MEV. 320bhp Jamsport built s2 rs turbo
#82
PassionFord Post Whore!!
Thread Starter
Think comp Th's or th2's it will be, now just gotta decide on colour, white, anthercite or black hmmm
Last edited by jaiscossie; 06-03-2010 at 09:06 AM.
#83
PassionFord Post Whore!!
iTrader: (12)
but to keep it simple and a tidy handling car 16"s would be ok but just pricey on tyres
and as for the colour anthracite gets my vote,but you should now keep within the colour scheme you have
#84
PassionFord Post Whore!!
Thread Starter
The cars running konis with -30mm cobra springs, S1 arb setup, and fully polybushed.
Gonna look into 16" th's or th2's i think then in black with a decent tyre (something not as pricey and will last a little longer than 888s) Perhaps the t1r's your said about or pradas
Last edited by jaiscossie; 06-03-2010 at 10:20 AM.
#87
PassionFord Post Whore!!
Thread Starter
Got the car back from Tom at Tem sport and am really pleased with the work he has done.The car goes and idles so much better now.He also fitted a proper braided fuel line rather than the old rubber hose it had with jubalee clips.Got my oil pressure gauge working, removed my fuel accumalator and relocated the fuel filter,fitted a new towing eye as didnt have one (just incase)Fitted a new throttle cable also as the other was kinked.Put some proper fully synthetic top notch gearbox oil in to hopefully help a bit and adjusted my sollid tappets which are pretty silent now.
I got hold of another pair of bonnet vents and have done them satin black.What do you guys think.
I got hold of another pair of bonnet vents and have done them satin black.What do you guys think.
Last edited by jaiscossie; 21-03-2010 at 06:36 PM.
#91
PassionFord Post Whore!!
Thread Starter
#93
Advanced PassionFord User
don't mean to sound out of place but did they or you flow test that inlet as i'd be concerned at number 1 not getting equal air to the others as the flow of air is moving way from number 1 apart from that car looks good but not to keen on the black bits
#95
PassionFord Post Whore!!
Thread Starter
#96
PassionFord Post Whore!!
Thread Starter
Yes mate its been flow tested and pressure tested to 5 bar so shouldnt have any problems this time around
#97
PassionFord Post Troll
iTrader: (3)
Join Date: Jan 2005
Location: Bristol/Bath
Posts: 2,568
Likes: 0
Received 0 Likes
on
0 Posts
Looking at your pics it's because the bonnet raisers have been put in the holes where the rubber bump stops normally go......meaning your bonnet is sat on the slam panel, if you get some stiff rubber hose to go over your bonnet pins and cut it to the right length/raise your bonnet pins you could space it up a bit mate
#98
PassionFord Post Whore!!
Thread Starter
Looking at your pics it's because the bonnet raisers have been put in the holes where the rubber bump stops normally go......meaning your bonnet is sat on the slam panel, if you get some stiff rubber hose to go over your bonnet pins and cut it to the right length/raise your bonnet pins you could space it up a bit mate
#103
PassionFord Post Whore!!
Thread Starter
As my dash has been flocked (albeit professionaly) i thought id have a go at doing a few small bits myself.Started off with the interior door handles and mirror covers as they were looking a bit tatty.Am pretty pleased for my first go, is a bit messy doing it though and is probably a good idea to wear a mask as i didnt and had black bogies today!!
Here are the bits i did last night.
Here are the bits i did last night.
#108
PassionFord Post Whore!!
Thread Starter
#111
PassionFord Post Whore!!
Thread Starter
Cheers mate, will be going to most of them as normally do.Will be on the suffok/essex stand at central day.
#114
PassionFord Post Whore!!
Thread Starter
Done a few more bits and pieces over the last few days as the weathers been good
Fitted my custom made gearknob which i had machined up based on the nylon Quaife one they do
Nice new braided fuel hose fitted with proper end clamps this time (not jubaliee clips and rubber hose!!!)
Relocated the map sensor as was previously on the inner wing and was worried it may get wet (not that the car ever really gets wet lol)
My flocked mirror adjuster covers i did myself, quite pleased how they came out.
Added padding to the cage
Proper towing eye fitted (thanks Tom)
Few more decals fitted
And finally my fav picture of the car so far
Fitted my custom made gearknob which i had machined up based on the nylon Quaife one they do
Nice new braided fuel hose fitted with proper end clamps this time (not jubaliee clips and rubber hose!!!)
Relocated the map sensor as was previously on the inner wing and was worried it may get wet (not that the car ever really gets wet lol)
My flocked mirror adjuster covers i did myself, quite pleased how they came out.
Added padding to the cage
Proper towing eye fitted (thanks Tom)
Few more decals fitted
And finally my fav picture of the car so far
#117
PassionFord Post Whore!!
Thread Starter
#119
Advanced PassionFord User
don't suppose you have the flow figures do you be interesting to see how much variance there is across the 4 runners as not a lot of companys do it as there lazy and with out them being tested you could be wasting money/time and power if not up to the job