Big job for Stu and Kenny.............
#41
Regular Contributor
Thread Starter
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Thanks Stu...Im very pleased this happened whilst the car was with you, because if this had happened on the way back to Belgium......Well you can imagine what a nightmare that would have been....Any chance of some more oics of whats going on as Im so far away and of the tank, pump etc....and for a BIG lesson to all who dont store thier car with a full tank........Thanks Noel
![Clap](https://passionford.com/forum/images/smilies/9c-clap.gif)
#42
Regular Contributor
Thread Starter
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Spoke to Kenny this evening.......alls done except the live mapping, engineers report for the insurance is done so should be picking it up Fri morning......hopefully...still got the standard 4x4 clutch, so Kenny wont be giving it full BHP yet, I will change the clutch for an AP one.......so close now..except the BILL.
Its nearly been there a month, but it should be worth it..Just need to fit the rear parcel shelf, all the boot decals, stereo, and finally tweek the front bumper and rear arches, because the 18s are still catching a bit.....But Hey after all the work Al and Kenny have done so far.......Its done...
And thanks to you all for your support and interest in my little project ..Wilmot (Liege-Belgium)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Surprised](https://passionford.com/forum/images/smilies/bigcry.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
#48
Regular Contributor
Thread Starter
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Need to pick your brains......Just reading Fast Ford July 2004, about Nothampton Motorsport. Its all about suspension geometry, castor, camber etc etc...Well as some of you know I live just outside Liege-Belgium, and I have a 3 Door (4x4 350bhp)all sorted by Kenny at MSD.... its quite a treck across the Channel to Northhampton to get all my Suspension sorted.... Does anyone know of a similar type of company who knows what thier talking about to set my Car up PROPERLY..with the crossing im 3 1/2 hours from Dover, so Idealy South East....Please can somebody help.. Thanks to all.. Noel aka Wilmot........
![007](https://passionford.com/forum/images/smilies/bond.gif)
#51
10K+ Poster!!
iTrader: (1)
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Need to pick your brains......Just reading Fast Ford July 2004, about Nothampton Motorsport. Its all about suspension geometry, castor, camber etc etc...Well as some of you know I live just outside Liege-Belgium, and I have a 3 Door (4x4 350bhp)all sorted by Kenny at MSD.... its quite a treck across the Channel to Northhampton to get all my Suspension sorted.... Does anyone know of a similar type of company who knows what thier talking about to set my Car up PROPERLY..with the crossing im 3 1/2 hours from Dover, so Idealy South East....Please can somebody help.. Thanks to all.. Noel aka Wilmot........![007](https://passionford.com/forum/images/smilies/bond.gif)
![007](https://passionford.com/forum/images/smilies/bond.gif)
http://www.elitedirect.com/06a-alignment/index.html
I also know IIRC that Neil from Fast Ford has used them on one of his visits over this way.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
#52
Regular Contributor
Thread Starter
![Default](https://passionford.com/forum/images/icons/icon1.gif)
Will check out their website...............Got the same question in T&Q, and Tabetha mentoined somewhere in Holland......Does anyone know of anywherein Holland or Belgium.......Must be somewhere....This side.....
![007](https://passionford.com/forum/images/smilies/bond.gif)
#55
OCD Victim
![Default](https://passionford.com/forum/images/icons/icon1.gif)
I live in the South-East mate and theres only one place that really springs to mind that i've have used with success, their in Rainham, Essex - 10 mins from the Dartford Crossing on the M25...
http://www.elitedirect.com/06a-alignment/index.html
I also know IIRC that Neil from Fast Ford has used them on one of his visits over this way.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
http://www.elitedirect.com/06a-alignment/index.html
I also know IIRC that Neil from Fast Ford has used them on one of his visits over this way.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
Nowadays, I think it is all about the money and not so much the customer service quality, which is a damn shame.
#56
OCD Victim
![Default](https://passionford.com/forum/images/icons/icon1.gif)
I live in the South-East mate and theres only one place that really springs to mind that i've have used with success, their in Rainham, Essex - 10 mins from the Dartford Crossing on the M25...
http://www.elitedirect.com/06a-alignment/index.html
I also know IIRC that Neil from Fast Ford has used them on one of his visits over this way.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
http://www.elitedirect.com/06a-alignment/index.html
I also know IIRC that Neil from Fast Ford has used them on one of his visits over this way.
![Top](https://passionford.com/forum/images/smilies/smile011.gif)
Nowadays, I think it is all about the money and not so much the customer service quality, which is a damn shame.
Never had an issue except for the last 3 times I went there. Every one of those times I had to go back because of something that was not set right.
Got to admit though, their Hunter tracking machines are the industry-leaders inquality and accuracy.
Last edited by iansoutham; 12-05-2008 at 07:23 PM.
Thread
Thread Starter
Forum
Replies
Last Post
nicodinho
Ford Non RS / XR / ST parts for sale.
6
07-10-2015 12:56 PM
SMILER258
Restorations, Rebuilds & Projects.
36
28-09-2015 09:04 AM