T34 Turbo - .63 cool / .63 hot
03-10-2010, 06:03 PM
#1
PassionFord Regular
Thread Starter
iTrader: (2)
Join Date: Mar 2008
Posts: 469
Likes: 0
Received 0 Likes
on
0 Posts
T34 Turbo - .63 cool / .63 hot
Anyone used this config for the T34? If so how laggy is it? I have this setup for my Mk1 Cortina Cossie 4x4 but not sure if she will be too laggy.
03-10-2010, 06:17 PM
#2
laggy compared to what?
t34.63 will make 400hp on the right spec - its an awesome road car set up.
t34.63, ab07 inlet, siemens 55lbs injectors, and a decent chip such as MSD, 2.2bar of boost would see 400hp. be careful of the standard 4x4 gearbox thou, anything beyond 400/400 is a lottery
t34.63 will make 400hp on the right spec - its an awesome road car set up.
t34.63, ab07 inlet, siemens 55lbs injectors, and a decent chip such as MSD, 2.2bar of boost would see 400hp. be careful of the standard 4x4 gearbox thou, anything beyond 400/400 is a lottery
Last edited by LHD220Turbo; 03-10-2010 at 06:18 PM.
03-10-2010, 06:27 PM
#3
On a STD engine to push 400 out of a t34 is asking a little too much and they don't like holding 2.2 bar at high revs, I spike of 2.2 is good but they are Time bombs at that boost iirc mike rain bird done a few t34's pushing over 400 bhp
The .48 is better for a road car IMHO though loose 20 or so hp for more response
The .48 is better for a road car IMHO though loose 20 or so hp for more response
03-10-2010, 06:28 PM
#4
PassionFord Regular
Thread Starter
iTrader: (2)
Join Date: Mar 2008
Posts: 469
Likes: 0
Received 0 Likes
on
0 Posts
What about the bottom end? Its been lightened and balanced but standard pistons and con rod bolts.
I'm after reliability as the car is more of a street sleeper than track / 1/4 mile dragster.
I'm after reliability as the car is more of a street sleeper than track / 1/4 mile dragster.
Last edited by kaisersolsay; 03-10-2010 at 06:31 PM.
but a uprated head gasket is advisable something like a 0611/grp a gasket
03-10-2010, 06:41 PM
#6
PassionFord Regular
Thread Starter
iTrader: (2)
Join Date: Mar 2008
Posts: 469
Likes: 0
Received 0 Likes
on
0 Posts
Yip got a grp A on her. 
Set up is;
0.75 overbore (lighten & balanced cranks, rods, flyweel)
T34 .63 / .63
3 bar MAP
Greens
Pro Alloy 50mm RS500 I/cooler
MSD chip to match above.
What do you think she will put out? Was hoping 350bhp.
Set up is;
0.75 overbore (lighten & balanced cranks, rods, flyweel)
T34 .63 / .63
3 bar MAP
Greens
Pro Alloy 50mm RS500 I/cooler
MSD chip to match above.
What do you think she will put out? Was hoping 350bhp.
Trending Topics
03-10-2010, 07:07 PM
#11
PassionFord Regular
Thread Starter
iTrader: (2)
Join Date: Mar 2008
Posts: 469
Likes: 0
Received 0 Likes
on
0 Posts
May stick with the greens for now as the chip I have matches the kit. You know what like......I'll probably upgrade to light blues and remap after a few weeks!
03-10-2010, 07:16 PM
#12
Too many posts.. I need a life!!
03-10-2010, 07:48 PM
#13
Could always go greys, or as said blues.
T34.48 make a awsome road car around 380 bhp, same as CR turbos used to run in his sapphy, T3/34 makes pick up a little earlier still.
tabetha
T34.48 make a awsome road car around 380 bhp, same as CR turbos used to run in his sapphy, T3/34 makes pick up a little earlier still.
tabetha
Thread
Thread Starter
Forum
Replies
Last Post
Matt Baxter
Ford RS Cosworth Parts for Sale
6
16-09-2015 08:30 PM
kosienutter
General Car Related Discussion.
31
22-08-2015 09:55 AM