Fiesta RS Turbo Project
#522
10K+ Poster!!
iTrader: (1)
Originally Posted by 1900cvh
Originally Posted by BillyCabrio
Originally Posted by rich_frst
where'd you get your braided lines matey?!?!?!
looking good mate... how much longer till its finished!?!
looking good mate... how much longer till its finished!?!
Did they come with all the male and female fittings too?
Hopefully it will all be done for fordfair !!!
#523
Advanced PassionFord User
Join Date: May 2003
Location: Manchester
Posts: 1,622
Likes: 0
Received 0 Likes
on
0 Posts
#524
I've found that life I needed.. It's HERE!!
Thread Starter
Join Date: Aug 2004
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BillyCabrio
Originally Posted by 1900cvh
Originally Posted by BillyCabrio
Originally Posted by rich_frst
where'd you get your braided lines matey?!?!?!
looking good mate... how much longer till its finished!?!
looking good mate... how much longer till its finished!?!
Did they come with all the male and female fittings too?
Hopefully it will all be done for fordfair !!!
I paid around Ł250 - Ł280 !!!
#525
I've found that life I needed.. It's HERE!!
Thread Starter
Join Date: Aug 2004
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by RS_Rawli
#526
I've found that life I needed.. It's HERE!!
Thread Starter
Join Date: Aug 2004
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
Lower arms with the bushes in them !!!
Top linkage is all sorted !!!
Alternator belt !!!
Throttle cable !!!
Thottle body all stripped !!!
All these bit's r going off to be Zinc pas !!!
Also went to fords again !!!
Sump gasket !!!
Top linkage is all sorted !!!
Alternator belt !!!
Throttle cable !!!
Thottle body all stripped !!!
All these bit's r going off to be Zinc pas !!!
Also went to fords again !!!
Sump gasket !!!
#529
Advanced PassionFord User
Join Date: May 2003
Location: Manchester
Posts: 1,622
Likes: 0
Received 0 Likes
on
0 Posts
#531
I've found that life I needed.. It's HERE!!
Join Date: Dec 2004
Location: canvey island
Posts: 1,379
Likes: 0
Received 0 Likes
on
0 Posts
1900cvh,
Alright dude hows it hangin? cheers for sortin us out with tose multi plugs!! can get on with the loom now! ill pm me mate the painters no!!!
Alright dude hows it hangin? cheers for sortin us out with tose multi plugs!! can get on with the loom now! ill pm me mate the painters no!!!
#534
I've found that life I needed.. It's HERE!!
Thread Starter
Join Date: Aug 2004
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Davey8oy
1900cvh,
Alright dude hows it hangin? cheers for sortin us out with tose multi plugs!! can get on with the loom now! ill pm me mate the painters no!!!
Alright dude hows it hangin? cheers for sortin us out with tose multi plugs!! can get on with the loom now! ill pm me mate the painters no!!!
#537
I've found that life I needed.. It's HERE!!
Thread Starter
Join Date: Aug 2004
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
Look wot i got today !!!
A new TPS sensor !!!
Also went to fords too !!!
A new start moter loom !!!
Wiper arm's !!!
Bit's & bob's !!!
Bottom pulley all done !!!
K & N Crank case filter !!!
Rear caliper brkts !!!
A new TPS sensor !!!
Also went to fords too !!!
A new start moter loom !!!
Wiper arm's !!!
Bit's & bob's !!!
Bottom pulley all done !!!
K & N Crank case filter !!!
Rear caliper brkts !!!
#539
I've found that life I needed.. It's HERE!!
Join Date: Nov 2004
Location: ESSEX canvey island
Posts: 1,446
Likes: 0
Received 0 Likes
on
0 Posts
CHICKEN, that pic of the pully is a zeta 1 . u need 2 work out where the sensor is goin 2 be. then work out the pick up points. 90 degrees 2 each other on the cvh pully.
#544
I've found that life I needed.. It's HERE!!
Thread Starter
Join Date: Aug 2004
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
TUT TUT TUT rich p xr2t, i thought u knew your bottom pulleys Alot better mate !!!!!!
CHICKEN,
It is a 1800CVH pulley with the other lugs machined off & just 4 left at 90o to each other mate !!!!!
A mate at work did it for me !!!!!!!!!!!
CHICKEN,
It is a 1800CVH pulley with the other lugs machined off & just 4 left at 90o to each other mate !!!!!
A mate at work did it for me !!!!!!!!!!!
#545
I've found that life I needed.. It's HERE!!
Thread Starter
Join Date: Aug 2004
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 1992FRST
ive been keeping an eye on this car for a while now, cant wait to to see the finished article :
#546
I've found that life I needed.. It's HERE!!
Thread Starter
Join Date: Aug 2004
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by N1C4T3N
loads of new parts got any like hole pics of the car how it is at the mo?
#547
I've found that life I needed.. It's HERE!!
Join Date: Dec 2004
Location: canvey island
Posts: 1,379
Likes: 0
Received 0 Likes
on
0 Posts
1900cvh,
Alright dude hows the car runnin now????? many thanks for the extra pair of hands doin me car!!
rich p xr2t,
its a zetec i think??????? JACKASS!!!!!!!!!!!!!!!!!!lol
Alright dude hows the car runnin now????? many thanks for the extra pair of hands doin me car!!
rich p xr2t,
its a zetec i think??????? JACKASS!!!!!!!!!!!!!!!!!!lol
#548
I've found that life I needed.. It's HERE!!
Thread Starter
Join Date: Aug 2004
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Davey8oy
1900cvh,
Alright dude hows the car runnin now????? many thanks for the extra pair of hands doin me car!!
rich p xr2t,
its a zetec i think??????? JACKASS!!!!!!!!!!!!!!!!!!lol
Alright dude hows the car runnin now????? many thanks for the extra pair of hands doin me car!!
rich p xr2t,
its a zetec i think??????? JACKASS!!!!!!!!!!!!!!!!!!lol
Any time !!!!
#554
I've found that life I needed.. It's HERE!!
Thread Starter
Join Date: Aug 2004
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by jabba
The dedication and expense you're putting into this is unreal, well done.
And keep them updates coming.
And keep them updates coming.
#555
I've found that life I needed.. It's HERE!!
Thread Starter
Join Date: Aug 2004
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
Started to slowly build up the rear end !!!!
Rear beam with the bushes & mount !!!
My rear hubs !!!
Rear bearing kits !!!
Also got a new handbrake cable !!!
Rear beam with the bushes & mount !!!
My rear hubs !!!
Rear bearing kits !!!
Also got a new handbrake cable !!!