PassionFord - Ford Focus, Escort & RS Forum Discussion
0 2019/03/19 13:56:23
0 2019/03/19 13:56:13
The tyres are in under the inner guards front and rear , she is fully off the ground on the tyres it was a bit scary at first but she never budged once and we flipped her from side to side at will , took 6 guys to lift her each time
The tyres are in under the inner guards front and rear , she is fully off the ground on the tyres it was a bit scary at first but she never budged once and we flipped her from side to side at will , took 6 guys to lift her each time
0 2019/03/19 13:56:03
0 2019/03/19 13:46:57
0 2019/03/19 13:46:47
Once bare and checked always etched in anti corrosion primer straight away
Once bare and checked always etched in anti corrosion primer straight away
0 2019/03/19 13:46:36
Under the left front arch
Under the left front arch
0 2019/03/19 13:46:26
0 2019/03/19 13:46:16
0 2019/03/19 13:46:07
Piece by piece, panel by panel I’m working my way through the entire car
Piece by piece, panel by panel I’m working my way through the entire car
0 2019/03/19 13:45:57
0 2019/03/19 13:45:50
0 2019/03/19 12:54:44
0 2019/03/19 12:54:33
0 2019/03/19 12:54:22
0 2019/03/19 12:54:14
0 2019/03/19 12:54:07
Managed to fit the floor edge and not annoy the chassis number
Managed to fit the floor edge and not annoy the chassis number
0 2019/03/19 12:53:59
0 2019/03/19 12:53:51
0 2019/03/19 12:53:44
This is the inner sill being tried in , the new floor edge is fitted , see how the new inner sill sits on it , when the outer sill goes on the two lips are clamped and spot welded, like factory. It’s the only way to do sills, any metal shop will fold two lengths for a few quid
This is the inner sill being tried in , the new floor edge is fitted , see how the new inner sill sits on it , when the outer sill goes on the two lips are clamped and spot welded, like factory. It’s the only way to do sills, any metal shop will fold two lengths for a few quid
0 2019/03/19 12:53:36
0 2019/03/19 12:45:31
We cut about an inch off the floor and got a folded length of steel right angle the full length to make a new floor outer edge, recommended for spot welding outer sill back on
We cut about an inch off the floor and got a folded length of steel right angle the full length to make a new floor outer edge, recommended for spot welding outer sill back on
0 2019/03/19 12:45:23
0 2019/03/19 12:45:14
Inner silk out
Inner silk out
0 2019/03/19 12:45:06
0 2019/03/19 12:44:58
0 2019/03/19 12:44:50
0 2019/03/19 12:44:42
0 2019/03/19 12:44:33
Sills cut off
Sills cut off
0 2019/03/19 12:44:25
Inner and outer arches cut off
Inner and outer arches cut off
0 2019/03/19 12:44:16
We just had a night where we cut the shit out, front panel and wigs are great so I decided to keep them in , I bought a new front pane and x member, but we only fitted from the headlights down . I’ll show a pic of that job later
We just had a night where we cut the shit out, front panel and wigs are great so I decided to keep them in , I bought a new front pane and x member, but we only fitted from the headlights down . I’ll show a pic of that job later
0 2019/03/19 12:44:08
0 2019/03/19 12:43:41
0 2019/03/19 12:43:17
0 2019/03/19 12:26:25
0 2019/03/19 12:26:15
0 2019/03/19 12:26:01
0 2019/03/19 12:25:43
Added these images again, just to highlight what it looked like , I mean it needs floors ,sills ,inner and outer arches , 2 Chassis legs , rear inner 1/4s front panel and cross member . SERIOUSLY
Added these images again, just to highlight what it looked like , I mean it needs floors ,sills ,inner and outer arches , 2 Chassis legs , rear inner 1/4s front panel and cross member . SERIOUSLY
0 2019/03/19 12:25:31
0 2019/03/19 12:25:15
0 2019/03/19 12:23:07