89' Magenta Saph cos. 64k with FSH. 360bhp. *SOLD*
Thread Starter
Has a large member
iTrader: (4)
Joined: Jun 2005
Posts: 4,186
Likes: 9
From: oxFORDshire
Well after 8 years of 80's and 90's fast ford loyalty ive decided its time to have a break. Still dont know if im doing the right thing but fancy something new in the garage. Please read advert fully, the engine needs attention.
The car is a 2wd Magenta red saph. 89' G reg.
64k from new with FSH
Original stamped up service book with ALL previous M.O.Ts
V5 present and HPI clear
MOT'd Till april 2012.
Car
17" rondells
RS500 splitter
4x4 bonnet
Mongoose exhaust with 4" outward rolled tip
Welded cosworth diff (bullet proof lol)
AP 6 Paddle clutch
4x4 cosworth rear calipers
Koni shocks and springs
Carbon mirrors
Carbon rear door triangles
Engine bay
Fully resprayed last year
T34.48 turbo
Grey injectors
SCS chip
Grp A filter
Roose RS500 hoses
Grp A coil & matt lewis loom
New dizzy and rotor arm
brand new HT leads
Bailey breather tank set up
Airtec RS500 cooler
New standard rad
Earls turbo oil pre filter
Sparco strut brace
Interior
Ravern leathers from factory
boost gauge
original mint ford rubber mats
uprated speakers
Rad fans are on a switch
Not so good points..
-The engine has seized and i assume will need a bottom end rebuild. I have no more patience or money to throw at old cars anymore so will be cutting my losses and passing a bargain onto someone else. I havnt stripped engine down so dont know extent of damage.
-Theres a rust spot on one of the rear arches, a tiny bit under the centre spoiler mount (hardly noticeable), and some stonechips on the front of car. paint is all original and still gleaming!
-The underside has never been welded and is very good. however the passenger front jacking point has dented in and will need the seam welding a few inches where its split.
Price is £3995. no offers.
Pm me or ring me on 07769 329 392.











The car is a 2wd Magenta red saph. 89' G reg.
64k from new with FSH
Original stamped up service book with ALL previous M.O.Ts
V5 present and HPI clear
MOT'd Till april 2012.
Car
17" rondells
RS500 splitter
4x4 bonnet
Mongoose exhaust with 4" outward rolled tip
Welded cosworth diff (bullet proof lol)
AP 6 Paddle clutch
4x4 cosworth rear calipers
Koni shocks and springs
Carbon mirrors
Carbon rear door triangles
Engine bay
Fully resprayed last year
T34.48 turbo
Grey injectors
SCS chip
Grp A filter
Roose RS500 hoses
Grp A coil & matt lewis loom
New dizzy and rotor arm
brand new HT leads
Bailey breather tank set up
Airtec RS500 cooler
New standard rad
Earls turbo oil pre filter
Sparco strut brace
Interior
Ravern leathers from factory
boost gauge
original mint ford rubber mats
uprated speakers
Rad fans are on a switch
Not so good points..
-The engine has seized and i assume will need a bottom end rebuild. I have no more patience or money to throw at old cars anymore so will be cutting my losses and passing a bargain onto someone else. I havnt stripped engine down so dont know extent of damage.
-Theres a rust spot on one of the rear arches, a tiny bit under the centre spoiler mount (hardly noticeable), and some stonechips on the front of car. paint is all original and still gleaming!
-The underside has never been welded and is very good. however the passenger front jacking point has dented in and will need the seam welding a few inches where its split.
Price is £3995. no offers.
Pm me or ring me on 07769 329 392.











Last edited by ram; Aug 22, 2011 at 07:40 PM.
Trending Topics
Thread Starter
Has a large member
iTrader: (4)
Joined: Jun 2005
Posts: 4,186
Likes: 9
From: oxFORDshire
Thanks for the comments guys. Hopefully will be a quick sale as i dont have the time to break it but know i would get more money that way. would prob end up rebuilding it!
Mo - I've just had enough mate. Hardly used it this year, spent £1000's on bits, and now it wants engine work lol. Im selling my M3 too and going evo 8, although im already on the lookout for an escos shell for a longterm ford project
Mo - I've just had enough mate. Hardly used it this year, spent £1000's on bits, and now it wants engine work lol. Im selling my M3 too and going evo 8, although im already on the lookout for an escos shell for a longterm ford project
Thread Starter
Has a large member
iTrader: (4)
Joined: Jun 2005
Posts: 4,186
Likes: 9
From: oxFORDshire
Are there any cossie parts you dont have rich! dont tempt me lol.
M3 will be up for 11k mate. Getting it serviced, mot'd and detailed this month then it will be up for sale. you still thinking bout one?
M3 will be up for 11k mate. Getting it serviced, mot'd and detailed this month then it will be up for sale. you still thinking bout one?
aka Turbosailorboy
iTrader: (5)
Joined: Apr 2005
Posts: 6,527
Likes: 21
From: Under the water.... .......in a nuclear submarine
I can't help myself

its a 200 block'd standard engine built by SCS about 7k ago. Came out of Ryan's(loom monkey) 3 door. Perfect for yours
I wish i had bought one now instead of the Escos project

