S1 Full *CUSTOM* build from shell! *****NOW FINISHED******
#1
S1 Full *CUSTOM* build from shell! *****NOW FINISHED******
Soon to be finished so thought i would share a few shots
This is how it has been sitting for the past year untill now
Group N T3 Hybrid 4x4 Turbo with a De - restriced 34mm. .48 Exhousing. Group N oil feed.
Polished and rounded fuel rail and Cosworth fuel regulator, Yellow injectors, Festo connections to vacum for fuel reg to manifold.
Mk5/6 fuel filter with Festo non rubber connections.
Stainless steel braided fuel lines.
Bailey swirl pot with Samco pipes and Mikalor clamps.
Stainless steel Goodridge water lines and connectors.
STD 1.4 CVH EFi Mk5/6 Black rocker cover, with rubber gasket.
Alloy cam cover washers with stailess counter sunk cap heads bolts.
Another shot of the Group N Turbo
Inlet manifold been smoothed and finished in satin black to match the rocker cover. Fitted with the Water temp convertor, ACT convertor. Stainless lock nuts and stainless water pipes to and from the heater matrix.
THE COIL PACK! 8)
Smoothed inlet manifold. Festo connections. Fuel feed to the rail has a valve making it easy to check fuel pressure.
Brand new Throttle body. Festo connection in the inlet manifold with high pressure lines.
This is how it has been sitting for the past year untill now
Group N T3 Hybrid 4x4 Turbo with a De - restriced 34mm. .48 Exhousing. Group N oil feed.
Polished and rounded fuel rail and Cosworth fuel regulator, Yellow injectors, Festo connections to vacum for fuel reg to manifold.
Mk5/6 fuel filter with Festo non rubber connections.
Stainless steel braided fuel lines.
Bailey swirl pot with Samco pipes and Mikalor clamps.
Stainless steel Goodridge water lines and connectors.
STD 1.4 CVH EFi Mk5/6 Black rocker cover, with rubber gasket.
Alloy cam cover washers with stailess counter sunk cap heads bolts.
Another shot of the Group N Turbo
Inlet manifold been smoothed and finished in satin black to match the rocker cover. Fitted with the Water temp convertor, ACT convertor. Stainless lock nuts and stainless water pipes to and from the heater matrix.
THE COIL PACK! 8)
Smoothed inlet manifold. Festo connections. Fuel feed to the rail has a valve making it easy to check fuel pressure.
Brand new Throttle body. Festo connection in the inlet manifold with high pressure lines.
#5
I checked the engine management today with the ECU from my XR.
Took out the plugs and placed them on the rocker cover while still attached to the leads. So when turning over engine i should see a spark.
Took the plugs off the injectors and using a MK5 escort side light holders in place of the injectors, i can now check that the injectors get a pulse when turning over the engine.
I am yet to run a wire for the fuel pump so instead i connected up a mulitmeter and made sure that the wire was getting 12v with ignition on.
So with no fuel (Cos the injectors are unpluged) and no spark (cos the plugs are on the rocker cover) i turned over the engine and could see the firing order and also the injectors plugs flashing
So the outcome is, that if i have these two parts of the management working and i assume i have compression.......she should start..
I need to take the loom back out and do the final touches to make it fit nice and look nice. Then a little wiring for fuel pumps and triggers etc..
Hope to have her on the road real soon.
Took out the plugs and placed them on the rocker cover while still attached to the leads. So when turning over engine i should see a spark.
Took the plugs off the injectors and using a MK5 escort side light holders in place of the injectors, i can now check that the injectors get a pulse when turning over the engine.
I am yet to run a wire for the fuel pump so instead i connected up a mulitmeter and made sure that the wire was getting 12v with ignition on.
So with no fuel (Cos the injectors are unpluged) and no spark (cos the plugs are on the rocker cover) i turned over the engine and could see the firing order and also the injectors plugs flashing
So the outcome is, that if i have these two parts of the management working and i assume i have compression.......she should start..
I need to take the loom back out and do the final touches to make it fit nice and look nice. Then a little wiring for fuel pumps and triggers etc..
Hope to have her on the road real soon.
#7
PassionFord Post Whore!!
Join Date: Apr 2004
Location: Essex
Posts: 3,759
Likes: 0
Received 0 Likes
on
0 Posts
seen this build all the way through and the attention to detail is bordering on stupidly detailed, things like every clip being individually polished.. should be awsome.
want anymore pics geez? as ive got loads ive been taking along the way
but sod that get on with building my loom mutha fuka!!
want anymore pics geez? as ive got loads ive been taking along the way
but sod that get on with building my loom mutha fuka!!
Trending Topics
#16
PassionFord Post Whore!!
Join Date: May 2004
Location: Near Ipswich.
Posts: 4,976
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by vroooom ptssssh
@ the note
looks minted janno, didnt know them graphics were still avail from ford
looks minted janno, didnt know them graphics were still avail from ford
When i asked a few months ago they wernt.
Looking good though Jano , but FFS sort a decent camera out
#20
Originally Posted by Rossco
Originally Posted by vroooom ptssssh
@ the note
looks minted janno, didnt know them graphics were still avail from ford
looks minted janno, didnt know them graphics were still avail from ford
When i asked a few months ago they wernt.
#29
Thanks to everyone for their kind words
I started her up today with no errors on the management system and will hopefully start to put her back together real soon...
ESSEX RS Reigional day here we come maybe not on the road due to TAX and MOT etc... will trailor it down
Where you been dude aint seen ya for ages!! Get things together and come over
Yes mate he also has a very nice S1 pic below
I started her up today with no errors on the management system and will hopefully start to put her back together real soon...
ESSEX RS Reigional day here we come maybe not on the road due to TAX and MOT etc... will trailor it down
Originally Posted by RS220Turbo
Lovely looking mota there brv hopefully youll have another one to work on soon.
Originally Posted by BillyCabrio
That looks shit hot Jano, i was chatting to one of my mates about you last week. His names Liam, got a S1 - you supplied him all the bits to go cozzie management, hes over the moon
#36
Thanks for the kind words. The car is 90% done now. Still trying to find silly clips and parts like the washer jets and rubber to go around the wiper in the the spoiler etc..
Going back down the breakers today.
Will update with decent pics real soon
Going back down the breakers today.
Will update with decent pics real soon