Breaking ex-time attack escort cosworth V8 800BHP.some price changes
#1
Part of the Furniture
Thread Starter
Breaking ex-time attack escort cosworth V8 800BHP.some price changes
All pictures can be found in this thread of parts for sale ---
https://passionford.com/forum/restor...3-05-11-a.html
Hi all with regret i am breaking my project so here is the list ,
MOTOR SPORT ESCORT COSWORTH SHELL SEAM WELDED CUSTOM CAGES FULL WELD IN CAGE CDS TYPE,WITH SEAT BARS,REAR BEAM MTS THROUGH BODY TO CAGE,GUSSETS FITTED ON DOOR BARS,ALL FITTED BY THEM COST £2800.WITH CERT.
COMES WITH DOORS,TAILGATE,BONNET WITH VENTS,REAR BUMPER,SIDE SKIRTS,ROOF VENT,TAIL LIGHTS,MIRRORS,
DOOR HANDLES +LOCKS,DOOR+TAILGATE SEALS,REAR QUARTER GLASS SEALS,SCUTTLE TRIM
BONNET PINS,DASH LESS CLOCKS,SHELL HAS REAR MTS FOR A BLADED ANTI ROLL BAR,
BRACKETS FOR FRONT COMPRESSION STRUTS,ALL GLASS EXCEPT FRONT SCREEN,
THE BULKHEAD HAS BEEN ALTERED TO TAKE MUSTANG V8 ENGINE, BUT I HAVE A BULKHEAD TO BE INCLUDED WITH
THE SHELL SO YOU CAN CONVERT BACK
IS REGISTERED AS RS2000 ON LOG BOOK, REG NUMBER K555 BHP.
SHELL NOW SOLD
HAVE ALL BITS TO GO WITH SHELL AT THE MOMENT.ALSO HAVE GENUINE FRONT BUMPER WITH INNER BRACE AND GRILL.
ANY MORE INFO JUST ASK.
SUPERCHARGED MUSTANG V8 ENGINE NEW NEVER RUN WITH GEARBOX,TILTON HYDRAULIC CLUTCH CONVERSION,HEAVY DUTY PROP SHAFT AND ECU,
FORGED AND STROKED TO 5.0 LTR,NEW HEADS ,CAMS,BLOCK ,CRANK ,RODS,PISTONS,ALL BALANCED,ALLOY FLY WHEEL, 1000BHP CLUTCH,FRONT COVERS, CAM COVERS ,COIL PACKS ARP STUDS LOWER +HEAD,WATER PUMP,OIL PUMP TIMING CHAINS+TENSIONERS,BILLET FUEL RAILS LARGE INJECTORS LARGE THROTTLE BODY DOUBLE THE FLOW VERY HIGH SPEC,WITH NEW STARTER,ALT ALL AUX BELTS ENGINE LOOM,INLET MANIFOLD CHARGE COOLER,SUPERCHARGER,ADJUSTABLE BOOST PULLEYS TO PICK THE BOOST YOU WANT ALL NEW SENSORS,WITH OMEX 710 STAND ALONE ECU BASE MAP SET BY OMEX THEMSELVES,OMEX MODIFIED IT TO RUN THIS ENGINE FOR ME COMES WITH EXTERNAL DRIVER'S 3 BAR MAP SENSOR AIR TEMP SENSOR WIRING CONNECTORS,OMEX HARNESS ,2"TIGHT FIT MANIFOLDS WRAPPED IN TITANIUM HEAT WRAP 4 INTO 1 TYPE,
FEW OTHER BIT TO GO WITH IT AS WELL,
WOULD NEED TO TALK YOU THROUGH IT ALL .. 600 BHP AT PRESENT TUNE WILL TAKE 850 BHP
ENGINE NOW SOLD
GORDON SPOONER REAR ROSE JOINTED BEAM WITH ARMS £700
CONCENTRIC STRUT TOPS SOLD
COMPRESSION STRUTS BUT NO MTG BRACKETS TO BODY HEAVY DUTY TYPE SOLD
AP 4 POT BRAKES 315mm DISCS WITH BELLS AND NEW PADS + MOUNTING BRKT'S £625
WHALE TAIL WITH LOWER SPOILER IN FRESH PAINT £170
INNER TAILGATE TRIM £15 NEW
REAR SCREEN TRIM GEN FORD £25 NEW
PRO ALLOY MIRROR IMAGE HEADER TANK STEALTH BLACK SOLD
PRO ALLOY HEADER TANK WITH 2 19MM OUTLETS ON FRONT STEALTH BLACK SOLD
ADJUSTABLE COOLING FAN SWITCH REPLACES STD SWITCH £25 NEW
FRONT GRILL AND SURROUND IN FRESH PAINT £65 NEW
MORRETS VERY GOOD CONDITION IN RED £165
PAIR FRONT STD HUB'S WITH OUTER CV JOINT SHAFT AND FLANGES SOLD
PAIR NEW REAR LAMP BULB HOLDER'S £35 NEW
FRONT SCUTTLE TRIM £10
NEW CLEAR FRONT INDICATORS AFTER MARKET £15 new
PAIR 909 SHOCKS WITH ROSE JOINTED MTG'S AND SPRINGS £225 SOLD
LIFELINE QUICK RELEASE WHEEL BOSS £170 @ DEMON TWEAKS £85 NEW
GAZ GOLD 65MM INNER SPRING DIAMETER 650lb 8" LONG SPRINGS PAIR £35 EACH @ GAZ £25 new
NYLON INNER TCA BUSHES £10 NEW
HAVE REMOVED SOLD ITEMS THAT HAVE BEEN POSTED OR COLLECTED
ANY QUESTIONS CALL ME THANKS ........TIM.
