YET ANOTHER BIG POWER ENGINE ON SECS S8 ECU - 632 BHP
#1
BANNED
BANNED
Thread Starter
iTrader: (1)
Join Date: Jul 2003
Location: Wiltshire
Posts: 12,483
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Sorry everyone this is a blatent advert for me and a few others....
This afternoon, my friend Nick Lewis (a NEW PF user NIL 7090)
had his cosworth YB engine dynoed at Norris Designs.
The engine specification is as follows....
ENGINE SPECED/BUILT BY NORRIS DESIGNS (DAVE MIDGLEY / SIMON NORRIS / NICK LEWIS)
MAPPED BY SIMON NORRIS
HEAD PORTING AND TEA MAKING BY SPENCER ATHAY (aka PF spenner)
CAPACITY 2.0 LITRES
JE PISTONS TO NORRIS DESIGNS SPEC.
COMPRESSION RATIO (NOT DISCLOSED)
4 x 1000cc SARD FUEL INJECTORS
SWEDISH INLET MANIFOLD (SUPPLIED BY MIKE RAINBIRD)
METRO 6R4 THROTTLE BODY
GARRET GT30/40 HYBRID WITH EXTERNAL WASTEGATE
BOOST LIMITED TO 2.0 BAR AT ALL TIMES ELECTRONICALLY
8200 rpm REV LIMIT
PORTED HEAD (STANDARD SIZE VALVES)
CAMS NORRIS DESIGNS SPEC.
CAM VERNIERS
SOLID LIFTERS
LONG STUDDED HEAD BOLTS
METAL 3 LAYER HEAD GASKET
LIGHTENED FLYWHEEL
BLUE PRINTED AND BALANCED CRANK/RODS
HIGH FLOW PISTON OIL JETS
OIL COOLER
SPEC R CUSTOMISED 4 PORT BREATHER SYSTEM
ALLOY CRANK PULLEY WITH IRON LUGS FOR CRANK SENSOR
SECS S8 ENGINE MANAGMENT
SECS S8 COIL PACK IGNITION SYSTEM
5 BAR MAP SENSOR
CLOSED LOOP LAMBDA FUELLING (NOT AT FULL LOAD)
The engine was initialy started and mapped for idle and acheives a stable idle
at 1000 rpm with a lambda reading of 1.00 (AFR 14.7:1)
Then the engine was fully mapped with a flat line controlled maximum boost of 2.0 Bar.
The fuel was then changed for race fuel and the ignition table modified and then
a second maping session with power run was made.
I wanted them to run a bit more boost personally but the engine was mapped conservativley
due to Nick shitting him self and not wanting to rebuild it too often !
I must say I have rarely seen such a flat torque curve as on this engine and remember
it is torque that gives acceleration.
Just remember, this is ONLY still a 2.0 litre and does NOT run NOS.
I cannot give any further specifications/details as these were not given to me and/or
the engine builders were keeping it a bit quiet.
The results....
PUMP FUEL 97 RON: 584 bhp @ 7440 rpm / 450 lb/ft @ 6090 rpm
RACE FUEL 118 RON: 632 bhp @ 7650 rpm / 474 lb/ft @ 6040 rpm
I have posted a few piccys....
PUMP FUEL: POWER RUN GRAPH
![](http://www.s8ecu.co.uk/graph1.jpg)
PUMP FUEL: POWER DATA TABLE (LAMBDA READINGS ARE NOT CORRECT HERE)
![](http://www.s8ecu.co.uk/table11.jpg)
PUMP FUEL: PRESSURES DATA TABLE
![](http://www.s8ecu.co.uk/table12.jpg)
RACE FUEL: POWER RUN GRAPH
![](http://www.s8ecu.co.uk/graph2.jpg)
RACE FUEL: POWER DATA TABLE (LAMBDA READINGS ARE NOT CORRECT HERE)
![](http://www.s8ecu.co.uk/table2.jpg)
PICTURES OF THE ENGINE ON THE DYNO CHASSIS
![](http://www.s8ecu.co.uk/dyno1.jpg)
![](http://www.s8ecu.co.uk/dyno2.jpg)
![](http://www.s8ecu.co.uk/dyno3.jpg)
![](http://www.s8ecu.co.uk/dyno4.jpg)
![](http://www.s8ecu.co.uk/dyno5.jpg)
NICK PRETENDING TO BE A MAPPER
![](http://www.s8ecu.co.uk/nick.jpg)
Bugger, forgot to get pictures of ECU
Thanks to Nick Lewis and Simon Norris for putting faith in the S8![Top](https://passionford.com/forum/images/smilies/smile011.gif)
Right, let the put downs comence .....
This afternoon, my friend Nick Lewis (a NEW PF user NIL 7090)
had his cosworth YB engine dynoed at Norris Designs.
The engine specification is as follows....
ENGINE SPECED/BUILT BY NORRIS DESIGNS (DAVE MIDGLEY / SIMON NORRIS / NICK LEWIS)
MAPPED BY SIMON NORRIS
HEAD PORTING AND TEA MAKING BY SPENCER ATHAY (aka PF spenner)
CAPACITY 2.0 LITRES
JE PISTONS TO NORRIS DESIGNS SPEC.
