3dr cosworth built... Update collected 6degree beam **
#1081
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,262
Received 585 Likes
on
517 Posts
Well had another play tonight and made another bulkhead matt... Just wants hole punching .. I will send it to Steve for him to try this week here's a few pics .hope ya like .
#1083
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,262
Received 585 Likes
on
517 Posts
Wheels where on there way but .. They got the order wrong so there being anodised gold instead of polished centres so a slight delay there ... And I've sent my sump for big winging and baffled
#1087
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,262
Received 585 Likes
on
517 Posts
Well not much of a update .. But here's what I've got and what's in progress etc
Big wing and baffled sump .. As been sent off to be done.
Wheels ...I'm still waiting for .. Should be long now .
Sending some plastics for flocking for my rear strut brace set up
Rear 300mm and 4x4 callipers ... Sorted
I've bought a brand new gear knob and gaiter.... Brand new pedal rubbers
Brand new door seals and boot seal
Can't think of anything else I'm due a part from im after a 3dr rear beam and arms so I can send it off for 6degeee and then buy a diff to suit
Big wing and baffled sump .. As been sent off to be done.
Wheels ...I'm still waiting for .. Should be long now .
Sending some plastics for flocking for my rear strut brace set up
Rear 300mm and 4x4 callipers ... Sorted
I've bought a brand new gear knob and gaiter.... Brand new pedal rubbers
Brand new door seals and boot seal
Can't think of anything else I'm due a part from im after a 3dr rear beam and arms so I can send it off for 6degeee and then buy a diff to suit
#1088
10K+ Poster!!
Sounds good!
#1091
Zee Germans are coming
Mat I think with the way you have gone at the rest of the car it would be a massive shame not to go balls deep on the engine bay
Or are you already doing it and I've missed something
Or are you already doing it and I've missed something
#1093
Zee Germans are coming
#1097
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,262
Received 585 Likes
on
517 Posts
Slight delay with them... They was getting sent had the call for confirmation of delivery address and in convo they told me they was polished so I said hopefully not all the rim and they said yes .. I said my order was gold centre polished outers ... So still sat waiting ..
#1101
Advanced PassionFord User
Looking amazing Mat. Who does your powder coating? The gut I use cant get a finish close to that of yours.
#1102
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,262
Received 585 Likes
on
517 Posts
Nothing at the minute mate... I'm collecting stuff for the build
My friend owns a powder coaters mate here in Sheffield... His work is top notch.. He always tells me the key to good coating is the prep work
Here's the tanks he did me there like glass
#1105
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,262
Received 585 Likes
on
517 Posts
3dr beam acquired form MT Motorsport ... Many thanks mate ...
Since seeing Ronnie's car run at time attack .. I've gone down the same route and I'm having the same beam from MK Motorsport .. I've been down this morning and dropped it off .. Very nice chap .. Many thank mate
Since seeing Ronnie's car run at time attack .. I've gone down the same route and I'm having the same beam from MK Motorsport .. I've been down this morning and dropped it off .. Very nice chap .. Many thank mate
#1106
I've found that life I needed.. It's HERE!!
iTrader: (1)
3dr beam acquired form MT Motorsport ... Many thanks mate ...
Since seeing Ronnie's car run at time attack .. I've gone down the same route and I'm having the same beam from MK Motorsport .. I've been down this morning and dropped it off .. Very nice chap .. Many thank mate
Since seeing Ronnie's car run at time attack .. I've gone down the same route and I'm having the same beam from MK Motorsport .. I've been down this morning and dropped it off .. Very nice chap .. Many thank mate
good to meet you and thanks for going for my beam ,in person you were different to what i expected lol
mark
#1109
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,262
Received 585 Likes
on
517 Posts
That's the military in me ... I swear like I trooper so apologies there in advance for next time aswell ..
Ps then big angry maulers can't move as fast as my hands and feet lol
#1114
PassionFord Post Whore!!
hahaha
#1115
300+
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: either at work or on way :)
Posts: 27,262
Received 585 Likes
on
517 Posts
Think I'm going to use this style clip first on the centre locks ... Got another two styles one Jimbo Gibbs is ruining on his which I supplied .. And one same as they use on the TSW HOCKS .
#1118
Under the car...!
Looking very nice! can you send me your powder coaters number mate. Looks better than the stuff I have had done!
As for the alloys - beautiful!! Just so happens Ive got the same ones lol so Im biased.
http://i17.photobucket.com/albums/b7...ps6f5dd0ab.jpg
As for the alloys - beautiful!! Just so happens Ive got the same ones lol so Im biased.
http://i17.photobucket.com/albums/b7...ps6f5dd0ab.jpg