PassionFord - Ford Focus, Escort & RS Forum Discussion
0 2019/03/19 14:34:25
0 2019/03/19 14:34:33
0 2019/03/19 14:34:43
0 2019/03/19 14:34:52
0 2019/03/19 16:32:01
0 2019/03/19 16:32:10
0 2019/03/19 16:32:19
Before we weld the panels in we blast on a few wet coats of production primer, it’s a Kent product, it’s extremely corrosive resistant
Before we weld the panels in we blast on a few wet coats of production primer, it’s a Kent product, it’s extremely corrosive resistant
0 2019/03/19 16:32:30
Leave a line for weld through
Leave a line for weld through
0 2019/03/19 16:32:42
0 2019/03/19 16:32:53
Blasted the inner sills with red lead also
Blasted the inner sills with red lead also
0 2019/03/19 16:33:03
0 2019/03/19 16:33:12
Sills on arches in drivers side ready to filler repair
Sills on arches in drivers side ready to filler repair
0 2019/03/19 16:33:21
I always keep a cover on even at this stage , it keeps the moisture in the air off the car
I always keep a cover on even at this stage , it keeps the moisture in the air off the car
0 2019/03/19 16:33:30
0 2019/03/19 16:49:09
0 2019/03/19 16:49:19
Turbo and manifold looked a bit the worse
Turbo and manifold looked a bit the worse
0 2019/03/19 17:05:40
Sent it to Mcm turbos
Sent it to Mcm turbos
0 2019/03/19 17:05:52
Got it back after a week looking like this
Got it back after a week looking like this
0 2019/03/19 17:06:03
0 2019/03/19 17:06:14
0 2019/03/19 17:06:23
Have got stuck in to the passenger side
Have got stuck in to the passenger side
0 2019/03/30 02:43:01
0 2019/03/30 02:43:11
Thanks sill after welds have been repaired in
Thanks sill after welds have been repaired in
0 2019/03/30 02:43:21
0 2019/03/30 02:43:30
0 2019/03/30 02:43:39
0 2019/03/30 02:43:48
0 2019/03/30 02:43:57
0 2019/03/30 02:44:06
Tried to keep the depth of filler to a minimum.
Tried to keep the depth of filler to a minimum.
0 2019/03/30 02:51:26
0 2019/03/30 02:53:47
0 2019/03/30 02:53:56
Right hand side all repaired in and etch primed , pretty happy with it . I’ll high build prime it on Friday night and see for certain, then I’ll block it all down p180 and p240 and it will be primed again when I’m priming the entire shell
Right hand side all repaired in and etch primed , pretty happy with it . I’ll high build prime it on Friday night and see for certain, then I’ll block it all down p180 and p240 and it will be primed again when I’m priming the entire shell
0 2019/04/04 02:25:03
Arch sits nice
Arch sits nice
0 2019/04/04 02:25:26
0 2019/04/04 02:25:40
All bagged up and I’m off home it’s almost 10 pm 😂 can’t leave it until I’m happy lol
All bagged up and I’m off home it’s almost 10 pm 😂 can’t leave it until I’m happy lol
0 2019/04/04 02:26:01
0 2019/04/04 02:26:16
They might be almost too glossy
They might be almost too glossy
0 2019/04/04 09:39:20
Took the lamps and wet sanded them p800 until all marks and wear was gone , then over again p1200 then a good rub grey scotchbrite, coat of clear plastic primer and a coat of lacquer, Opinions please.
Took the lamps and wet sanded them p800 until all marks and wear was gone , then over again p1200 then a good rub grey scotchbrite, coat of clear plastic primer and a coat of lacquer, Opinions please.
0 2019/04/04 09:39:48
Had a go at refurbing the old tail lights. They are a bit sorry looking and although I tried to find new ones I only managed to get stung with a pair of replica ones ,Lucas I believe they were ,
Had a go at refurbing the old tail lights. They are a bit sorry looking and although I tried to find new ones I only managed to get stung with a pair of replica ones ,Lucas I believe they were ,
0 2019/04/04 09:39:57