(COLEYST200) focus to focos / skyline gear box
09-01-2011, 01:18 PM
#888
WRC S1cos coming soon!!!
Join Date: Jan 2009
Location: At work
Posts: 819
Likes: 0
Received 0 Likes
on
0 Posts
12-01-2011, 09:21 PM
#890
only a small one today me and Dave were chatting last night about some thing i was thinking about doing well iv done it and i love it
And sam was round the weekend and has started to stip the car back down so i can finish all the welding of
And sam was round the weekend and has started to stip the car back down so i can finish all the welding of
12-01-2011, 10:07 PM
#897
12-01-2011, 10:18 PM
#898
yes they do but this is why iv been moking the car up as right behind the clocks you have a beam to mod to get the speedo cable throw then behind that the shell has i big bilt in box box section very had to get throw and the speedo cable has got to get to the N/S any way so iv run it behind the dash and heater the broke out on the N/S and straight onto the side of the sump as it a 4x4 set up
14-01-2011, 10:40 PM
#902
Done a bit tonight on the shell as on the way home i got some new sills as there is a bit of rot on them and the drivers side has been jacked up on a lot so that one will take a bit of time to sort out but im very happy with wot i got done to night
ITS ONLY HELD IN PLACE FOR THE PHOTO AS I NEED TO SORT A SMALL BIT OF RUST OUT FIRST BEFOR THE NEW SILL GOSE ON
ITS ONLY HELD IN PLACE FOR THE PHOTO AS I NEED TO SORT A SMALL BIT OF RUST OUT FIRST BEFOR THE NEW SILL GOSE ON
15-01-2011, 10:53 AM
#907
PassionFord Post Whore!!
iTrader: (2)
Dont i know about it
I had a bollocking of the bride the last time i was popping up your's for ten mins i didnt get home till 12
still better than watching east enders and im a celebrity and i cor dance ay?
Good progres on the car M8
wish i had half as much spare time as you
15-01-2011, 10:33 PM
#908
Iv do a bit more tonight i got the drivers side sill all cut off and the repairs done to the lip were it had been jacked up on
And i gave SAM a hand to get the motor out he did most of the work so THANKS SAM for your help over the last to nights
And i gave SAM a hand to get the motor out he did most of the work so THANKS SAM for your help over the last to nights
15-01-2011, 11:10 PM
#910
list
weld the sills on
beef up the hand break
weld up the holes were the front cradle bolt on
weld up the holes inside were the ARB bolts up
weld up the holes in the floor were the shell has plastic drain bungs
weld up the under side of the front top mounts
flash all the welds with a grinder
get a cage and weld it in but if i do it i will need a new welder
then it might do time to do a bit of prep work
weld the sills on
beef up the hand break
weld up the holes were the front cradle bolt on
weld up the holes inside were the ARB bolts up
weld up the holes in the floor were the shell has plastic drain bungs
weld up the under side of the front top mounts
flash all the welds with a grinder
get a cage and weld it in but if i do it i will need a new welder
then it might do time to do a bit of prep work
16-01-2011, 12:17 AM
#912
that would be very good of you mate as if i do weld it iv got to use a percific wire
Specification:
High tensile wire suitable welding wire for T45 roll cage tube.
Kit consists of:
3kg roll sufficient for completing one roll cage. ER 100 S-G grade.
Price: Ł44.85 + VAT
Specification:
High tensile wire suitable welding wire for T45 roll cage tube.
Kit consists of:
3kg roll sufficient for completing one roll cage. ER 100 S-G grade.
Price: Ł44.85 + VAT
16-01-2011, 12:13 PM
#917
Its not up to me ANDY its wot Custom Cages make there cages out of . and thats the wire they say you need to use if you mig it togever . have a look mate they do all so talk about CDS tubing
http://www.customcages.co.uk/homepage
http://www.customcages.co.uk/homepage
