PassionFord - Ford Focus, Escort & RS Forum Discussion
0 2022/07/02 13:00:45
0 2022/07/02 13:26:01
0 2022/07/02 13:27:19
Found some cross member pics of manual racks Sierra 2wd’s it does look like a pinch fitting.
Found some cross member pics of manual racks Sierra 2wd’s it does look like a pinch fitting.
0 2022/07/02 13:30:15
Maybe captive nut or threaded bottom on the cross member and top pinches it?
Maybe captive nut or threaded bottom on the cross member and top pinches it?
0 2022/07/02 13:30:17
I made up the L plate and welded that to the cage base, then welded that to the floor. I primed the insides first.
I made up the L plate and welded that to the cage base, then welded that to the floor. I primed the insides first.
0 2022/07/03 08:54:05
After the rust treatment cured I sanded it lightly to give a key and take off the high spots.
After the rust treatment cured I sanded it lightly to give a key and take off the high spots.
0 2022/07/03 08:56:09
Ready for seam sealer and then another coat of epoxy primer
Ready for seam sealer and then another coat of epoxy primer
0 2022/07/03 08:56:14
0 2022/07/03 08:56:20
0 2022/07/03 08:56:27
Cleaned up this part of the floor after stitch welding. Then I used a rust killer and sealant from bilt hamber
Cleaned up this part of the floor after stitch welding. Then I used a rust killer and sealant from bilt hamber
0 2022/07/03 08:56:33
I will sort out the red bit of the shell soon.
I will sort out the red bit of the shell soon.
0 2022/07/03 08:56:40
0 2022/07/03 08:56:46
Another problem ticked off the list.
Another problem ticked off the list.
0 2022/07/05 13:31:09
0 2022/07/06 00:34:52
The engine in these pics is too low, this is because I have the engine mounts the wrong way up. When I raise the engine it hits the scuttle panel / rain tray so I needed to make some room.
The engine in these pics is too low, this is because I have the engine mounts the wrong way up. When I raise the engine it hits the scuttle panel / rain tray so I needed to make some room.
0 2022/07/08 11:05:55
You can see where the cam position sensor and the breather will make contact.
You can see where the cam position sensor and the breather will make contact.
0 2022/07/08 11:06:01
So, the box sits under where I have marked in black for the width of the engine but the rail I have highlighted in yellow stays in place.
So, the box sits under where I have marked in black for the width of the engine but the rail I have highlighted in yellow stays in place.
0 2022/07/08 11:13:41
The tunnel cave. Old foot well meets new floor and tunnel.
The tunnel cave. Old foot well meets new floor and tunnel.
0 2022/07/09 05:29:39
0 2022/07/09 05:29:47
The cave
The cave
0 2022/07/09 05:29:52
0 2022/07/09 05:29:58
0 2022/07/09 05:30:04
Started to put the strength back in with 2 mm steel to link the floor to the sill.
Started to put the strength back in with 2 mm steel to link the floor to the sill.
0 2022/07/09 10:36:40
Bullet output flanges arrived from Anembo. These were one of the things that went missing from my car. Last MOT they mentioned slight play in front bearings which was odd as all brand new. By chance I was talking to Stuart Day who also had a set of the same “WRC” uprights, same issue. He sent his off to some F engineer and it seems the hubs may have a very slight oval in the machining. He had inserts cut in which sorted it. May have to do that. Anyone else had the same issue?
Bullet output flanges arrived from Anembo. These were one of the things that went missing from my car. Last MOT they mentioned slight play in front bearings which was odd as all brand new. By chance I was talking to Stuart Day who also had a set of the same “WRC” uprights, same issue. He sent his off to some F engineer and it seems the hubs may have a very slight oval in the machining. He had inserts cut in which sorted it. May have to do that. Anyone else had the same issue?
0 2022/07/20 01:35:28
Here is my Aprilia RS660.
Here is my Aprilia RS660.
0 2023/12/16 08:49:20
Tzr 250 engined mito, I went one pipe each side on custom tuned expansions. Most people double stack the pipes on one side.
Tzr 250 engined mito, I went one pipe each side on custom tuned expansions. Most people double stack the pipes on one side.
0 2023/12/16 08:49:27
The GSXR was bought new in 2012 by a 70yr old bloke, it had done 2000 miles and is as it left the factory, I really love this bike and the red line is around 14,000 rpm.
The GSXR was bought new in 2012 by a 70yr old bloke, it had done 2000 miles and is as it left the factory, I really love this bike and the red line is around 14,000 rpm.
0 2023/12/16 08:51:32