Saph Boa turbo conversion!!
#162
Today after 2 week ends of shit weather I managed to finish my garage roof so I can now start my conversion but 1st after advise from Ade500 I put engine on engine stand spun it upside down to whip sump off and check bearings and main bearings and chain all seems gd and bottom end looks new.
#166
Right Yesterday I ordered a zink set of driveshaft bolts and diff mounting bolts I also sourced a set of engine mounting bolts, today I started the process of bolting everything together in preparation to remove my lump and re fit my boa however I hit a stumbling block......
I bolted mounts too engine cradle and when I was about to mount to the engine arms guess what the arms are too long.....
I bolted mounts too engine cradle and when I was about to mount to the engine arms guess what the arms are too long.....
#169
i dont want to fuck your easter up anymore but, is that a 7.5" rear beam? 7 and 7.5 are different. as for the arms are you using the twin cam items? try the originals.
#175
i looked at vibratech but read somewhere on here that they lift the engine up too far on a 4i. i await yours being fitted and a definite answer. good luck with engine fitting.
#181
ELASTIC BAND
The blue plug, don't know, but not needed to run the engine. Think that splits from the engine loom quite easy
The black lump attached to the metal bit, egr sensor parts I think, needed to be plugged in , but ports blanked off.
Can't find the photo of my loom laid out,
Can sort something out and pop round tommorow if you want, would be 2 ish, if that's any good?
The black lump attached to the metal bit, egr sensor parts I think, needed to be plugged in , but ports blanked off.
Can't find the photo of my loom laid out,
Can sort something out and pop round tommorow if you want, would be 2 ish, if that's any good?
#182
The blue plug, don't know, but not needed to run the engine. Think that splits from the engine loom quite easy
The black lump attached to the metal bit, egr sensor parts I think, needed to be plugged in , but ports blanked off.
Can't find the photo of my loom laid out,
Can sort something out and pop round tommorow if you want, would be 2 ish, if that's any good?
The black lump attached to the metal bit, egr sensor parts I think, needed to be plugged in , but ports blanked off.
Can't find the photo of my loom laid out,
Can sort something out and pop round tommorow if you want, would be 2 ish, if that's any good?
#187
Anyone doing this conversion who is in need of a propshaft!
http://www.ebay.co.uk/itm/Ford-Sierr...item43b77d3b62
http://www.ebay.co.uk/itm/Ford-Sierr...item43b77d3b62
#194
Things are soon to be in full gear now my schedule is this weather dependant of coarse;
Friday evening disconnect/unplug and remove engine loom and ancillaries from saph fit new spigot bearing and sandwich plate then fit 2.8 flywheel, mount 6paddle ap racing clutch and bolt hybrid gearbox to engine.
Saturday remove engine/gearbox/prop/and all 4x4 running gear from saph then remove non abs servo/mc and refit an abs servo/mc then fit/mount BOA into engine bay and pipe up what I can.
Sunday fit 2wd front hubs/brakes/arb/tca's refit wheels, remove 7" rear beam/arms/diff/handbrake cable and refit new powder coated 7.5" rear beam/arms/diff handbrake cable, refit wheels.
Then it's a matter of waiting for my specially adapted abs loom to come back to be fitted and my boa to sierra engine loom.
Friday evening disconnect/unplug and remove engine loom and ancillaries from saph fit new spigot bearing and sandwich plate then fit 2.8 flywheel, mount 6paddle ap racing clutch and bolt hybrid gearbox to engine.
Saturday remove engine/gearbox/prop/and all 4x4 running gear from saph then remove non abs servo/mc and refit an abs servo/mc then fit/mount BOA into engine bay and pipe up what I can.
Sunday fit 2wd front hubs/brakes/arb/tca's refit wheels, remove 7" rear beam/arms/diff/handbrake cable and refit new powder coated 7.5" rear beam/arms/diff handbrake cable, refit wheels.
Then it's a matter of waiting for my specially adapted abs loom to come back to be fitted and my boa to sierra engine loom.
#195
Fart of the Purniture
I'm going to take some of the responsibility for that.
Although I did see you write somewhere, like you already knew, that you use the arms to suit the cross-member?
I used BOA arms, but used a BOA cross-member, but sure I have read that they will go on a standard one?
Any way, glad you got sorted in the end and things can move on.
#196
Sorry Wes.
I'm going to take some of the responsibility for that.
Although I did see you write somewhere, like you already knew, that you use the arms to suit the cross-member?
I used BOA arms, but used a BOA cross-member, but sure I have read that they will go on a standard one?
Any way, glad you got sorted in the end and things can move on.
I'm going to take some of the responsibility for that.
Although I did see you write somewhere, like you already knew, that you use the arms to suit the cross-member?
I used BOA arms, but used a BOA cross-member, but sure I have read that they will go on a standard one?
Any way, glad you got sorted in the end and things can move on.
#197
Fart of the Purniture
I'm afraid wiring an engine loom into an existing loom is not my area at all, I threw in the entire Granada loom to get it running and that was crazy enough - and I had major help with that LOL!, I started with a a completely bare Saff.
Good luck with it all.
Good luck with it all.
#198
I have an idea in my head if its right I hope it is I should be ok if not fuck knows lol.
The wires I think go into the car if I'm right I have to work out what wires are what on sierra loom going to original ecu then connect them to the same on the boa loom but theres a few i'm unsure of. I know I got to connect a wire or 2 to fuel pump, and to handbrake/brake pedal and wire to clocks for rev counter
The wires I think go into the car if I'm right I have to work out what wires are what on sierra loom going to original ecu then connect them to the same on the boa loom but theres a few i'm unsure of. I know I got to connect a wire or 2 to fuel pump, and to handbrake/brake pedal and wire to clocks for rev counter
#199
Fart of the Purniture
Found this on the FSOC
I don't know if it's gospel but seems legit
Hope it helps, get it cross referenced by someone else who has more of a clue
I don't know if it's gospel but seems legit
Originally Posted by Jeroen
If you got the three multiplugs behind the battery then it's easy; all you need is there
Ignition feed
Alternator light
Oil pressure light
Coolant temp gauge
Fuel pump relay coil +
Fuel pump relay coil -
VSS
Brakelight switch
Tacho
Ignition feed
Alternator light
Oil pressure light
Coolant temp gauge
Fuel pump relay coil +
Fuel pump relay coil -
VSS
Brakelight switch
Tacho
Hope it helps, get it cross referenced by someone else who has more of a clue
#200
ELASTIC BAND
that did apply to my loom and my random sketches i had, but when we was looking at Wes's he didnt have the 3 plugs, basically we think, an earlier loom, with viarious plugs, same cables but to several different plugs now