COMPRESSION RATIO (NOT DISCLOSED)
4 x 1000cc SARD FUEL INJECTORS
SWEDISH INLET MANIFOLD (SUPPLIED BY MIKE RAINBIRD)
METRO 6R4 THROTTLE BODY
GARRET GT30/40 HYBRID WITH EXTERNAL WASTEGATE
BOOST LIMITED TO 2.0 BAR AT ALL TIMES ELECTRONICALLY
8200 rpm REV LIMIT
PORTED HEAD (STANDARD SIZE VALVES)
CAMS NORRIS DESIGNS SPEC.
CAM VERNIERS
SOLID LIFTERS
LONG STUDDED HEAD BOLTS
METAL 3 LAYER HEAD GASKET
LIGHTENED FLYWHEEL
BLUE PRINTED AND BALANCED CRANK/RODS
HIGH FLOW PISTON OIL JETS
OIL COOLER
SPEC R CUSTOMISED 4 PORT BREATHER SYSTEM
ALLOY CRANK PULLEY WITH IRON LUGS FOR CRANK SENSOR
SECS S8 ENGINE MANAGMENT
SECS S8 COIL PACK IGNITION SYSTEM
5 BAR MAP SENSOR
CLOSED LOOP LAMBDA FUELLING (NOT AT FULL LOAD)
The engine was initialy started and mapped for idle and acheives a stable idle
at 1000 rpm with a lambda reading of 1.00 (AFR 14.7:1)
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
Then the engine was fully mapped with a flat line controlled maximum boost of 2.0 Bar.
The fuel was then changed for race fuel and the ignition table modified and then
a second maping session with power run was made.
I wanted them to run a bit more boost personally but the engine was mapped conservativley
due to Nick shitting him self and not wanting to rebuild it too often !
I must say I have rarely seen such a flat torque curve as on this engine and remember
it is torque that gives acceleration.
Just remember, this is ONLY still a 2.0 litre and does NOT run NOS.
![Pthbbbb](https://passionford.com/forum/images/smilies/smile045.gif)
I cannot give any further specifications/details as these were not given to me and/or
the engine builders were keeping it a bit quiet.
The results....
PUMP FUEL 97 RON: 584 bhp @ 7440 rpm / 450 lb/ft @ 6090 rpm
RACE FUEL 118 RON: 632 bhp @ 7650 rpm / 474 lb/ft @ 6040 rpm
I have posted a few piccys....
PUMP FUEL: POWER RUN GRAPH
![](http://www.s8ecu.co.uk/graph1.jpg)
PUMP FUEL: POWER DATA TABLE (LAMBDA READINGS ARE NOT CORRECT HERE)
![](http://www.s8ecu.co.uk/table11.jpg)
PUMP FUEL: PRESSURES DATA TABLE
![](http://www.s8ecu.co.uk/table12.jpg)
RACE FUEL: POWER RUN GRAPH
![](http://www.s8ecu.co.uk/graph2.jpg)
RACE FUEL: POWER DATA TABLE (LAMBDA READINGS ARE NOT CORRECT HERE)
![](http://www.s8ecu.co.uk/table2.jpg)
PICTURES OF THE ENGINE ON THE DYNO CHASSIS
![](http://www.s8ecu.co.uk/dyno1.jpg)
![](http://www.s8ecu.co.uk/dyno2.jpg)
![](http://www.s8ecu.co.uk/dyno3.jpg)
![](http://www.s8ecu.co.uk/dyno4.jpg)
![](http://www.s8ecu.co.uk/dyno5.jpg)
NICK PRETENDING TO BE A MAPPER
![](http://www.s8ecu.co.uk/nick.jpg)
Bugger, forgot to get pictures of ECU
![Wall](https://passionford.com/forum/images/smilies/wall.gif)
Thanks to Nick Lewis and Simon Norris for putting faith in the S8
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
Right, let the put downs comence .....
![Sad](https://passionford.com/forum/images/smilies/icon_sad.gif)
Trending Topics
#11
BANNED
BANNED
Thread Starter
iTrader: (1)
Join Date: Jul 2003
Location: Wiltshire
Posts: 12,483
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Originally Posted by Paul Eggleton
Fair fucking play. Nice one.
I didn't realise just porting the head would allow it to flow enough to reach that power.![Confused](https://passionford.com/forum/images/smilies/icon_confused.gif)
I didn't realise just porting the head would allow it to flow enough to reach that power.
![Confused](https://passionford.com/forum/images/smilies/icon_confused.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
#12
BANNED
BANNED
Thread Starter
iTrader: (1)
Join Date: Jul 2003
Location: Wiltshire
Posts: 12,483
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Originally Posted by Karl
Superb Simon. As you say would have been great to run a touch more boost.
I think the torque curve is fantastic!![Top](https://passionford.com/forum/images/smilies/smile011.gif)
I think the torque curve is fantastic!
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
makes such a statement.
Unfortunately, I can only take credit for the ECU system.
#14
PassionFord Post Whore!!
