545 bhp Radiant Red Sapphire Cosworth
#521
PassionFord Post Whore!!
Deffo gotta look like a Cossie...
#526
Cheers lads,
As much as i kinda like the sleeper look, It's not staying.
It might be on the road for a short time with the plastic bumpers but its definatly getting the bumpers, skirts and a 4x4 bonnet. The chances are it will be getting a full paintjob over next winter as the paintwork is good but its 24ish years old so not perfect... More money
As much as i kinda like the sleeper look, It's not staying.
It might be on the road for a short time with the plastic bumpers but its definatly getting the bumpers, skirts and a 4x4 bonnet. The chances are it will be getting a full paintjob over next winter as the paintwork is good but its 24ish years old so not perfect... More money
#527
PassionFord Post Whore!!
Sits quite high don't it?
Where's the front grill?
If you do decide to go for a full outer repaint in red I know just the guy for the job...
Where's the front grill?
If you do decide to go for a full outer repaint in red I know just the guy for the job...
Last edited by slammedorion; 19-05-2014 at 10:58 PM.
#528
its settling down a bit, should be fine. its sitting higher on the passenger side at the mo but i guess thats because the suspension geometry is all over the place. I'll have to get the string out and set it up a bit.
Front grile is still upstairs in the office nice and safe, don't want to scratch it while im working in the engine bay.
Front grile is still upstairs in the office nice and safe, don't want to scratch it while im working in the engine bay.
#530
PassionFord Post Whore!!
Will it run this weekend?
I've got 2 new 25 litre fuel drums here if you wanna fill it up with fuel?
I've got 2 new 25 litre fuel drums here if you wanna fill it up with fuel?
#532
Cheers Jon,
No its not running yet. Spent Saturday prepping the Clio for a rally at Abingdon next weekend, then i had to cut the hedge and do a few bit of plumbing on Sunday.
I've managed to do a few little bits though.
Hydraulic clutch is bled up and working, can't believe how light it is
Cleaned and painted the rear ARB with the new droplinks.
I will be upgrading to an escos one at some point but thought i would put it together as is at the moment.
plumbed and wired in the boost control solenoid
tidied up the wiring to the coil
and the gauge holder had got a bit scratched while it was floating around the garage so i gave it a coat of crackle black.
Accelerator and speedo cables are fitted, washer bottle has been swapped for a cossie one that clears the air filter, and the filter has been cleaned and reoiled.
Also got the battery back on. had a few issues as i had somehow lost the excitation feed to the alternator but that's sorted now. ABS seems to be working fine since that's been rewired. Everything else looks good apart from i seem to have lost the wire and plug for the oil pressure switch it will be hidden behind something somewhere
No its not running yet. Spent Saturday prepping the Clio for a rally at Abingdon next weekend, then i had to cut the hedge and do a few bit of plumbing on Sunday.
I've managed to do a few little bits though.
Hydraulic clutch is bled up and working, can't believe how light it is
Cleaned and painted the rear ARB with the new droplinks.
I will be upgrading to an escos one at some point but thought i would put it together as is at the moment.
plumbed and wired in the boost control solenoid
tidied up the wiring to the coil
and the gauge holder had got a bit scratched while it was floating around the garage so i gave it a coat of crackle black.
Accelerator and speedo cables are fitted, washer bottle has been swapped for a cossie one that clears the air filter, and the filter has been cleaned and reoiled.
Also got the battery back on. had a few issues as i had somehow lost the excitation feed to the alternator but that's sorted now. ABS seems to be working fine since that's been rewired. Everything else looks good apart from i seem to have lost the wire and plug for the oil pressure switch it will be hidden behind something somewhere
Last edited by fraser9764; 02-06-2014 at 09:22 AM.
#534
PassionFord Post Whore!!
Have you sorted getting a front bumper off Nash yet?
#535
PassionFord Post Whore!!
#537
PassionFord Post Whore!!
Getting plenty of practice...
Still bumpers and side skirts to do...
Get the spoiler done, then it's time to freshen up the Hocks...
Still bumpers and side skirts to do...
Get the spoiler done, then it's time to freshen up the Hocks...
#538
PassionFord Post Whore!!
#541
PassionFord Post Whore!!
#542
PassionFord Post Whore!!
Graham's been round tonight and caught me flatting the spoiler again...
