need a 2wd saffy bottom end !(found one thanks !!)
#1
15000
Thread Starter
Join Date: Mar 2006
Location: HEYSHAM NR LANCASTER , LANCS
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
![Talking](https://passionford.com/forum/images/icons/icon10.gif)
hi all , ive just purchased my first sapphire cossie and ive bought it with a possible fooked engine , ive not looked into it fully yet as the car is only getting delivered to me next week but thought i better test the water to see if there are any engines out there as i possibly plan to totally rebuilt the original into a bit of a weapon over a period of time but fancy making the car useable sooner , any help would be appreciated , no doubt ill be after all sorts of bits and advice to help me with the car ,
cheeRS , Danny
cheeRS , Danny
Last edited by bigd2; 25-08-2009 at 06:33 PM. Reason: now got a bottom end
#3
15000
Thread Starter
Join Date: Mar 2006
Location: HEYSHAM NR LANCASTER , LANCS
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
what spec is it ? how much you after ? i should know a bit more tmrw afternoon as to how fooked this one is when it gets delivered to my house.
getting excited now cos its my 1st cossie !!
getting excited now cos its my 1st cossie !!
#6
![Default](https://passionford.com/forum/images/icons/icon1.gif)
hi mate i got an engine for you
t34 turbo
3 bar map sensor
205 block
green injectors
compition paddle clutch
level 6 ecu and relays
loom
320/330bhp
just been run in make me a offer
t34 turbo
3 bar map sensor
205 block
green injectors
compition paddle clutch
level 6 ecu and relays
loom
320/330bhp
just been run in make me a offer
#7
I've found that life I needed.. It's HERE!!
Join Date: Jun 2003
Location: lancaster, northwest england
Posts: 1,078
Likes: 0
Received 0 Likes
on
0 Posts
Trending Topics
#8
15000
Thread Starter
Join Date: Mar 2006
Location: HEYSHAM NR LANCASTER , LANCS
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
right, the car got delivered to me this afternoon i did a compression check and bugger all on cyl 1 so ive whipped the head off and the piston is a bit fooked to say the least and melted to the block , as far as i can see the head is fine , so im looking for a block its currently on a 205 block but open to suggestions ?? full engine if its cheap enough !!!
cheeRS people
cheeRS people
#14
15000
Thread Starter
Join Date: Mar 2006
Location: HEYSHAM NR LANCASTER , LANCS
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
![Unhappy](https://passionford.com/forum/images/icons/icon9.gif)
thanks mate but the bore on no1 is badly scored and upon closer inspection today there is a bad crack from one of the bolt holes so its a full botom end i need !!!
#16
15000
Thread Starter
Join Date: Mar 2006
Location: HEYSHAM NR LANCASTER , LANCS
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
![Talking](https://passionford.com/forum/images/icons/icon10.gif)
thanks for all your help people ive just been and picked up a really good rebuilt bottom end , thanks to TREV_REV , cheers mate and thanks for all the advice !!
Thread
Thread Starter
Forum
Replies
Last Post
FlashRS
Ford RS Cosworth Parts for Sale
13
31-08-2015 06:02 PM