This is the end of one the fastest 1.6 CVH RS Turbos ever. A great deal of time and money went into making this car so all the parts are top quality and 90% of it was bought in 2004 or later. All parts were genuine Ford or better with no cheap pattern parts being used. Have a look at the restoration thread to see exactly what has gone into the car.

https://passionford.com/forum/restor...page-62-a.html


I have now broken the car. ALL parts are off and what is left is ready to be sold.




PLEASE NOTE - The shell is sold. I sold it complete. So no more emails and PM's about doors and sunroofs etc.

MUST ADD - I would prefer you to collect your parts, but I can ship out some stuff within reason at extra cost on top of prices below, unless otherwise stated. Payment through PayPal ONLY if you cover the fees, otherwise bank transfer, personal cheque or cash. Nothing is sold until I have had payment or deposit.

Email me at thetone69@ntlworld.com with the part in the subject for a much faster response than you will get from a PM. This helps me keep track as I have a lot of bits to handle.



PARTS LIST

Pictures and detailed explaination of parts below...

BITS I HAVE LEFT

Exhaust - £250
Grp A Monster K&N Air Filter & Trumpet - £50
FRST Coil Pack and bracket - £30
Starter motor - £30
Alternator and powder coated heat shield - £40
DEFI's;
Water Temp - £120
Oil Temp - £120
Boost - SOLD
Oil Pressure - SOLD
Fuel Pressure - SOLD
EGT - £160


SOLD STUFF

Engine (head and block with sump and pumps etc) - Prov SOLD
Inlet Manifold, Fuel Rail & TB with sensors - SOLD
Grey Injectors - SOLD
Aeromotive Fuel Reg - SOLD
Turbo and Exh Manifold - SOLD
Oil Cooler, mounts, lines and fittings - SOLD
Gearbox - Prov SOLD
B&M Shifter - SOLD
Clutch - SOLD
Modine Oil Cooler - SOLD
Vibra Technics gearbox mount - SOLD
Knock Link - SOLD
Header Tank - SOLD

Omex 710 ECU - SOLD
Wheels and tyres - SOLD
AP Brakes - SOLD
Turbo Technics ARB set up - SOLD
Copper Core Radiator and twin Spal HD fans - SOLD
GRS Intercooler - SOLD
Pro Alloy Turbo Cooler, brackets and hoses - SOLD

Flocked dashboard - SOLD
88 Spec Interior - SOLD


Control ECU mk2 - SOLD
Warning light - £20
STACK ST500SR speedo - SOLD
Knock Link - SOLD

A Piller Pod for 60mm gauge - SOLD
Genuine Weber 3 Bar MAP Sensor - SOLD
E1.6 RST number plate (only one in the country ) - SOLD

GT28RS TURBO






Genuine Garrett Turbo which have been built into a T3 flange with a V- Band quick release exhaust end. Having the T3 flange means it will bolt on to any T3 style manifold. This turbo cost me well over £1200 and has covered only 3000 miles. Selling with the exhaust manifold which has been ceramic coated and selling with the actuator.

£800




SAMCO BOOST HOSES



£50



MONGOOSE EXHAUST,








3 inch bore with a 4 inch rolled out tail pipe. In very good condition, comes with clamps, power flex mounts etc. Modified with a flexi joint and V band style downpipe. A V band to standard 4 bolt adapter can be bought from America if you need it for around £40.

£300

Obviously this was made to work with my GT28 turbo, if you want the turbo and the exhaust together we can work a deal out to make a really good "bolt on" package.



K&N GrpA Air filter with powder coated trumpet



£50



DEFI BF Gauges








These are the 1st generation BF gauges which are sort after and better looking than the ones Defi make now. They come with the gauge, wiring and sensor, no cups or feet. These can be bought for next to nothing through a Defi dealer should you require them.


Water Temp - £120
Oil Temp - £120
Boost - SOLD
Oil Pressure - SOLD
Fuel Pressure - SOLD
EGT - £160

Control ECU mk2 - SOLD
Warning light - £30



1600 CVH Engine












Engine spec is a low compression 1600 CVH with Farndon steel rods and Ross Racing pistions. No expense was spared and no corners have been cut in building this engine and has been bullet proof! Everything was bought new 11,000 miles ago, including new pumps, seals, bolts, sensors etc. Comes with the Cam sensor and mounting bracket which has never been used. The crank was sourced from a CVH that had done a mear 14,000 miles so it had as much original material on and needed minimal machining. The block was converted to EFi for me and had a fortune spent using all genuine Ford parts where ever possible, making it what it is today. The sump is genuine Ford and was bought new along with the rest of the parts. APT modified the sump with a baffle plate and a modified oil pick up. The engine always made good high oil pressure at around 2 bar @ idle at working temp. Which is bloody good for a CVH.

