PassionFord - Ford Focus, Escort & RS Forum Discussion
Wilwood clutch master cylinder fitted
Wilwood clutch master cylinder fitted
0 2018/11/07 14:15:02
0 2018/11/07 14:15:01
0 2018/11/07 12:51:08
0 2018/11/07 12:50:56
0 2018/11/07 12:50:54
0 2018/10/17 13:57:34
My integra Dc5 shifter box & short shift has turned turned up, almost a perfect fit, just requires a little fettling, easy job for a change.
My integra Dc5 shifter box & short shift has turned turned up, almost a perfect fit, just requires a little fettling, easy job for a change.
0 2018/10/17 13:57:02
0 2018/10/05 13:32:04
0 2018/10/05 13:18:10
0 2018/10/05 13:16:01
0 2018/10/05 13:14:32
0 2018/10/05 13:09:45
0 2018/10/05 12:31:44
Made progress on the gear box mount which is now all done. Just need to give it a paint with zinc primer. Also mocked up the drivers mount..
Made progress on the gear box mount which is now all done. Just need to give it a paint with zinc primer. Also mocked up the drivers mount..
0 2018/09/27 10:32:24
0 2018/09/27 10:32:12
0 2018/09/27 10:32:05
0 2018/09/27 10:32:04
0 2018/09/27 10:31:33
0 2018/09/27 10:29:06
I went to a hillclimb yesterday, here in cornwall & got to view this... built by a cornish rally prep company. Complete subaru running gear/floorpan
I went to a hillclimb yesterday, here in cornwall & got to view this... built by a cornish rally prep company. Complete subaru running gear/floorpan
0 2018/09/16 10:48:51
0 2018/09/16 10:48:35
So this happened today. Such a good fit, there is alot of clearance which is always a good thing. I also decided to use the original Civic type r mounts & change at a later date. All in all a productive day!!!
So this happened today. Such a good fit, there is alot of clearance which is always a good thing. I also decided to use the original Civic type r mounts & change at a later date. All in all a productive day!!!
0 2018/09/14 09:59:35
0 2018/09/14 09:59:32
0 2018/09/14 09:59:18
0 2018/09/13 13:38:40
Ive made a basic frame with castor wheels.. also started to make an adjustable front gearbox mount using a jack..(May aswel use scrap parts) the driveshafts won't be a problem. I know of a motorsport company who makes shafts. I will have to cut both ends, make a sleeve & weld them, then the will be matched & made... im currently spending about an hour a day on it during lunch breaks at work so its not going to be a fast project..
Ive made a basic frame with castor wheels.. also started to make an adjustable front gearbox mount using a jack..(May aswel use scrap parts) the driveshafts won't be a problem. I know of a motorsport company who makes shafts. I will have to cut both ends, make a sleeve & weld them, then the will be matched & made... im currently spending about an hour a day on it during lunch breaks at work so its not going to be a fast project..
0 2018/09/11 10:35:59
0 2018/09/11 10:35:51
Today i got the wiring loom & auxiliaries removed, ready to fabricate a cradle for the engine/box to sit on. I plan on fitting castor wheels & adjustable brackets which enables me to level the engine with the correct 12° tilt which the K20 has from the factory.. makes life easier when it comes to the mounts ect...
Today i got the wiring loom & auxiliaries removed, ready to fabricate a cradle for the engine/box to sit on. I plan on fitting castor wheels & adjustable brackets which enables me to level the engine with the correct 12° tilt which the K20 has from the factory.. makes life easier when it comes to the mounts ect...
0 2018/09/10 11:12:42
0 2018/09/10 11:12:40
0 2018/09/09 12:17:04
0 2018/09/07 15:16:18
0 2018/09/07 15:16:09
0 2018/09/07 15:14:12
Pic for attention
Pic for attention
0 2018/08/15 14:27:51
0 2018/08/15 12:33:32
0 2018/08/15 12:32:58
Here's to the start of my orion project!
Here's to the start of my orion project!
0 2018/08/13 15:18:54