Engine breaking, Head 138.95mm, Block, T34, BD10's etc etc
12-03-2008, 08:32 AM
#1
PassionFord Post Whore!!
Thread Starter
iTrader: (9)
Join Date: May 2003
Location: Essex/Middlesex
Posts: 7,836
Likes: 0
Received 0 Likes
on
0 Posts
Engine breaking, Head 138.95mm, Block, T34, BD10's etc etc
Ok I have just aquired a complete engine so I have the following for sale from my old engine;
Complete short engine done 80k 205 Block inc Crank pistons rods new oil pump 5k ago, new front covers /seals etc 5k ago. I am fairly sure this has never been apart before other than for a GRP A HG. The bores are standard size so I am guessing the crank etc are all standard size. Oil use was within book figures no leaks or anything £700
2wd Head 138.95mm (measured as shown so might be very slightly less once cleaned and checked?) one of the exhaust valves broke and the bit managed to go out the exhaust port otherwise its fine, I will supply new valve stem oil seals to fit so would just require an ex valve (prob best to change the guides etc as well). The chunk of valve has scored the exhaust port on the way out, however I wouldn't think this would be a problem and the seat may need a clean. The HG was mint when the head came off so it should just need a clean before refitting and have plenty of life left for future skims etc £500
2wd sump tapped for 1/8npt oil temp sender £50
Black powder coated inlet runners mildly polished as in top of this pic £30
Standard 2wd fuel rail PROVISIONALLY SOLD
T34 .48 polished housing 360 deg and cut back blades (So I was told) only ever run at 18psi never smoked, housing could do with a buff £350
Pair of BD 10's £120
Black powder coated cam pulleys as £30
2wd throttle body £40
ISCV £40
Chrome Rocker cover with breather take off £50
2wd Engine arms were chromed but flaking now £20
L8 ECU will have to check the baby board SOLD
2wd exhaust manifold PROVISIONALLY SOLD
2wd crank pulley PROVISIONALLY SOLD
2wd Turbo oil feed pipe £30
Chromed 2wd inlet with elbow £40
Chromed thermostat housing £20
Ford bottom rad pipe £20
2wd dizzy PROVISIONALLY SOLD
Very good condition (most would say mint) Front AND rear leather Recaros SOLD
Stage 3 chip for L8 Greens 803's I ran this with a T34 0.48 housing SOLD
More stuff to be added once I have taken it off the old engine
All the chrome stuff is flaking off and will need to be re done
Anything I do not have pictures for is NOT off the engine in the pics, I will get the rest of the pics tonight of the actual items.
I can get more/detailed pictures of anything so please ask
All prices exclude P&P
Complete short engine done 80k 205 Block inc Crank pistons rods new oil pump 5k ago, new front covers /seals etc 5k ago. I am fairly sure this has never been apart before other than for a GRP A HG. The bores are standard size so I am guessing the crank etc are all standard size. Oil use was within book figures no leaks or anything £700
2wd Head 138.95mm (measured as shown so might be very slightly less once cleaned and checked?) one of the exhaust valves broke and the bit managed to go out the exhaust port otherwise its fine, I will supply new valve stem oil seals to fit so would just require an ex valve (prob best to change the guides etc as well). The chunk of valve has scored the exhaust port on the way out, however I wouldn't think this would be a problem and the seat may need a clean. The HG was mint when the head came off so it should just need a clean before refitting and have plenty of life left for future skims etc £500
2wd sump tapped for 1/8npt oil temp sender £50
Black powder coated inlet runners mildly polished as in top of this pic £30
Standard 2wd fuel rail PROVISIONALLY SOLD
T34 .48 polished housing 360 deg and cut back blades (So I was told) only ever run at 18psi never smoked, housing could do with a buff £350
Pair of BD 10's £120
Black powder coated cam pulleys as £30
2wd throttle body £40
ISCV £40
Chrome Rocker cover with breather take off £50
2wd Engine arms were chromed but flaking now £20
L8 ECU will have to check the baby board SOLD
2wd exhaust manifold PROVISIONALLY SOLD
2wd crank pulley PROVISIONALLY SOLD
2wd Turbo oil feed pipe £30
Chromed 2wd inlet with elbow £40
Chromed thermostat housing £20
Ford bottom rad pipe £20
2wd dizzy PROVISIONALLY SOLD
Very good condition (most would say mint) Front AND rear leather Recaros SOLD
Stage 3 chip for L8 Greens 803's I ran this with a T34 0.48 housing SOLD
More stuff to be added once I have taken it off the old engine
All the chrome stuff is flaking off and will need to be re done
Anything I do not have pictures for is NOT off the engine in the pics, I will get the rest of the pics tonight of the actual items.