The head was a standard MFi which has been fully ported and polished with bigger top quality valves. The cam is a Newman cam which has done 3,000 miles, with solid lifters and double valve springs. Everything was speced and built by APT and it is equivilent specification to Christians old Top Speed engine. Obviously this engine is proven and no slug as I have done 161.2mph and kicked out 330bhp with it. This engine is capable of a lot more with the right bits. I am asking only £1200 for this engine and when you consider that it cost me more than that in machining alone then it is a bit of a bargain.

Everything you see in the photos on the trolley is what you get.

£1200 - prov SOLD



GEARBOX






The gearbox started life as a CTS Bernie stg2 box with a Quaife ATB diff. APT later fitted an oil drain bung into the casing. Then I had it stripped down a couple years ago and had the gears and shafts cryogenically frozen by one firm and then shot peened by another for maximum strength. Re-assembled and went into the car in September with NEW bearings and clutch fork and has done 500 testing miles.

£1200 - Prov SOLD




COPPER CORE Radiator and twin Spal HD Fans




This is original Ford end tanks welded on a high grade copper core. Copper is a far better material to use than alloy. Why do plumbers use expensive copper piping? I have done 2000 miles with the radiator and it is in great condition. One of the original brackets broke but was glued on using a high strength epoxy resin and hasn't broken off while the radiator has been in use. Will come with the top mounts than rest in the slam panel.

£150



E16 RST Number Plate




Currently on retention. Has to be the best number plate for a 1600 RS Turbo.

£800



Genuine Recaro/ Ford Foam Bolster




Brand New - £25 delivered



Rear Light Seal




Brand new - £12 delivered








Open to sensible offers on all parts. You never know what I'll let bits go for so MAKE AN OFFER - Thank you

 

i got all excited when you said it was coming back good luck selling the bits

 

Gearbox mate?

 

Gearbox is a CTS/APT/CTU combo. It came originally from CTS and I had the gears cryogenically frozen and shot peened, with a Quaife ATB diff, done 500 miles and went in the car in September. It's basically the same as the CTS stage 2+ gearbox but without the freezing.

I'm after £1200

 

Shell is sold!

 

how much for the brake set up with all pipe work to the front and rear calipers cheers

 

Glad shell sold and not scrapped.

 

Email sent

 

What exhaust is on it??

 

Sold! Sorry

 

A 3 inch bore mongoose with custome down pipe with v band fitting for the turbo

 

Sounds a great box but out of my price range im afraid, good luck with breaking it though matey

 

if you dont sell this in a week, i will most likely buy it, i been looking at a new one from CTS myself but this is the same thing, any ley way on the price ??? cheers

 

hey man,

could you put the full spec up, im always looking for parts, nothing in particular though

 

Tony have you still got the flocked bits??? shame to see this happening was one of my favourite rst's of all time!!!!!

 

how much for number plate

 

Mine is better than a CTS, you can have it in a couple of weeks and it's had an extra treatment and it's almost half the price lol.

There may be a bit of a give in the prices.

 

£1000, with no transfer fees

 

Thank you

Yeah still have the flocked bits except for the door handles - £300 for the lot

 

I just want the flocked sill covers, speaker pods and glovebox please m8 how much would you do them posted for? i did want the door handle's as well as i was going to have all of what i mentioned on your original breaking thread gutted you havent got them

 

I don't want to separate the glove box from the dashboard. Feel free to make an offer on the other bits.

 

kill for the flocked parts and the defis lol


shame to see it broken


good luck with the sale tony !!!

 

You don't have to kill for the parts, you can buy them lol

Thanks

 

How much for the rear smoked lights, posted ?

 

Sold with the shell

 

Price for wheels? Cheers.

Alex.

 

Can i see pics of the Turbo Technics Adjustable Anti- Roll Bar set up ?

Thanks

 

£750 ono

 

There are pics of it on the resto thread. I haven't got it off of the car yet but it still looks in great condition, just needs a clean up of course

 

when you said you sold the shell did the bumpers and mirrors go with it as im interested if so how much?

 

Shell was sold complete but I might have some mirrors in the loft. What you offering for me to go up and have look?

 

Haven't a clue what to offer for the flocked sill covers and speaker pods m8 give us a clue lol

 

Speaker pods are now sold. How about £50 delivered for the sill trims?

 

No thanks m8

 

No? What you mean no? That's not how you haggle lol

 

How much you want for the steering wheel pm me

 

lmao, well when you did the original breaking thread you were going to let me have the door pulls, speaker pods, sill covers for £50 and you were going to throw the speakers in too lol

 

It's sold

 

Really? That sounds awfully generous of me lol. Well I sold the speaker pods for £50 and I see you can get unflocked (is that even a word? Lol) sills for £20 I want to sell of course but don't want to give them away. If you still want them, make a counter offer. Let's dance lol

 

Do you still have the roll cage? How much you looking for mate?