Rosso red Rs turbo build and progress.
The following users liked this post:
Rsmat (04-04-2018)
The following users liked this post:
Rsmat (29-03-2018)
The following users liked this post:
Rsmat (30-03-2018)
The following users liked this post:
turbo m (30-03-2018)
The following users liked this post:
Rsmat (30-03-2018)
01-04-2018, 10:06 AM
#573
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes
on
516 Posts
A few more bits arrived yesterday and came across another drama ..so a change in direction on the coil pack..im going to use a Fiesta Turbo coilpack.. just need to find a plug for it if anyone knows of someone with one or where I can purchase brand new..also the Head light decals turned up.
Here's the problem with polo coil pack and fiesta leads.
And this is the plug I need ..im going to buy a fiesta turbo coilpack and run that instead of the polo one .
Here's the problem with polo coil pack and fiesta leads.
And this is the plug I need ..im going to buy a fiesta turbo coilpack and run that instead of the polo one .
02-04-2018, 12:38 AM
#576
link doesnt seem to want to work
go to
http://www.polevolt.co.uk/index.html
go to connectors then vehicle specific connectors then it will be the first one
go to
http://www.polevolt.co.uk/index.html
go to connectors then vehicle specific connectors then it will be the first one
02-04-2018, 12:43 PM
#577
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes
on
516 Posts
link doesnt seem to want to work
go to
http://www.polevolt.co.uk/index.html
go to connectors then vehicle specific connectors then it will be the first one
go to
http://www.polevolt.co.uk/index.html
go to connectors then vehicle specific connectors then it will be the first one
Got it mate and ordered thanks very much
02-04-2018, 12:49 PM
#578
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes
on
516 Posts
A little update on the inlet ..still loads to do and finish off etc just a few progress shots .It should help increase the air velocity and distribute it more evenly. .massive thanks to Muz for his work and keeping me well informed along the way ..a real gent to work with .
02-04-2018, 12:51 PM
#579
10K+ Poster!!
That looks nicely made, very neat work. Who is Muz?
The following users liked this post:
Caddyshack (02-04-2018)
The following users liked this post:
Rsmat (02-04-2018)
02-04-2018, 08:23 PM
#584
PassionFord Post Troll
Manifold looks great matt, in one pic the turbo looked mega close to your brake servo but must of just been the angle it was taken at as it has good clearance.
03-04-2018, 02:55 PM
#589
PassionFord Post Troll
Looking good mate
The following users liked this post:
Rsmat (04-04-2018)
04-04-2018, 05:18 PM
#595
Boost addict
mate this is the update iv been waiting on 
what an engine bay and fantastic work from the guys who have done the manifolds.
when are you planning 1st start up? defo need a video or 2
what an engine bay and fantastic work from the guys who have done the manifolds. when are you planning 1st start up? defo need a video or 2
The following users liked this post:
Rsmat (04-04-2018)
04-04-2018, 07:56 PM
#596
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes
on
516 Posts
Got to wait on new inlet coming back and start some heat manangement so things behave well like the brakes etc then get the new simtek manangment fitted with my zeitronix monitor...than give it some boost.
The following users liked this post:
bluntys1rsturbo (05-04-2018)
05-04-2018, 07:18 AM
#597
Manifold looks great! Who built it again?
Cant wait to finally see this in the metal...when do you think it will be up and running? Whos doing the mapping work for you?
Cant wait to finally see this in the metal...when do you think it will be up and running? Whos doing the mapping work for you?
05-04-2018, 08:36 AM
#598
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,259
Received 583 Likes
on
516 Posts
Nikki at ND performance and fabrication built the manifold and down pipe etc .
I'm not tempting fate on a time so maybe 5 weeks ish nice and steady .
It's off to Zi motorsport for new uprated engine loom and Simtek manangement fitted and mapped to around 240 ish then ill head up to MSD and have a play on the dyno with Stu till I'm happy how it drives ..set up around 300hp .
