Big Up RYAN - nice loom!!!!!!!! :banana:
#43
Chasing Radders
Originally Posted by ImaRacing 700
TIFANNY,can we have the hob knobs and a cup of tea please ROFL
Here you go mate, Been at work and just seen the post
Get dunking peeps
#44
I've found that life I needed.. It's HERE!!
Looking good How do you do the labelling Ryan? Is it a special see-through heatshrink?
Just one more question: Where is the big rubber grommet for where the loom passes through the bulkhead?
Just one more question: Where is the big rubber grommet for where the loom passes through the bulkhead?
#46
15K+ Super Poster!!
Join Date: May 2003
Location: Southampton
Posts: 18,589
Likes: 0
Received 0 Likes
on
0 Posts
Wes i bought a Thermal printer, not fooookin cheap
It prints onto heatshrink and then clear heatshrink is put over the top for protection against abrasion.
Wes, unfortauntely the grommits are no longer available from fords i've had all my contacts looking high and low for them, so the current solution is to use the existing one.
Until i can find a better solution.
Pectel Looms have the genuine ford grommit but i think either they've bought up the remainder of the stock or they get them made especially. Either way i think they would be a bit reluctant to sell me 50
It prints onto heatshrink and then clear heatshrink is put over the top for protection against abrasion.
Wes, unfortauntely the grommits are no longer available from fords i've had all my contacts looking high and low for them, so the current solution is to use the existing one.
Until i can find a better solution.
Pectel Looms have the genuine ford grommit but i think either they've bought up the remainder of the stock or they get them made especially. Either way i think they would be a bit reluctant to sell me 50
#47
I've found that life I needed.. It's HERE!!
Thanks for the info Ryan
When i made my loom, i couldn't source that grommet either, so i reused the original, however i had to put the wires through the grommet before fully assembling the loom as there was no way i was getting either all of the engine connectors or the ecu connector through it, without having to modify the grommet i.e. cutting a big hole in it
When i made my loom, i couldn't source that grommet either, so i reused the original, however i had to put the wires through the grommet before fully assembling the loom as there was no way i was getting either all of the engine connectors or the ecu connector through it, without having to modify the grommet i.e. cutting a big hole in it
#48
15K+ Super Poster!!
Join Date: May 2003
Location: Southampton
Posts: 18,589
Likes: 0
Received 0 Likes
on
0 Posts
simple single cut from the outer to the inside of the grommit.
Slip the loom out slide the new one in
Once reinstalled you would never know
Im sure i find a suitable solution soon
Slip the loom out slide the new one in
Once reinstalled you would never know
Im sure i find a suitable solution soon
#49
PassionFord Post Whore!!
Join Date: May 2003
Location: Doncaster
Posts: 5,143
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Ryan
simple single cut from the outer to the inside of the grommit.
Slip the loom out slide the new one in
Once reinstalled you would never know
Im sure i find a suitable solution soon
Slip the loom out slide the new one in
Once reinstalled you would never know
Im sure i find a suitable solution soon
got to be better than tim using a cv joint gator
Thread
Thread Starter
Forum
Replies
Last Post
DixieTheKid
Ford Sierra/Sapphire/RS500 Cosworth
11
06-06-2020 11:20 AM