I can get more/detailed pictures of anything so please ask
All prices exclude P&P
Last edited by rsnissan; 26-03-2008 at 02:06 PM.
12-03-2008, 12:28 PM
#6
PassionFord Post Whore!!
Thread Starter
iTrader: (9)
Join Date: May 2003
Location: Essex/Middlesex
Posts: 7,836
Likes: 0
Received 0 Likes
on
0 Posts
yeah got a modine (needs a spruce up naturally), you can have it and take it off my tab for a loom 
I think I have replied to all the PM's so far
I think I have replied to all the PM's so far
Trending Topics
12-03-2008, 01:16 PM
#8
15K+ Super Poster!!
Join Date: May 2003
Location: Southampton
Posts: 18,589
Likes: 0
Received 0 Likes
on
0 Posts
cheers andy, yeah my one has a slight dent in one of the pipes so cant be arsed to risk putting it on.
hurry up and order a loom then and i'll knock £5 off your bill. lol
get that credit card out
hurry up and order a loom then and i'll knock £5 off your bill. lol
get that credit card out
12-03-2008, 05:11 PM
#11
PassionFord Post Whore!!
Thread Starter
iTrader: (9)
Join Date: May 2003
Location: Essex/Middlesex
Posts: 7,836
Likes: 0
Received 0 Likes
on
0 Posts
Front seats...............MINTOS I tell thee!
anyone thats seen them will tell you they are in excellent condition and they will also tell you I am 2 stone nothing and can barely touch the bolsters
so all in all the seats are in great condition
anyone thats seen them will tell you they are in excellent condition and they will also tell you I am 2 stone nothing and can barely touch the bolsters
so all in all the seats are in great condition
12-03-2008, 08:14 PM
#17
PassionFord Post Whore!!
Thread Starter
iTrader: (9)
Join Date: May 2003
Location: Essex/Middlesex
Posts: 7,836
Likes: 0
Received 0 Likes
on
0 Posts
LOL steve
you can run it on an L8 but it will need modding, with one of MSD chips I believe you can also run wasted spark and LC with the correct hardware/software
PewteRS
sorry the swirl pot is not for sale
PewteRS
sorry the swirl pot is not for sale
13-03-2008, 07:39 AM
#22
PassionFord Post Whore!!
Thread Starter
iTrader: (9)
Join Date: May 2003
Location: Essex/Middlesex
Posts: 7,836
Likes: 0
Received 0 Likes
on
0 Posts
Prob gonna chuck some buckets in there with harnesses and I have set of standard 3dr seats off Ryan to go in in the mean time
Id keep them but I have so much stuff that I just end up hoarding for the car its insane
Id keep them but I have so much stuff that I just end up hoarding for the car its insane
Last edited by rsnissan; 13-03-2008 at 07:40 AM.
16-03-2008, 11:41 PM
#28
PassionFord Post Whore!!
Thread Starter
iTrader: (9)
Join Date: May 2003
Location: Essex/Middlesex
Posts: 7,836
Likes: 0
Received 0 Likes
on
0 Posts
SillyFezzaMk1 what details are you after?
Tony sorry not selling the cam belt cover
simmosaph i'll split now uf you want the other
Tony sorry not selling the cam belt cover
simmosaph i'll split now uf you want the other