07989871057
Just to quickly add I havent time to sit at the PC all day to answer PM's so if you are genuinly interested please call for a chat.
I will be advertising these on other forums and will update thread daily as to what is sold.
Many thanks Tim.
https://passionford.com/forum/restor...3-05-11-a.html
Hi all with regret i am breaking my project so here is the list ,
MOTOR SPORT ESCORT COSWORTH SHELL SEAM WELDED CUSTOM CAGES FULL WELD IN CAGE CDS TYPE,WITH SEAT BARS,REAR BEAM MTS THROUGH BODY TO CAGE,GUSSETS FITTED ON DOOR BARS,ALL FITTED BY THEM COST £2800.WITH CERT.
COMES WITH DOORS,TAILGATE,BONNET WITH VENTS,REAR BUMPER,SIDE SKIRTS,ROOF VENT,TAIL LIGHTS,MIRRORS,
DOOR HANDLES +LOCKS,DOOR+TAILGATE SEALS,REAR QUARTER GLASS SEALS,SCUTTLE TRIM
BONNET PINS,DASH LESS CLOCKS,SHELL HAS REAR MTS FOR A BLADED ANTI ROLL BAR,
BRACKETS FOR FRONT COMPRESSION STRUTS,ALL GLASS EXCEPT FRONT SCREEN,
THE BULKHEAD HAS BEEN ALTERED TO TAKE MUSTANG V8 ENGINE, BUT I HAVE A BULKHEAD TO BE INCLUDED WITH
THE SHELL SO YOU CAN CONVERT BACK
IS REGISTERED AS RS2000 ON LOG BOOK, REG NUMBER K555 BHP.
SHELL NOW SOLD
HAVE ALL BITS TO GO WITH SHELL AT THE MOMENT.ALSO HAVE GENUINE FRONT BUMPER WITH INNER BRACE AND GRILL.
ANY MORE INFO JUST ASK.
SUPERCHARGED MUSTANG V8 ENGINE NEW NEVER RUN WITH GEARBOX,TILTON HYDRAULIC CLUTCH CONVERSION,HEAVY DUTY PROP SHAFT AND ECU,
FORGED AND STROKED TO 5.0 LTR,NEW HEADS ,CAMS,BLOCK ,CRANK ,RODS,PISTONS,ALL BALANCED,ALLOY FLY WHEEL, 1000BHP CLUTCH,FRONT COVERS, CAM COVERS ,COIL PACKS ARP STUDS LOWER +HEAD,WATER PUMP,OIL PUMP TIMING CHAINS+TENSIONERS,BILLET FUEL RAILS LARGE INJECTORS LARGE THROTTLE BODY DOUBLE THE FLOW VERY HIGH SPEC,WITH NEW STARTER,ALT ALL AUX BELTS ENGINE LOOM,INLET MANIFOLD CHARGE COOLER,SUPERCHARGER,ADJUSTABLE BOOST PULLEYS TO PICK THE BOOST YOU WANT ALL NEW SENSORS,WITH OMEX 710 STAND ALONE ECU BASE MAP SET BY OMEX THEMSELVES,OMEX MODIFIED IT TO RUN THIS ENGINE FOR ME COMES WITH EXTERNAL DRIVER'S 3 BAR MAP SENSOR AIR TEMP SENSOR WIRING CONNECTORS,OMEX HARNESS ,2"TIGHT FIT MANIFOLDS WRAPPED IN TITANIUM HEAT WRAP 4 INTO 1 TYPE,
FEW OTHER BIT TO GO WITH IT AS WELL,
WOULD NEED TO TALK YOU THROUGH IT ALL .. 600 BHP AT PRESENT TUNE WILL TAKE 850 BHP
ENGINE NOW SOLD
GORDON SPOONER REAR ROSE JOINTED BEAM WITH ARMS £700
CONCENTRIC STRUT TOPS SOLD
COMPRESSION STRUTS BUT NO MTG BRACKETS TO BODY HEAVY DUTY TYPE SOLD
AP 4 POT BRAKES 315mm DISCS WITH BELLS AND NEW PADS + MOUNTING BRKT'S £625
WHALE TAIL WITH LOWER SPOILER IN FRESH PAINT £170
INNER TAILGATE TRIM £15 NEW
REAR SCREEN TRIM GEN FORD £25 NEW
PRO ALLOY MIRROR IMAGE HEADER TANK STEALTH BLACK SOLD
PRO ALLOY HEADER TANK WITH 2 19MM OUTLETS ON FRONT STEALTH BLACK SOLD
ADJUSTABLE COOLING FAN SWITCH REPLACES STD SWITCH £25 NEW
FRONT GRILL AND SURROUND IN FRESH PAINT £65 NEW
MORRETS VERY GOOD CONDITION IN RED £165
PAIR FRONT STD HUB'S WITH OUTER CV JOINT SHAFT AND FLANGES SOLD
PAIR NEW REAR LAMP BULB HOLDER'S £35 NEW
FRONT SCUTTLE TRIM £10
NEW CLEAR FRONT INDICATORS AFTER MARKET £15 new
PAIR 909 SHOCKS WITH ROSE JOINTED MTG'S AND SPRINGS £225 SOLD