Jacko996's shell would be a good buy for you later in the year

its a 200 block'd standard engine built by SCS about 7k ago. Came out of Ryan's(loom monkey) 3 door. Perfect for yours

Jacko996's shell would be a good buy for you later in the year
Thread Starter
Has a large member
iTrader: (4)
Joined: Jun 2005
Posts: 4,186
Likes: 9
From: oxFORDshire
Ha well i'll leave it for the next owner to sort the engine out! sounds a good one for them though. would you split it as the head on mines ok.
Ive seen jacko's car in his sig but dont know much about it. shell seems exactly what im after though as i want to build a rwd escos track car
Ive seen jacko's car in his sig but dont know much about it. shell seems exactly what im after though as i want to build a rwd escos track car
Thanks for the comments guys. Hopefully will be a quick sale as i dont have the time to break it but know i would get more money that way. would prob end up rebuilding it!
Mo - I've just had enough mate. Hardly used it this year, spent £1000's on bits, and now it wants engine work lol. Im selling my M3 too and going evo 8, although im already on the lookout for an escos shell for a longterm ford project
Mo - I've just had enough mate. Hardly used it this year, spent £1000's on bits, and now it wants engine work lol. Im selling my M3 too and going evo 8, although im already on the lookout for an escos shell for a longterm ford project

just buy the escy..sack the evo
Know This Car Personally, Did A Lot Of Miles In It Myself When My Mate Owned It. Genuine, Honest, Clean, Straight Saff. Wish I Had The Money, Loved Driving This Car, Drives VERY Well.
GLWTS Ram
GLWTS Ram
I've found that life I needed.. It's HERE!!
iTrader: (3)
Joined: Jul 2007
Posts: 1,231
Likes: 6
From: Peterborough
[QUOTE=Richie.;5587418]I can't help myself

its a 200 block'd standard engine built by SCS about 7k ago. Came out of Ryan's(loom monkey) 3 door. Perfect for yours
How much for the engine??

its a 200 block'd standard engine built by SCS about 7k ago. Came out of Ryan's(loom monkey) 3 door. Perfect for yours
How much for the engine??
Thread Starter
Has a large member
iTrader: (4)
Joined: Jun 2005
Posts: 4,186
Likes: 9
From: oxFORDshire
Gary - Time to move on! I fancy a long term escos track car project next.
and an evo for the road.
Paul - Yes mate im working on a 'build 1 of 1 ram raider special edition' plaque for the centre console
Rab - cheers mate, wondering if ive underpriced it! someone coming to view early this week so hopefully it will go as my urge to rebuild and keep it is getting stronger everyday!
Paul - Yes mate im working on a 'build 1 of 1 ram raider special edition' plaque for the centre console

Rab - cheers mate, wondering if ive underpriced it! someone coming to view early this week so hopefully it will go as my urge to rebuild and keep it is getting stronger everyday!
Gary - Time to move on! I fancy a long term escos track car project next.
and an evo for the road.
Paul - Yes mate im working on a 'build 1 of 1 ram raider special edition' plaque for the centre console
Rab - cheers mate, wondering if ive underpriced it! someone coming to view early this week so hopefully it will go as my urge to rebuild and keep it is getting stronger everyday!
Paul - Yes mate im working on a 'build 1 of 1 ram raider special edition' plaque for the centre console

Rab - cheers mate, wondering if ive underpriced it! someone coming to view early this week so hopefully it will go as my urge to rebuild and keep it is getting stronger everyday!
Good luck with the sale!
Thread Starter
Has a large member
iTrader: (4)
Joined: Jun 2005
Posts: 4,186
Likes: 9
From: oxFORDshire
Sold to DanielBetty to first person to come and view it.
Rab - maybe it was abit too cheap but i wanted a quick sale as i was on the verge of keeping it, which i didnt want to do! Still looked great as it left on the back of the flat bed
It's getting the SCS rebuild treatment so look forward to seeing it live on
Rab - maybe it was abit too cheap but i wanted a quick sale as i was on the verge of keeping it, which i didnt want to do! Still looked great as it left on the back of the flat bed

It's getting the SCS rebuild treatment so look forward to seeing it live on
Thread
Thread Starter
Forum
Replies
Last Post



Ram you nutter!!

