Just normal nuts will do for me! Also, how long are the studs? I think the standard bolts ar 40 or 50mm? I need them a bit longer if poss...

 

can u get sets for other cars ?? pug 205 for example

 

The longest studs are known as +25mm, they are the 25mm longer than a Standard Ford Stud (as fitted to, for example, a Fiesta) These are the most popular ones, because they can be cut down if necessary.

Up to you which you have.

 

I will look when I get to work.

 

cheeRS mate

 

I'll go for those then.

 

Almost all paid now. I will get these sorted over the weekend. Will hopefully have them out to you by the end of next week.

 

I'll ring tomorrow with my card details.

 

Here is a pic of my old ones if it helps anyone understand. Especially for the question about back clearance



I had to ditch those ones and go for uprated strength ones as im not known for being light on the car

Simple conversion as Christian says

 

CheeRS for that Tony!!

 

Updated above with those that have been posted. I am still awaiting the Lockers, which should arrive with me tomorrow, so the remaining kits will go out either tomorrow or Thursday.

Hope this is OK.

 

All sets were posted today, by Royal Mail. Should arrive Tomorrow/Friday.

Lee, yours was a heavy little b'stard, I will have to courier that one tomorrow. Hope this is OK?

 

i'll have set off ya (16 studs and 12 nuts)but they can't be too long.

cheers

 

thanks mr c they turned up first thing this morning


top service

 

Big thank you to Christian @ APT

My gear also arrived this morning, well packaged too

 

Got mine as well, and my nuts are superb

 

Glad to hear it!!!

 

Hi,

I can do you a set of 16 Studs and 12 Closed Head Chrome Nuts for Ł29.99 Posted. Luckily I ordered a few extra!! Why do you say they cant be too long?

If you want a set, PM me your details (Name, Address, Debit Card Details) and I will get it sorted ASAP.

Thanks.

 

Will you have these in stock in the near future too Christian?

 

Possibly. If not, I can order some more. I like to try and keep it in order-runs though to save carriage, which is how I can keep the price down.

 

well packaged too

i couldnt get into mine, had to get all medevil on it

 

*Visions of Gus throwing the parcel around the room*

PMSL.

 

got mine this morning too
top stuff,cheers mate

 

Arrived today. Thanks Christian!

 

I have a set of AZEV A and they have a very shallow face so i can't have them to long or my center caps won't fit.

Whats the best way for to pay?? Should i send you my details you can send them with my quickshift

 

Stupidly I realised that I actually have all your details already!!! PMSL. However, we need to make sure that you aren't going to have problems. The Closed nuts are quite deep. The Open ones, although they don't look as nice, aren't so deep. Are the nuts totally covered by the centre cap?? If so, I would go for the Open Nuts as you will have a better chance of them clearing the cap.

Alternatively, I can measure the depth of a nut for you tomorrow as that will be more relevant than the length of the stud.

Also, I can't send the Stud/Nut kit with the B&M as thats due to arrive with you tomorrow!! LOL. No problems though.

Thanks for the PM!!

 

The Open nuts are fine. If you can find out the length of nuts and i'll see if they'll fit.

Cheers

 

Christian, can you supply replacement track rod ends??
The steering rack ones.

Currently i have these-->



And would like these--->



Thanks

 

christian,you couldnt do me a favour and tell me what size drill bit to use when drilling the holes?
i used a 13.0 today and the hole turned out too big
cheers mate

 

Oh dear. I cant remember offhand. I think its 12.9. Might be 12.7. Best bet is to measure the shank with a vernier and use a drill thats about 0.2-0.3mm smaller. The other way would be to measure the low point of the splines, as opposed to the high point. Make sense? I will go measure it now.

If you have drilled it too big, it won't be a problem as long as its not sloppy. You can put a blob of weld on the head of the stud to stop the stud from turning in the hub. Its not unsafe as the head stops it from pulling through.

 

thanks mate
i only did one hub,ill put some spots of weld on it,its not sloppy,just a snug fit without having to hammer it in,that should be ok?
thanks for the help

 

Sorry for the delayed reply.



The total length is 25mm from the Tip of the tapered seat to the end of the nut. Hope this makes sense.

 

Just checked and they should be fine mate. You've got my card details so send them out when you can. Please use card i sent on my second PM.


Cheers

 

OK mate. Consider it done.

 

Christian any news on Track rod ends?

 

Cheers mate

 

I can get Rose Joints, but only from a local bearing supplier, which to be honest, you could probably do and get the same price as I could buy them for.

Sorry.

 

Your Stud/Nut kit is ready to go, but I won't get a chance to post it until tomorrow.

Hope that is OK??

 

yea thats fine cheers

 

Got them on friday cheers