pic of my camz
04-12-2005, 10:30 PM
#1
Too many posts.. I need a life!!
Thread Starter
Join Date: Sep 2005
Location: paignton
Posts: 585
Likes: 0
Received 0 Likes
on
0 Posts
pic of my camz
the one on the right is the new one can u see how battered the old one on the left is but it looks different is the left one a performance cam ?
massive chips and dents well bad i fink
massive chips and dents well bad i fink
04-12-2005, 11:59 PM
#2
10K+ Poster!!
Join Date: May 2005
Location: Cheltenham, Gloucestershire
Posts: 13,798
Likes: 0
Received 0 Likes
on
0 Posts
hello again mate 
welcome to the glorius world of CVH top ends
Fact of life with these, cam wear is inevitable.
Surprised to see an ultra parts cam
Everyone i mention that name to says "who are ultraparts" and screws up theyre face as if to say bet that wont last 5 minutes. 
How much did that set u back? Please say u bought new lifters aswell
Look at the dizzy end of your old cam and see what code is stamped in the end....?
welcome to the glorius world of CVH top ends
Fact of life with these, cam wear is inevitable.
Surprised to see an ultra parts cam
Everyone i mention that name to says "who are ultraparts" and screws up theyre face as if to say bet that wont last 5 minutes. How much did that set u back? Please say u bought new lifters aswell
Look at the dizzy end of your old cam and see what code is stamped in the end....?
05-12-2005, 06:24 AM
#4
Too many posts.. I need a life!!
Thread Starter
Join Date: Sep 2005
Location: paignton
Posts: 585
Likes: 0
Received 0 Likes
on
0 Posts
yeah got a kit with all new bits lifters etc lol the whole lot was under 100squid which i thought wasnt to bad
im hopeing it will last more then 5 mins haha
when i was taking thecam out and tappets to of the tappets were in two peices and fell apart as i undid the bolt that holds them down 2 of the bolts were a nitmare and were so tight that the tappet didnt have any movement ???
im hopeing it will last more then 5 mins haha
when i was taking thecam out and tappets to of the tappets were in two peices and fell apart as i undid the bolt that holds them down 2 of the bolts were a nitmare and were so tight that the tappet didnt have any movement ???
05-12-2005, 08:50 AM
#5
PassionFord Post Troll
iTrader: (2)
Join Date: Jan 2005
Location: Lincs
Posts: 3,269
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by JayRS2000
yeah got a kit with all new bits lifters etc lol the whole lot was under 100squid which i thought wasnt to bad
im hopeing it will last more then 5 mins haha
when i was taking thecam out and tappets to of the tappets were in two peices and fell apart as i undid the bolt that holds them down 2 of the bolts were a nitmare and were so tight that the tappet didnt have any movement ???
im hopeing it will last more then 5 mins haha
when i was taking thecam out and tappets to of the tappets were in two peices and fell apart as i undid the bolt that holds them down 2 of the bolts were a nitmare and were so tight that the tappet didnt have any movement ???
i can get a cam + followers for 65 off a mate
better than 300 odd for a piper etc
Thread
Thread Starter
Forum
Replies
Last Post
nicodinho
Ford Non RS / XR / ST parts for sale.
6
07-10-2015 12:56 PM
