips
Or stuff to use?
Want to do some bodykit repair, i.e screw holes that have pulled through, so i want to fill them and redrill.
Cheers
Ryan
Or stuff to use?
Want to do some bodykit repair, i.e screw holes that have pulled through, so i want to fill them and redrill.
Cheers
Ryan
#3
15K+ Super Poster!!
Thread Starter
Join Date: May 2003
Location: Southampton
Posts: 18,589
Likes: 0
Received 0 Likes
on
0 Posts
its not bumper gareth, its the arches and sideskirts.
bacislly you know where they are pop riveted onto the shell, well where they've been on and off a few time and poorly rivets the holes has been crushed and pulled through (hole is about 5-6mm)
so i want to fill these in and redrill the rivet holes.
bacislly you know where they are pop riveted onto the shell, well where they've been on and off a few time and poorly rivets the holes has been crushed and pulled through (hole is about 5-6mm)
so i want to fill these in and redrill the rivet holes.
#6
PassionFord Post Whore!!
Join Date: May 2003
Location: SE
Posts: 9,226
Likes: 0
Received 0 Likes
on
0 Posts
Have a look at this, I use both these kits, IMO the heat will be better for you in this instance...
http://www.glassaid.co.uk/plastic.html
you will also need some aluminium reinforcing mesh, they should sell it...
Just make up some bollox about starting a SMART repair business and need stock etc... They will believe you as every other SOB is
http://www.glassaid.co.uk/plastic.html
you will also need some aluminium reinforcing mesh, they should sell it...
Just make up some bollox about starting a SMART repair business and need stock etc... They will believe you as every other SOB is
#7
PassionFord Post Whore!!
Join Date: Nov 2004
Location: Middlesbrough
Posts: 7,295
Likes: 0
Received 0 Likes
on
0 Posts
olot of the ford plastics wont weld it just moves away from the heat and burns , so the best thing to use is the plastic fillers and fill the hole then sand it flat i did some of the pop rivet hols on the sills of a 3 door iv just restored useing worth industries flexable plastic adesive resin and it works fine
Trending Topics
#8
PassionFord Post Whore!!
Join Date: May 2003
Location: SE
Posts: 9,226
Likes: 0
Received 0 Likes
on
0 Posts
Dunno if I would just use a flexible filler TBH... Granted some plastics dont like heat, in that instance I would use the cold weld (polyurathane) kit.... Perhaps thats what the Wurth product you mention is?? Does it mix two parts together via a mixer tip, like araldite?
#9
PassionFord Post Whore!!
Join Date: Nov 2004
Location: Middlesbrough
Posts: 7,295
Likes: 0
Received 0 Likes
on
0 Posts
yes mate it is as you say more of a cold weld but its what werth call it iv used it on loads of ford kits and it works fine it dosnt crack out goes of in seconds and is as flexable as the plastic and can be sanded to a nice finish as easy as caty can and best of all you dont have to buy expensive kits just the one tube , iv tried lots of this tipe of material over the years including image plast and dura mix but i find the worth stuff is better
#11
PassionFord Post Troll
Originally Posted by jacko
yes mate it is as you say more of a cold weld but its what werth call it iv used it on loads of ford kits and it works fine it dosnt crack out goes of in seconds and is as flexable as the plastic and can be sanded to a nice finish as easy as caty can and best of all you dont have to buy expensive kits just the one tube , iv tried lots of this tipe of material over the years including image plast and dura mix but i find the worth stuff is better
Anyone know anything about the stuff from www.plastex-uk.com ?
Cheers for any info you can furnish
Thread
Thread Starter
Forum
Replies
Last Post
nicodinho
Ford Non RS / XR / ST parts for sale.
6
07-10-2015 12:56 PM