141 bhp fiesta zetec s (PERFORMANCE FORD FEATURED MAY 2010!!!!!)

[hatton89]

Hello guys and girls .im new to the site so i thought i would start a project, the spec is:- Engine:- 1.6 16 valve shawspeed tuned engine SS4 high lift cams ARP heavy duty big end bolts 1.7 puma inlet manifold MSD super chip mapped to SS4 spec with the rev limiter mapped off Omex rev limiter set at 7800rpm Omex launch control set at 4000rpm Magneco HT leads Pipercross panel filter 4-2-1 milltek sport evo manifold Milltek decat pipe Custom cat back system with duel exit oval tail pipes Custom cold air feed to air box Full blue samco hoses Engine dress up jenvey DTH 42mm bodies(soon to be fitted) Transmition:- Helix organic clutch Helix pressure plate ShawSpeed lightened and balanced flywheel Interior:- Stripped and painted rear Show cage Cobra monaco pro bucket seats Cobra sub frames 3 point cobra harnesses Chrome rear strut brace Nu-suede door cards Nu-suede A pillars Nu-suede boot cover Nu-suede glove box Nu-suede vent surrounds Nu-suede fuse box cover Nu suede air bag cover with omex 600 mounted in it Blue dial and dash conversion Ford racing puma steering wheel Puma gear knob painted blue numbers Omex launch control mounted on dash 6x9 speakers mounted in rear quater panels on custom frames Alcantra gear and handbrake gaitors Custom floor mats Fluffy hand cuffs Exterior:- Custom mk5 bonnet with mk4 rs turbo bonnet vents sprayed gloss black Roof and roof rails sprayed gloss black Gloss black spoiler Front grill surround sprayed gloss black Gloss black door handles Gloss black mirrors Gloss black front and rear bumper strips Gloss black lower grill and bumper lip Side strips removed Smoked ultra front lights Freestyle grill Black fog lights Smoked side repeaters MHW rear lights(defiltered) Ford logo mud flaps Smoked wind deflectors Smooth boot handle Debadged boot lid Private number plates Bonnet raisers Suspension:- AP sport coilover kit lowered approx 60mm OMP lower strut brace e-tec front upper strut brace 57mm chrome rear strut brace Vibr technics gear box mount Brakes:- Mondeo mk2 2.5 v6 280mm callipers 280mm discs green stuff pads dot 4 fluid Wheels and tyres:- Genuine escort cosworth alloys (summer wheels) Toyo t1r's stretched 195/45/16 Standard zetec s alloys sprayed gloss black with st 170 center caps(winter wheels) 195/50/15 michelin exalto pz2's

If you were logged in, you wouldn't be seeing this ad! Register your free account today, or log in if you already have an account.

[Ginge]

Originally Posted by hatton89

Hello guys and girls .im new to the site so i thought i would start a project,the spec is:-

Engine:-

1.6 16 valve shawspeed tuned engine, SS4 high lift,cams ARP heavy duty big end bolts 1.7 puma inlet manifold MSD super chip mapped to SS4 spec with the rev limiter mapped off. Omex rev limiter set at 7800rpm, Omex launch control set at 4000rpm.

Magneco HT leads,Pipercross panel filter,4-2-1 milltek sport evo manifold,Milltek decat pipe and Custom cat back system with duel exit oval tail pipes. Custom cold air feed to air box,Full blue samco hoses.

Interior:-

Stripped and painted rear,Show cage Cobra monaco pro bucket seats,Cobra sub frames3 point cobra harnesses.
Chrome rear strut brace, Nu-suede door cards, Nu-suede A pillars,Nu-suede boot cover.

Blue dial and dash conversion, Ford racing puma steering wheel,Puma gear knob painted blue numbers. Flocked dash parts,Omex launch control mounted on dash.

6x9 speakers mounted in rear quater panels on custom frames,Alcantra gear and handbrake gaitors,Custom floor mats and Fluffy hand cuffs

Exterior:-

Custom mk5 bonnet with mk4 rs turbo bonnet vents sprayed gloss black,Roof and roof rails sprayed gloss black,Gloss black spoile,rFront grill surround sprayed gloss black.
Gloss black door handles Gloss black mirrors Gloss black front and rear bumper strips,Gloss black lower grill and bumper lip.

Side strips removed,Smoked ultra front lights,Freestyle grill,Black fog lights,Smoked side repeaters,MHW rear lights(defiltered)Ford logo mud flaps.
Smoked wind deflectors,Smooth boot handle,Debadged boot lid,Private number plates,Bonnet raisers.

Suspension:-

AP sport coilover kit lowered approx 60mmOMP lower strut bracee-tec front upper strut brace57mm chrome rear strut brace

Brakes:-

Mondeo mk2 2.5 v6 280mm callipers,280mm discsgreen stuff pads,dot 4 fluid

Wheels and tyres:-

Genuine escort cosworth alloys (summer wheels)Toyo t1r's stretched 195/45/16

Standard zetec s alloys sprayed gloss black with st 170 center caps(winter wheels)195/50/15 michelin exalto pz2's

I kind of altered it for you so it is easier for reading.

It is no doubt completely grammatically incorrect but meh i couldnt care it was just a nightmare to read.

We need some pics of this car as well, project sounds great

Ginge

[hatton89]

thanks alot i did set it out all nice but it automatically edited itself

and i cannot add photos?? i have used photobucket to

[hatton89]

here are a few pictures of how it stands today... i bought the car from bog standard and have had alot of work done by myself and others

[hatton89]

just been looking at this on ebay thinking on getting this sometime next year after i get my throttle bodies

[andy130]

looks good mate, love ZS

[hatton89]

Originally Posted by andy130

looks good mate, love ZS

thanks mate

[DarrinDD]

Welcome, and finally sorted your issue with the site lol.

