New pics of my 50K mile Sierra Cosworth
02-12-2008 | 12:00 AM
#41
Thread Starter
PassionFord Post Whore!!
iTrader: (4)
Joined: May 2004
Posts: 7,886
Likes: 35
From: Bangor, Northern Ireland
I haven't decided 100% what spec to go for, but I know I'll need the transmission/suspension/brakes properly sorted before I up the power any more! I know the bottom end will have 10 longstuds, nikasil liners and oil jet mods, but thats it lol. I really bad when it comes to making up my mind on things like this 
02-01-2009 | 07:12 PM
#45
Thread Starter
PassionFord Post Whore!!
iTrader: (4)
Joined: May 2004
Posts: 7,886
Likes: 35
From: Bangor, Northern Ireland
Small update, finally fitted my modified escort cossie airbox
It has a Rainbird 76mm adaptor, K&N and the front is cut out to aid air flow.
Pics are crappy as the light was fading when i took them (Roll on summer!!!)
I'll maybe get some better ones tomorrow if i can be arsed
It has a Rainbird 76mm adaptor, K&N and the front is cut out to aid air flow.
Pics are crappy as the light was fading when i took them (Roll on summer!!!)
I'll maybe get some better ones tomorrow if i can be arsed
20-04-2009 | 09:30 PM
#63
Thread Starter
PassionFord Post Whore!!
iTrader: (4)
Joined: May 2004
Posts: 7,886
Likes: 35
From: Bangor, Northern Ireland
Cheers dude
Hopefully be a few changes within the next month or so
Bara box with all the options including a centre push hydraulic conversion
ATB thickwall front diff
Harvey 6 degree beam
New drivers seat
330mm AP 4 pots up front
300mm rear disc conversion
I can't fucking wait!!
Just leaves the car wanting proper suspension and a proper engine lol
Hopefully be a few changes within the next month or so
Bara box with all the options including a centre push hydraulic conversion
ATB thickwall front diff
Harvey 6 degree beam
New drivers seat
330mm AP 4 pots up front
300mm rear disc conversion
I can't fucking wait!!
Just leaves the car wanting proper suspension and a proper engine lol
13-05-2009 | 05:57 PM
#64
Thread Starter
PassionFord Post Whore!!
iTrader: (4)
Joined: May 2004
Posts: 7,886
Likes: 35
From: Bangor, Northern Ireland
Another update-
Got a set of AP CP5200 4 pots and 330mm discs. Also have a rear 300mm conversion, but there's no point fitting it until i'm fitting the 6 degree rear beam.
Hopefully picking up the bits listed in the post above this weekend as well
Got a set of AP CP5200 4 pots and 330mm discs. Also have a rear 300mm conversion, but there's no point fitting it until i'm fitting the 6 degree rear beam.
Hopefully picking up the bits listed in the post above this weekend as well
17-05-2009 | 01:42 AM
#71
Thread Starter
PassionFord Post Whore!!
iTrader: (4)
Joined: May 2004
Posts: 7,886
Likes: 35
From: Bangor, Northern Ireland
Only got the seat and gearbox fitted tonight.
Massive thanks to Mark for bulling it in
Few of the bits we collected today-
Bara Gearbox > Straight cut first second third and fifth, standard fourth.
Bit beefier than standard:P
Mongoose exhaust-
Recaro Pole position seat trimmed in leather with Willans harnesses
Ahmed Bajoo 6 degree beam (improves traction)
Hydraulic clutch conversion and B&M shortshift
Rear Strut Brace
Quaife Thickwall ATB front diff
Waiting on a few bits arriving before the diff can be fitted. Will need to mod the exhaust slightly to get it to sit well when using the 6 degree beam.
Chuffed is an understatement:P
Massive thanks to Mark for bulling it in
Few of the bits we collected today-
Bara Gearbox > Straight cut first second third and fifth, standard fourth.
Bit beefier than standard:P
Mongoose exhaust-
Recaro Pole position seat trimmed in leather with Willans harnesses
Ahmed Bajoo 6 degree beam (improves traction)
Hydraulic clutch conversion and B&M shortshift
Rear Strut Brace
Quaife Thickwall ATB front diff
Waiting on a few bits arriving before the diff can be fitted. Will need to mod the exhaust slightly to get it to sit well when using the 6 degree beam.
Chuffed is an understatement:P
