2002 Focus ST170
#41
PassionFord Regular
Thread Starter
Fitted my magnum grey fascia and gear surround. Hard to get a good picture with the light shining through the screen. Also fitted a harness with stalk controls so I can use the steering wheel controls.
#42
PassionFord Regular
Thread Starter
Just ordered a new radiator cross over pipe as it's sprung a leak. Also ordered new top and bottom silicone radiator hoses at the same time.
#43
Advanced PassionFord User
That looks pretty smooth inside
The following users liked this post:
JC600 (16-06-2016)
#47
PassionFord Regular
Thread Starter
They were the only ones too.
The following users liked this post:
STeve (18-06-2016)
#50
Advanced PassionFord User
It is the little changes that make the difference, and your car is looking good well done.
The following users liked this post:
JC600 (18-06-2016)
#53
PassionFord Regular
Thread Starter
Since I brought the car, its had a broken mirror that vibrates and wobbles about, as the clips in side broken. I found one on Ebay and won it for Ł1.04 lol
Before
After*
Happy days
Before
After*
Happy days
#54
Looks great, I've just got an ST170 and wanted one either in Imp Blue or Grey - settled on blue but the grey's do look great what did you do to refurb the gear knob? Mine could use that too!
The following users liked this post:
JC600 (24-06-2016)
#55
PassionFord Regular
Thread Starter
Just wet & dry with AutoSol metal polish. Takes a while though.
#57
PassionFord Regular
Thread Starter
Re-done my gear knob as I didn't like the red, so done it in dark grey. Looks loads better.
Also repaired scuffs, and re lacquered the mirror from the new mirror as it's a better fit. Plus then I'll have a spare one lol.
Also repaired scuffs, and re lacquered the mirror from the new mirror as it's a better fit. Plus then I'll have a spare one lol.
#58
That looks awesome, I think I'll be doing the same this weekend!
The following users liked this post:
JC600 (24-06-2016)
#60
PassionFord Regular
Thread Starter
#61
Goddamn, do you take gearknob refurb requests? That looks amazing!
#62
PassionFord Regular
Thread Starter
#67
PassionFord Regular
Thread Starter
Yesterday the ST started jerking at 3000-3500 rpm.....this morning my neighbour started the car so I could see if the cable on the imrc moved. When I noticed it wasn't attached.....so Re-fitted it, took for a drive and it was spot on. Also popped into my brothers work and plugged it into the snap on diagnosis machine. Only codes were P1518 & P1519, cleared these test drive and re-tested. No codes found.
#68
PassionFord Regular
Thread Starter
Ordered some Genuine Ford mats today, also found some 12v blanks for the 2 12v sockets.
Then a good wash and wax. Love the magnum grey after a wax.
Then a good wash and wax. Love the magnum grey after a wax.
The following users liked this post:
JC600 (01-07-2016)
The following users liked this post:
JC600 (02-07-2016)
#73
PassionFord Regular
Thread Starter
#76
PassionFord Regular
Thread Starter
Put a jubilee clip on the throttle body hose, as it was missing.......and the car is booked for smart repair at the end of the month. front bumper is being painted and repaired, all the previous touch up paint is getting cleaned up and blended in. Rust under wing mirror is being treated and then painted. Any other chips or scratches are being touched in. Then the whole car will be mopped.*
Decided to go down this route, as didn't want the cost of different panels being fully painted and blended in. Then someone open a door into it, in a car park or something......Just want it clean and tidy.
Only down side is I can't polish it till its done now lol*
Decided to go down this route, as didn't want the cost of different panels being fully painted and blended in. Then someone open a door into it, in a car park or something......Just want it clean and tidy.
Only down side is I can't polish it till its done now lol*
#77
Advanced PassionFord User
All sounds really good a very nice ST170
The following users liked this post:
JC600 (05-07-2016)
#79
Regular Contributor
Car looks good.