There was a couple of bits I wasn't happy with... Nowt really, but I've started flatting again with 800... Wants alittle more flatting and will paint it again after work tomorrow...
Gun finish is great, just had a couple of areas where the primers sunk allowing me to see the odd prepping mark under the paint...
It's no big deal, atleast it'll be super flat after the next hit...
There was a couple of bits I wasn't happy with... Nowt really, but I've started flatting again with 800... Wants alittle more flatting and will paint it again after work tomorrow...
Gun finish is great, just had a couple of areas where the primers sunk allowing me to see the odd prepping mark under the paint...
It's no big deal, atleast it'll be super flat after the next hit...
#543
Well she runs at last! Put all the fluids etc in yesterday and it started first turn of the key
The brakes took a fair bit of bleeding but got there in the end,
Got a small oil leak to fix from the breather oil return. No problem just a pain in the ass.
The biggest problem is the clutch won't disengage hydro clutch is working perfectly but the clutch doesnt even try to release. I think its by fault for either somehow fitting the clutch plate back to front, or maybe its because I didnt grease the input shaft. Either way it looks like the box is coming back out
The brakes took a fair bit of bleeding but got there in the end,
Got a small oil leak to fix from the breather oil return. No problem just a pain in the ass.
The biggest problem is the clutch won't disengage hydro clutch is working perfectly but the clutch doesnt even try to release. I think its by fault for either somehow fitting the clutch plate back to front, or maybe its because I didnt grease the input shaft. Either way it looks like the box is coming back out
#544
PassionFord Post Whore!!
All sorted yet?
#545
Well the car is pretty much mechanically complete
Turns out i had a bit of a brain fart when i fitted the clutch and put the friction plate in back to front
anyway thats all sorted now, so if i put the wheels on and drop it off the stands it will drive
but I'm not doing that because ive just ordered a set of gaz golds
should be here tomorrow or thursday so first drive this weekend hopefully.
Turns out i had a bit of a brain fart when i fitted the clutch and put the friction plate in back to front
anyway thats all sorted now, so if i put the wheels on and drop it off the stands it will drive
but I'm not doing that because ive just ordered a set of gaz golds
should be here tomorrow or thursday so first drive this weekend hopefully.
#546
PassionFord Post Whore!!
#547
engine bay complete, just needs a bit of a clean.
fitted an inlet manifold damper/bracket. never had one on the old car but for the tenner or so it cost its worth it for peace of mind.
Gaz Golds turned up yesterday so got 2 fitted last night. will get the other 2 on this afternoon.
Picked up a couple of rear tyres the other night off Ridgey so ive got 235x40r17 Federal RS-R's for the rear, and ive ordered a set of 215x40r17s for the front. Hopefully these will be delivered next week so tax from the first and see how it drives
fitted an inlet manifold damper/bracket. never had one on the old car but for the tenner or so it cost its worth it for peace of mind.
Gaz Golds turned up yesterday so got 2 fitted last night. will get the other 2 on this afternoon.
Picked up a couple of rear tyres the other night off Ridgey so ive got 235x40r17 Federal RS-R's for the rear, and ive ordered a set of 215x40r17s for the front. Hopefully these will be delivered next week so tax from the first and see how it drives
Last edited by fraser9764; 27-06-2014 at 11:10 AM.
#552
PassionFord Post Whore!!
Tonight I've painted the lip on the spoiler satin black.
I scotched the lip, edging taped down yet groove, put some blue tape which is less sticky over the edging tape. Then masked and covered the rest with news paper.
During painting the lip...
After peeling the tape off it looks like so...
And placed the caps over the holes just to check the colour...
Needs a light flat and polish one fitted to the bootlid.
But I'm pretty please with the finish out of the gun.
Bumpers and side skirts to do before Fordfair...
I scotched the lip, edging taped down yet groove, put some blue tape which is less sticky over the edging tape. Then masked and covered the rest with news paper.
During painting the lip...
After peeling the tape off it looks like so...
And placed the caps over the holes just to check the colour...
Needs a light flat and polish one fitted to the bootlid.
But I'm pretty please with the finish out of the gun.
Bumpers and side skirts to do before Fordfair...
#554
PassionFord Post Whore!!
It's gonna look awesome rolling down to Fordfair...
It's been worth taking the time to get it right...
It's been worth taking the time to get it right...