focos 4x4 its home
10-08-2012, 06:55 PM
#247
Gave the cars a good clean last nite , sadly
The red rst I welded an painted for mate is going
It's new owner tmro ,as we given up on wiring , the
Frs is ready for ford fair an the model a got a bufty aswell
The red rst I welded an painted for mate is going
It's new owner tmro ,as we given up on wiring , the
Frs is ready for ford fair an the model a got a bufty aswell
Last edited by dingla rs; 10-08-2012 at 07:01 PM.
16-08-2012, 04:22 PM
#250
Well after dave jay Ian Andy an few mates gave me grief
Over selling car it's staying I kind of lost intrest after
My thread was deleted as most of my pictures we're lost
But going to get back on with it
Aswell as other things
As always I gave Ian (spacer king colly) my measurement for some spacers
Washers welded together
he made me these , there for
My 300 mm rear brake upgrade to space calipers out for new discs
Big thanks mate
Over selling car it's staying I kind of lost intrest after
My thread was deleted as most of my pictures we're lost
But going to get back on with it
Aswell as other things As always I gave Ian (spacer king colly) my measurement for some spacers
Washers welded together
he made me these , there forMy 300 mm rear brake upgrade to space calipers out for new discs
Big thanks mate
Last edited by dingla rs; 16-08-2012 at 04:23 PM.
19-08-2012, 03:11 PM
#261
had couple hours on it this afternoon after i finished tiling me bathroom at home
got the exhaust sat were i want it now ,not sure if to add a middle braket tho?? , problem i came across was my compstrut braket is very near the down pipe so will have be reworkedand il have run my slave cylinder in car for hydralic clutch as it would boil fluid on the out side .
excuse the welds both my masks are at unit 40miles away
then striped cleaned an painted shafts
dave also sent me these up
as the ones i got off ronnie were fooked waste 15quid
got the exhaust sat were i want it now ,not sure if to add a middle braket tho?? , problem i came across was my compstrut braket is very near the down pipe so will have be reworked
and il have run my slave cylinder in car for hydralic clutch as it would boil fluid on the out side .excuse the welds both my masks are at unit 40miles away
then striped cleaned an painted shafts
dave also sent me these up
as the ones i got off ronnie were fooked waste 15quid
19-08-2012, 03:18 PM
#262
also made a list of things i need to finish it
injectors not sure witch tho ?
3bar map sensor an braket
alloy rad bidding on one
plugs and leads
coil pack
chip for dizzyless set up
powersteering pipes
turbo rebuild
modded trouser piece for external waste gate
intercooler pipe work
they are the main things lots of small bits aswell
slam panel
headlite motors
breather set up
header tank
paint
wheels tyres
ect
injectors not sure witch tho ?
3bar map sensor an braket
alloy rad bidding on one
plugs and leads
coil pack
chip for dizzyless set up
powersteering pipes
turbo rebuild
modded trouser piece for external waste gate
intercooler pipe work
they are the main things lots of small bits aswell
slam panel
headlite motors
breather set up
header tank
paint
wheels tyres
ect
Last edited by dingla rs; 19-08-2012 at 08:12 PM.
19-08-2012, 05:20 PM
#265
PassionFord Post Whore!!
iTrader: (2)
Exhaust looks nice 'n' tight to the floorpan
I've got template to make map sensor bracket if you want one knocking up
Not sure you need a chip to run car dizzyless or do you mean wasted spark ?
To run dizzyless you just need to extend wiring for phase sensor that you moved from dizzy to rear of rocker cover.
glad your back on it m8
I've got template to make map sensor bracket if you want one knocking up
Not sure you need a chip to run car dizzyless or do you mean wasted spark ?
To run dizzyless you just need to extend wiring for phase sensor that you moved from dizzy to rear of rocker cover.
glad your back on it m8
19-08-2012, 05:25 PM
#266
Exhaust looks nice 'n' tight to the floorpan
I've got template to make map sensor bracket if you want one knocking up
Not sure you need a chip to run car dizzyless or do you mean wasted spark ?
To run dizzyless you just need to extend wiring for phase sensor that you moved from dizzy to rear of rocker cover.
glad your back on it m8
I've got template to make map sensor bracket if you want one knocking up
Not sure you need a chip to run car dizzyless or do you mean wasted spark ?
To run dizzyless you just need to extend wiring for phase sensor that you moved from dizzy to rear of rocker cover.
glad your back on it m8
just orderd a braket was only 8 quid dave ,i mean the board that gos in the ecu its 140quid of msd
my engine loom set up for it already
19-08-2012, 08:53 PM
#271
Food to see you 100% back on the car again Andy . It's funny that you have been doing your Exhaust as that's the same job iv been doing this weekend . So I think I'm going to copy your post and put a list up of job to do to finish the car off
pBjBPM8JkkM3w~~60_12.JPG)
