Some new R&B Products....
#42
Originally Posted by CossieRich
Originally Posted by Bosch-Man
.....Mike did you get permission to sell these parts or have you gone back door your specialty?
#43
Did Someone Mention TUV
iTrader: (1)
Originally Posted by Bosch-Man
Originally Posted by CossieRich
Originally Posted by Bosch-Man
.....Mike did you get permission to sell these parts or have you gone back door your specialty?
#44
Originally Posted by CossieRich
Originally Posted by Bosch-Man
Originally Posted by CossieRich
Originally Posted by Bosch-Man
.....Mike did you get permission to sell these parts or have you gone back door your specialty?
He may want more of my butt knowing he was acceptable...infact no wonder he gets on so well as a bum bandit....he is nicknamed the doctor cause of his phrase..."dont worry you wont feel a thing its only a little prick"
#45
Originally Posted by RichardPON
Diff cover, oil/fuel pressure gauge take offs, lambda sensor boss, fuel rail, and actuator rods.....
......... but where the hell does that banjo arm thing go?
......... but where the hell does that banjo arm thing go?
#46
Advanced PassionFord User
iTrader: (5)
Originally Posted by RichardPON
Originally Posted by RichardPON
Diff cover, oil/fuel pressure gauge take offs, lambda sensor boss, fuel rail, and actuator rods.....
......... but where the hell does that banjo arm thing go?
......... but where the hell does that banjo arm thing go?
#48
Originally Posted by CossieRich
Originally Posted by Bosch-Man
Originally Posted by CossieRich
Originally Posted by Bosch-Man
.....Mike did you get permission to sell these parts or have you gone back door your specialty?
Mike has even got the T-shirt to prove it:
#52
Originally Posted by GARETH T
i like the diff plate how much mike i was going to make one myself over the winter
#54
Originally Posted by GARETH T
your so wrong there chip,,, im far from tight,,, tight people have lots of money
#55
Well if he makes it out of a cheap alloy block, he'll be in trouble - the material alone is nearly £60 to get the required "strength" . Obviously it's not for everyone, but also has the added benefit of increasing the oil capacity by a small amount as well .
I'll have prices for everything later today / tomorrow.
I'll have prices for everything later today / tomorrow.
#57
Originally Posted by GARETH T
i was going to make one from steel TBH
Added bonus then besides the extra strength/toughness/stiffeness is that if it ever scrapes the ground it will spark like a mofo
#58
Re: Some new R&B Products....
[quote="Mike Rainbird"]
are those aluminium?
High grade stainless-steel .
Hard to tell by the pic but is the Y-piece smaller than the OEM item or is it just the color that differ?
Originally Posted by martin-reyland
Originally Posted by Mike Rainbird
are those aluminium?
#60
Too many posts.. I need a life!!
Join Date: Mar 2005
Location: somewhere between bournemouth & southampton
Posts: 683
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Mike Rainbird
Well if he makes it out of a cheap alloy block, he'll be in trouble - the material alone is nearly £60 to get the required "strength" . Obviously it's not for everyone, but also has the added benefit of increasing the oil capacity by a small amount as well .
I'll have prices for everything later today / tomorrow.
I'll have prices for everything later today / tomorrow.
What is the spec of the Material ?
#61
Originally Posted by PaulCossie
Originally Posted by Mike Rainbird
Well if he makes it out of a cheap alloy block, he'll be in trouble - the material alone is nearly £60 to get the required "strength" . Obviously it's not for everyone, but also has the added benefit of increasing the oil capacity by a small amount as well .
I'll have prices for everything later today / tomorrow.
I'll have prices for everything later today / tomorrow.
What is the spec of the Material ?
#63
Too many posts.. I need a life!!
Join Date: Mar 2005
Location: somewhere between bournemouth & southampton
Posts: 683
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Mike Rainbird
Originally Posted by PaulCossie
Originally Posted by Mike Rainbird
Well if he makes it out of a cheap alloy block, he'll be in trouble - the material alone is nearly £60 to get the required "strength" . Obviously it's not for everyone, but also has the added benefit of increasing the oil capacity by a small amount as well .
I'll have prices for everything later today / tomorrow.
I'll have prices for everything later today / tomorrow.
What is the spec of the Material ?
#64
Originally Posted by cossie4i
Just a quick question about the shims for RWD Cossies Mike.
1. Do they help a lot with tyre wear and traction ?
2. How hard are they to fit and do you get fitting instructions ?
Thanks
Steve.
1. Do they help a lot with tyre wear and traction ?
2. How hard are they to fit and do you get fitting instructions ?
Thanks
Steve.
2. Providing everything is not siexed, should take no more than 30 minutes a side, and yes it does come with full instructions .
Prices now added to the items .
#65
TT T38 Power
iTrader: (15)
Originally Posted by Mike Rainbird
Originally Posted by cossie4i
Just a quick question about the shims for RWD Cossies Mike.
1. Do they help a lot with tyre wear and traction ?
2. How hard are they to fit and do you get fitting instructions ?
Thanks
Steve.
1. Do they help a lot with tyre wear and traction ?
2. How hard are they to fit and do you get fitting instructions ?
Thanks
Steve.
2. Providing everything is not siexed, should take no more than 30 minutes a side, and yes it does come with full instructions .
Prices now added to the items .
I will get my car in the 12s
Steve.
#66
PassionFord Post Whore!!
Join Date: Apr 2004
Location: oxfordshire/berkshire
Posts: 7,053
Likes: 0
Received 0 Likes
on
0 Posts
Re: Some new R&B Products....
[quote="seand"]
are those aluminium?
High grade stainless-steel .
thank fook for that, i could just imagine how many people would have snapped them off in the block whilst tightening them up
btw.. nice carpet, was it cheap?
Martin its a Carpet tile alot cheaper
Some bling looking bits mike i take it you did'nt say whot the bits are thats why you had lots of silly answers
Originally Posted by martin-reyland
Originally Posted by Mike Rainbird
Originally Posted by martin-reyland
Originally Posted by Mike Rainbird
are those aluminium?
btw.. nice carpet, was it cheap?
Some bling looking bits mike i take it you did'nt say whot the bits are thats why you had lots of silly answers
#67
PassionFord Post Whore!!
Join Date: Apr 2004
Location: oxfordshire/berkshire
Posts: 7,053
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Mike Rainbird
Originally Posted by Franco
The prices on your website yet Mike?
As to the "carpet" it is actually one of Sunlight's finest mats - the carpet underneath is FAR worse .