Anyone know where i can get it done? And how much roughly for rear arms and beam.


Cheap as possible, student dicounted would be nice

 

We get all ours done locally, and as we send so much stuff there it costs buttons

Try your local Yellow Pages

 

speak to gareth T

 

i been quoted 80 pounds to sandblast and powder coat beam and arms and anti roll bar and coil springs

 

BERNARD HASTIE & CO LTD Website 72, Morfa Rd, Swansea, West Glamorgan SA1 2EP Tel: 01792 651541

Surface Systems (Wales) Ltd Unit 8, Lonlas Business Park, Skewen, Neath, West Glamorgan SA10 6SN 01792 818451

Gwent Powder Coatings Ltd 37, Springvale Ind Est, Cwmbran, Gwent NP44 5BD Tel: 01633 860901

Premier Products & Services Unit S, Hirwaun Ind Est, Hirwaun, Aberdare, Mid Glamorgan CF44 9UP
Tel: 01685 810066

Euro Quality Coatings Ltd Wentloog Corporate Park, Wentloog, Cardiff, South Glamorgan CF3 2ER Tel: 029 2036 2999

Almesco Ltd Unit D17, Western Avenue, Bridgend Industrial Estate, Bridgend, Mid Glamorgan CF31 3RT Tel: 01656 679679

Plastic Coatings Ltd Pontymister Industrial Estate, Risca, Newport, Gwent NP11 6NP Tel: 01633 612617

Courtesy of Yell.com

David

 

Be careful using industrial powder coaters, I once got a set of alloys done and they used shot to blast them needless to say they didn't look particularly great with stonechip finish

 

I have been quoted £30 to blast the beam and powder coat it if that gives you any idea of cost.

 

cheers peeps, will fin our.

Spiky can Gareth get it done?

 

So you reckon about £40 to get the lot powder coated?

 

had these done for £40

 

I'm in the process of getting mine ready to be done, but I'm windy about getting the arms done with the spherical bearings in situ. Anyone know if this is OK or not?

I'm too grippy to buy a new set too!

Any ideas on cheap places for newies?

Neil.

 

We get them done without the bearing in, then just run a tap back down the thread. Or sometimes we screw in some old worn out joints. Dont leave yours in that your going to re-use. If you know your size try Martin (MEFmotorsport) in the traders section

 

Didn't know they were threaded in!

I'm thinking I might get the beam and half shafts powder coated, but just have the arms blasted. Then I can paint them by hand with no worries about heat damage.

Neil.

 

cost me 40 quid for rocker cover and inlet manifold,
in blue but its got a purple twist to it,
it looks

 

sorry rhys,, was out with my friend last night and forgot to ask him

 

lol, nps Gareth just ask him when you see him next. Would he be able to sand blast aswell?

 

u have pm rhys

 

whilst we are on the subject of paint... ish.. can i jsut hijack this post for a quick q?

how much do people reckon to get the bumpers sprayed??? not the whole bumper just the small bits taht are faded and greay would rather them body coloured makes the car look tidier... any rough idea would be good

thanks rhys

katie x

ps
hehe rhys do u ask for student rates everywhere u go worth a try!!

 

LOL nps Katie,

Worth asking about student discounts, even if its enough to buy one more pint its worth it

as for bumper i wont have a clue sorry.


Bowk you have PM back mate

 

rhys i can get it done

for beam and arms probably be about £50

will be shot blasted etc before hand

 

Craig, do you mean have to get them shot blast or the same place does it too?

I think i know a guy who can blast the stuff but just trying to get hold of him seems to be a nightmare

 

my bloke does it all

blaster is only in on a monday tho makes turnarround times a little bit longer

hes getting quicker tho

 

Sweet nice one Craig! Ok sounds easier, just trying to get some Spare rear disc gaurds (going to try Fords tomorrow). then once got them i will be ready mate

 

is he



only jokin craiger

 

yes he is ryan

when u next coming up

 

whenever my bits are down, and as soon as i finish nige's loom