Looking good as always mate!

[escort van s.n]

nice car mate, the wheels andblack bonnet really set it off, top work!

[hatton89]

Originally Posted by escort van s.n

nice car mate, the wheels andblack bonnet really set it off, top work!

thank you

[hatton89]

Originally Posted by DarrinDD

Welcome, and finally sorted your issue with the site lol.

Looking good as always mate!

thanks dude :P

[Fiesta_ie]

realy nice car it's real carbon hood?
any pics of the engine?

[DarrinDD]

Its not carbon, just painted black!

[hatton89]

Originally Posted by DarrinDD

Its not carbon, just painted black!

along with rs turbo vents

[hatton89]

only one i got



a set of jenvey 45mm trumpets ready to be attached to a set of jenvey dth throttle bodies next year

[hatton89]

as im going to be fitting throttle bodies in the new year i got in contact with jon at shawspeed last night and ordered a few things....

• throttle position sensor
• air temperature sensor
• coolant temperature sensor
• upgraded fuel pressure regulator
• injector blanks

as im in no rush and funds dont allow im collecting part slowly every month

next will be the actual jenvey dth bodies and omex 600

[pjdj1989]

Sounds good hatton..! Boddies are getting close now..

Its phil_j from zsoc btw..

[hatton89]

Originally Posted by pjdj1989

Sounds good hatton..! Boddies are getting close now..

Its phil_j from zsoc btw..

yo whats happening fella!

tell me about it mate its getting to the point i cannot sleep because im thinking about them haha!! you going to fitp?

thats my dead line for them

[pjdj1989]

Yeah, think all us NW lot are gonna try and get down this year and represent our end!

I cant wait to be able to get cams, let alone boddies.. Imagine the drive home!

[hatton89]

Originally Posted by pjdj1989

Yeah, think all us NW lot are gonna try and get down this year and represent our end!

I cant wait to be able to get cams, let alone boddies.. Imagine the drive home!

the drive home after cams was wicked enough!!!

my mate has a 170bhp civic and we came off the round about and he was on the inside lane i was coming round him till i hit the 6700rpm limiter
got my new chip now and i think its reving to 7100rpm still not peak power but i dont want to raise it anymore incase im doing something wrong!

i will wait till track and road set it up correct at 7800rpm :P

[JackCornick]

Mate nice! I remember you from ZSOC, but I left there over a year ago. You've been busy. It looks good, impressive spec aswell

[pjdj1989]

Lol, at least it'll get sorted! I think I'd go TnR after hearing peoples experiances of them..

[hatton89]

Originally Posted by JackCornick

Mate nice! I remember you from ZSOC, but I left there over a year ago. You've been busy. It looks good, impressive spec aswell

thanks alot fella

changed alot since a year ago :P

its an ongoing project i love it

[hatton89]

Originally Posted by pjdj1989

Lol, at least it'll get sorted! I think I'd go TnR after hearing peoples experiances of them..

yea they seem the dogs!

my problem is i want the most powerful ss4 tuned zetec haha

[boris]

Hi there, nice fiesta you've got there! Just wondering, did the brakes fit straight on or do you have to drill out the calliper mounts? cheers

[hatton89]

Originally Posted by boris

Hi there, nice fiesta you've got there! Just wondering, did the brakes fit straight on or do you have to drill out the calliper mounts? cheers

hello

thanks fella

you need to drill the hub holes out with a 12mm bit!
then fit 3mm spacers behind the discs so the disc clears the abs rings.

you can also fit a 300mm kit but the calipers and carriers need to be shaved to clear 15" zetec s wheels

[hatton89]

decided to order more little things today! im addicted to oredring parts for the car lol

i ordered....(all from shawspeed) top service!

Omex programming kit

Connectors for management loom

3 metres fuel pipe c/w 6 off clips

Vacuum pipe adaptor

[Twins]

Love the look of the car

[hatton89]

Originally Posted by Twins

Love the look of the car

thank you mate

[Dan track ka]

Proper sweet matey. One of my fav fiesta's built.

You got the styling spot on.

[hatton89]

Originally Posted by Dan track ka

Proper sweet matey. One of my fav fiesta's built.

You got the styling spot on.

thanks alot mate

[hatton89]

i have been thinking over the last few days on another one of a kind mod,finally found the item i wanted so waiting for that to arrive then im going to take it from there,should be a nice touch once done, im not reveling what just yet as im unsure on what will happen if i can pull it off and what it would look like

[hatton89]

decided to scrap my mod!got a few issues with spluttering today!!

the car is realy hesitating and popig a spitting flames like mad haha!

i pushed the ht leads on and every thing seems to be fine,so tomorrow im going to take plugs out and have a look see whats up

[hatton89]

all seems fine now with the car

been and ordered some more goodies again from shawspeed :P

i also found out the other day that i need a new gear box mount as its almost touching the lower strut brace

so a VT shall be on order soon as i get payed

[Brian]

Very nice


Brian

[hatton89]

Originally Posted by Brian

Very nice


Brian

thanks brian

[hatton89]

went up the garage yesterday and stripped the old engine mount off(major ball ache)

and its fubar

so another one is on order and will be here in a few days,

also found out where to top my gear box oil as im losing a small amount every so often so im happy with that

now the car is off the road some bufty action can go on :P

[hatton89]

just been up the garage in the freezing cold

topped up my gear box oil and had a check around the car, what i did notice was alot of water around the spark plugs! i think its coming from the bonnet vents so dried it all up and sprayed it all with WD40, so going to see how it goes.

while im bored in the house i started to polish up my ITB trumpets ready looking alot better already pics to follow

[cossiejsy]

very nice motor mate

[hatton89]

Originally Posted by cossiejsy

very nice motor mate

thanks you fella its getting there