focus rwd now for sale
#602
rite as iv not had much intrest im going to finish the body work ,striped it down after
work, repair drivers door (slite dent) an primer both doors and finish wing plus bumpers so they ready for paint
already primerd the boot lid
start a door aftertea
work, repair drivers door (slite dent) an primer both doors and finish wing plus bumpers so they ready for paint
already primerd the boot lid
start a door aftertea
Last edited by dingla rs; 24-06-2010 at 10:28 PM.
#610
as its not shifted yet i fort id finish the primer and prep work wount be flating it tho.
just door and front bumper to do now
and beefy coming throw with block an that to fit for some pic's t mro all been well
only primed whats needed
didnt really need the bottom half doing again but easier to do hole side than spot prime stone chips ect
just door and front bumper to do now
and beefy coming throw with block an that to fit for some pic's t mro all been well
only primed whats needed
didnt really need the bottom half doing again but easier to do hole side than spot prime stone chips ect
#613
PassionFord Post Troll
LOL not quite in yet .... Had a nice update from Alex today saying all the front end work had been completed and hes making good headway with the fuel tank and filler. Im gonna try and get over to ProAlloy tomorrow to get some more pictures.
#614
picked a block up to nite outa 2lt sierra gave me pistons and crank and cor plugs
dont knw if i can use crank not got much clue when it comes to engine's
beefy very kindly left his engine an bits at weekend for me mock up for pics but as
i was panicking as his block painted an didint want to mark it will get it mocked up to 2mrrow at some point
dont knw if i can use crank not got much clue when it comes to engine's
beefy very kindly left his engine an bits at weekend for me mock up for pics but as
i was panicking as his block painted an didint want to mark it will get it mocked up to 2mrrow at some point
#615
PassionFord Post Whore!!
iTrader: (3)
well done mate right down to it
205 block good to use
rods are going in the bin
pistons are going in the bin
crank is going in the bin
oil pump ok ..
but it needs a cosworth lid on it or you have the block moded for the oil spray to the pistons or get a 2wd cosworth oil pick up pipe
205 block good to use
rods are going in the bin
pistons are going in the bin
crank is going in the bin
oil pump ok ..
but it needs a cosworth lid on it or you have the block moded for the oil spray to the pistons or get a 2wd cosworth oil pick up pipe
#616
well done mate right down to it
205 block good to use
rods are going in the bin
pistons are going in the bin
crank is going in the bin
oil pump ok ..
but it needs a cosworth lid on it or you have the block moded for the oil spray to the pistons or get a 2wd cosworth oil pick up pipe
205 block good to use
rods are going in the bin
pistons are going in the bin
crank is going in the bin
oil pump ok ..
but it needs a cosworth lid on it or you have the block moded for the oil spray to the pistons or get a 2wd cosworth oil pick up pipe
rite so i need a different pipe for the pump then?
it was cheap an close just at leeds
#625
PassionFord Post Whore!!
iTrader: (2)
Sorry boys ive been really busy doing other things (mates car's and family)
i put my back out after going to castle coombe on sat and ive been lying on the settee for nearly two day's
Ive made a template for my boot floor now just gotta transfer that onto steel then practise with my m8s bead roller before i attack the floor, than when thats all done i can finish off the rear seat mount/floor
Will try and update my post soon if i can find it
i put my back out after going to castle coombe on sat and ive been lying on the settee for nearly two day's
Ive made a template for my boot floor now just gotta transfer that onto steel then practise with my m8s bead roller before i attack the floor, than when thats all done i can finish off the rear seat mount/floor
Will try and update my post soon if i can find it
#626
ffoc.co.uk
It's all coming together now, no time for standing around. Chop chop.
#629
rite iv been doing some work on the car finished matrix pipe work ,just needs a gasket
making for sealing bulkhead .i will be priming the area . waiting on a rad coming so i can drill tham holes aswell ,need it gone now as it holding work up
iv removed the lip on bulkhead not an issue just gives more room for bulkhead,and removed thrid wiper mount as it was pain get past if engine in one lump makes no odds to how it works
some one part with cash now £4200.00
its had the doors primerd wing ,front bumper bootlid ,back bumper is nw painted item
imperial blue that is
making for sealing bulkhead .i will be priming the area . waiting on a rad coming so i can drill tham holes aswell ,need it gone now as it holding work up
iv removed the lip on bulkhead not an issue just gives more room for bulkhead,and removed thrid wiper mount as it was pain get past if engine in one lump makes no odds to how it works
some one part with cash now £4200.00
its had the doors primerd wing ,front bumper bootlid ,back bumper is nw painted item
imperial blue that is
Last edited by dingla rs; 06-07-2010 at 05:18 PM.
#632
yer bit gutted me self i could bought a cheap 4x4 but it will be gone now mite be better with engine pics i hope as beefy the legend lent me his bits for the pics even left them with me ,but he knws the fav will be returned and i wount nick his bits
#633
BANNED
BANNED
Join Date: Jan 2005
Location: North Wales....Congleton now though!
Posts: 9,757
Likes: 0
Received 1 Like
on
1 Post
Sits in exactly the same position as mine mate, the right area far back in the bay. Spot on, shouldn't have issues with weight distribution, mine handles in a far superior way than a Focus RS