LIFELINE QUICK RELEASE WHEEL BOSS £170 @ DEMON TWEAKS £85 NEW
GAZ GOLD 65MM INNER SPRING DIAMETER 650lb 8" LONG SPRINGS PAIR £35 EACH @ GAZ £25 new
NYLON INNER TCA BUSHES £10 NEW
HAVE REMOVED SOLD ITEMS THAT HAVE BEEN POSTED OR COLLECTED
ANY QUESTIONS CALL ME THANKS ........TIM.
07989871057
Just to quickly add I havent time to sit at the PC all day to answer PM's so if you are genuinly interested please call for a chat.
I will be advertising these on other forums and will update thread daily as to what is sold.
Many thanks Tim.
Last edited by timbhp; 09-10-2011 at 08:08 PM. Reason: removed sold parts that have been collected or posted
#3
Lucifer II - 666
As said in the add mate, call or text him.
I wrote and placed the add earlier so this is sound advise lol
I wrote and placed the add earlier so this is sound advise lol
#5
Lucifer II - 666
In the thread linked in the 1st post bud.
Trending Topics
#9
I've found that life I needed.. It's HERE!!
iTrader: (6)
Join Date: Nov 2008
Location: Sussex
Posts: 1,341
Likes: 0
Received 0 Likes
on
0 Posts
Im interested in the tilton pedal box , cylinders and the bracketry that Tims made up for it al , im away all weekend but can call next week if its still there .
#11
Part of the Furniture
Thread Starter
#18
Part of the Furniture
Thread Starter
#21
Part of the Furniture
Thread Starter
#22
Part of the Furniture
Thread Starter
would you be collecting ?
thanks tim
Last edited by timbhp; 13-08-2011 at 09:29 PM.
#25
Part of the Furniture
Thread Starter
H 220mm not including filler neck
W 805mm includes mounting tray
D 420mm includes mounting tray
im not sure on the distance from you im just of junction 1 M42
thanks tim
Last edited by timbhp; 14-08-2011 at 08:47 AM.
#26
Part of the Furniture
Thread Starter
Hi mark, battery is not used,has been put on a battery optimate conditioner regularly kept in house ,
H 195mm or 206mm inc posts
D 95mm
W 250mm
thanks tim
#29
Part of the Furniture
Thread Starter
the shafts are larger dia
flanges have group a studs
hubs have larger wheel bearings in
all in good condition were fitted to a gordon spooner rear adjustable beam
hope this helps
thanks tim
Last edited by timbhp; 14-08-2011 at 01:17 PM.
#30
Part of the Furniture
Thread Starter
#32
Part of the Furniture
Thread Starter
#33
Advanced PassionFord User
iTrader: (1)
Thanks Tim,
I will have a think on those parts mate, i was looking for 1 grpa front flange as one of mine has been machined too much, but i could use 2wd flanges with sleeves, trying to decide, i presume your flanges are 2wd items originally? with possibly sleeves fitted to suit big bearings and modded for grpa studs.
I will have a think on those parts mate, i was looking for 1 grpa front flange as one of mine has been machined too much, but i could use 2wd flanges with sleeves, trying to decide, i presume your flanges are 2wd items originally? with possibly sleeves fitted to suit big bearings and modded for grpa studs.
#36
Part of the Furniture
Thread Starter
#37
Part of the Furniture
Thread Starter