Join Date: Jun 2003
Location: Saving the planet
Posts: 5,749
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Originally Posted by SECS
Originally Posted by Paul Eggleton
Fair fucking play. Nice one.
I didn't realise just porting the head would allow it to flow enough to reach that power.![Confused](https://passionford.com/forum/images/smilies/icon_confused.gif)
I didn't realise just porting the head would allow it to flow enough to reach that power.
![Confused](https://passionford.com/forum/images/smilies/icon_confused.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Big Grin](https://passionford.com/forum/images/smilies/icon_biggrin.gif)
#17
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Some stats:
Add together the BHP output of Porkie's, Brom's and Nick's engines - ALL running SECS S8....and you got 1,856 BHP
Then add Phils DIY engine (488 BHP) ??????? whats the total for the four engines?
2,344 BHP ???
Add together the BHP output of Porkie's, Brom's and Nick's engines - ALL running SECS S8....and you got 1,856 BHP
Then add Phils DIY engine (488 BHP) ??????? whats the total for the four engines?
2,344 BHP ???
![Surprised](https://passionford.com/forum/images/smilies/shocked.gif)
#21
BANNED
BANNED
Thread Starter
iTrader: (1)
Join Date: Jul 2003
Location: Wiltshire
Posts: 12,483
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Originally Posted by RWD_cossie_wil
is very impressive
any idea on the crank just for interests sake?
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
tension relieved by shot peening.
#23
Regular Contributor
Join Date: Aug 2003
Location: wilts
Posts: 322
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
WHAT A TOP RESULT
ALSO VERY QUIET ENGINE AT HIGH REVS SOUNDED LOVELY WELL DONE NICK MINES NEXT OH BUGGER
WELL DONE NORRIE WHAT A PUKKA JOB AND DAVE TOP ENGINE BUILDER AND SIMONS E.C.U IS THE DANGLIES
BOUNDARIES ARE NOW BEING PUSHED 700 THE NEXT MILESTONE WITHOUT NOS ANY TAKERS
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Confused](https://passionford.com/forum/images/smilies/icon_confused.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
#24
BANNED
BANNED
Thread Starter
iTrader: (1)
Join Date: Jul 2003
Location: Wiltshire
Posts: 12,483
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Originally Posted by timrud
What car is it going in? 2wd or 4wd?
Immense torque curve!![Top](https://passionford.com/forum/images/smilies/smile011.gif)
Immense torque curve!
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
Dont know what type this will be though.
#26
PassionFord Post Whore!!
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Simon I bet Nicks happy
Cant wait till he starts going to the shootouts will be very fast,
You may want to edit and put in Who did the head work as you never know who will take the credit
.
Mark
![Content](https://passionford.com/forum/images/smilies/content.gif)
You may want to edit and put in Who did the head work as you never know who will take the credit
![Surprised](https://passionford.com/forum/images/smilies/shocked.gif)
Mark
#30
BANNED
BANNED
Thread Starter
iTrader: (1)
Join Date: Jul 2003
Location: Wiltshire
Posts: 12,483
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Originally Posted by madevelopments
Simon I bet Nicks happy
Cant wait till he starts going to the shootouts will be very fast,
You may want to edit and put in Who did the head work as you never know who will take the credit
.
Mark
![Content](https://passionford.com/forum/images/smilies/content.gif)
You may want to edit and put in Who did the head work as you never know who will take the credit
![Surprised](https://passionford.com/forum/images/smilies/shocked.gif)
Mark
It was that chap "spenner" who did the head job
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
#34
BANNED
BANNED
Thread Starter
iTrader: (1)
Join Date: Jul 2003
Location: Wiltshire
Posts: 12,483
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Originally Posted by RWD_cossie_wil
DONT TURN THIS INTO TUNER WARS FFS
![Mad](https://passionford.com/forum/images/smilies/mad.gif)
![Mad](https://passionford.com/forum/images/smilies/mad.gif)
![Mad](https://passionford.com/forum/images/smilies/mad.gif)
![Mad](https://passionford.com/forum/images/smilies/mad.gif)
![Mad](https://passionford.com/forum/images/smilies/mad.gif)
no one else cant do the same !
![Big Grin](https://passionford.com/forum/images/smilies/icon_mrgreen.gif)
#36
PassionFord Post Whore!!
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Yes I forgot Spenncer did the head
He always makes the tea
, Cant wait till he goes for 1/4mile and top speed It should be on for 195+mph
.
Mark
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Big Grin](https://passionford.com/forum/images/smilies/icon_mrgreen.gif)
![Clap](https://passionford.com/forum/images/smilies/9c-clap.gif)
Mark
#39
![Default](https://passionford.com/forum/images/icons/icon1.gif)
not a dig or anything but why wasnt trick rods used so the revs can rise to high 8000 looking at that surly would see well over 600 bhp on pump fuel if the revs where to climb and more boost
well done carnt wait to get mine strapped on the dyno so see what it will put out wont be long now
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
![Banana](https://passionford.com/forum/images/smilies/banana_dance.gif)
well done carnt wait to get mine strapped on the dyno so see what it will put out wont be long now
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)